Scoobster
15-07-2012, 03:36 PM
Hong Nor Ultra LX2 marketed as the Ultimate RTR, I bought this from Modelsport about 4 weeks ago along with a few extras for it
Great spec RTR buggy including
Hong Nor HNT-3 2.4G steer wheel radio
All new cab forward pre-printed body
Force .25 Force nitro engine
High flow air filter for maximum engine protection
145cc fuel tank with integrated holding clips and splash guard
3 shoe competition clutch
CNC machined steel clutch bell
Front universal joint drive shafts
4mm aluminium shock towers F/R
16mm Big-Bore oil filled aluminium shocks
Front and Rear chassis braces
Hard coated aluminium chassis
Front and Rear sway bar
Complete set of rubber sealed ball bearings
Hi-down force wing
Its still not fully ran in and is still running very rich, it comes with a set of Fastrax 1/8th Cut Slick On-Road Tyres On Y-Spoke Wheels that are stored on a 1/8 Ansmann Racing Aluminium Wheel Holder which I was using to run the car in on a local car park. The RX is powered by a Core RC 1600mAH NiMh 6v RX Hump Pack. I have also fitted an upgraded metal gear Power HD HD9001MG with 9.8kg/cm Torque and speed of 0.14s/60 at 6V
As you can see from the underside it hasn’t had much use but I did have a little roll over at my local park which scratched the top of the cooling fins on the motor but I have touched these in so can’t really see them now.
In total I think its all cost me around £280 so looking for £200 for it all
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01197.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01198.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01199.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01200.jpg
Great spec RTR buggy including
Hong Nor HNT-3 2.4G steer wheel radio
All new cab forward pre-printed body
Force .25 Force nitro engine
High flow air filter for maximum engine protection
145cc fuel tank with integrated holding clips and splash guard
3 shoe competition clutch
CNC machined steel clutch bell
Front universal joint drive shafts
4mm aluminium shock towers F/R
16mm Big-Bore oil filled aluminium shocks
Front and Rear chassis braces
Hard coated aluminium chassis
Front and Rear sway bar
Complete set of rubber sealed ball bearings
Hi-down force wing
Its still not fully ran in and is still running very rich, it comes with a set of Fastrax 1/8th Cut Slick On-Road Tyres On Y-Spoke Wheels that are stored on a 1/8 Ansmann Racing Aluminium Wheel Holder which I was using to run the car in on a local car park. The RX is powered by a Core RC 1600mAH NiMh 6v RX Hump Pack. I have also fitted an upgraded metal gear Power HD HD9001MG with 9.8kg/cm Torque and speed of 0.14s/60 at 6V
As you can see from the underside it hasn’t had much use but I did have a little roll over at my local park which scratched the top of the cooling fins on the motor but I have touched these in so can’t really see them now.
In total I think its all cost me around £280 so looking for £200 for it all
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01197.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01198.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01199.jpg
http://i85.photobucket.com/albums/k65/scoobster_28/DSC01200.jpg