Chris Green
28-09-2008, 10:20 PM
Hello all,
I have an FTX Blaze ST For sale.
The car has a heavily modified and lightened chassis, set-up to run lipo's. With all electrics installed, I had this down to 707g, which makes it one of the lightest Blaze ST's around.
The following hop-ups are included;
Ball Diffs front and rear, cost £30
Alluminium Driveshafts front and rear, cost £28
Duratrax Alloy Pro Shock absorbers, cost £30
Anti-roll bars front and rear, with 3 roll bars for the front, and 2 for the rear.
PhatBodies Dudu bodyshell, and PhatBodies lexan wing.
I will also include a set of Gecko foams.
Please note, the electrics are not included.
I am after £115. Just in time for the Micro Nationals.
http://img.photobucket.com/albums/v630/chrisgreen82/CopyofSNV32326.jpg
http://img.photobucket.com/albums/v630/chrisgreen82/CopyofSNV32330.jpg
I also have the following spares available separately;
Brand new set of Gecko foams, a pair 37 shore's, and a pair of 40 shore's. both pairs are trued down to 58mm approx. The 40 shores have been narrowed by a couple of mm. This is a common setup for blazes and ST's. £9.
Front Lower ST Wishbones - £3.
Front Upper ST Wishbones - £3.
Rear Lower ST Wishbones - £3.
Rear upper tielinks ST - £3.
2 x Tornado 1000mah 25C Lipo packs. have been used at 4 meetings. very good condition, fitted with deans connectors. £8 per pack.
ST Springs - Blue - Pair - £3. 2 pairs available
ST Springs - Green - Pair - £3. 2 Pairs available
ST Springs - Yellow - Pair £2. a few coils cut off these. 2 pairs available.
Blaze Atomic Ball Diff rebuild kit - £2. including plates, main balls, and thrust-race balls.
Kit ST Shocks, Plastic ones - £10 for 4. no springs.
Anderson Pro Blaze motor - 32,000 rpm, used for 2 meetings. £7.
Anderson Pro Blaze motor - 32,000 rpm, used for 2 meetings. mounting screws slightly stripped, but it it possible to use associated screws to mount this instead. - £5.
Anderson kit motor - £4.
All prices are excluding delivery.
Thank you,
Chris.
I have an FTX Blaze ST For sale.
The car has a heavily modified and lightened chassis, set-up to run lipo's. With all electrics installed, I had this down to 707g, which makes it one of the lightest Blaze ST's around.
The following hop-ups are included;
Ball Diffs front and rear, cost £30
Alluminium Driveshafts front and rear, cost £28
Duratrax Alloy Pro Shock absorbers, cost £30
Anti-roll bars front and rear, with 3 roll bars for the front, and 2 for the rear.
PhatBodies Dudu bodyshell, and PhatBodies lexan wing.
I will also include a set of Gecko foams.
Please note, the electrics are not included.
I am after £115. Just in time for the Micro Nationals.
http://img.photobucket.com/albums/v630/chrisgreen82/CopyofSNV32326.jpg
http://img.photobucket.com/albums/v630/chrisgreen82/CopyofSNV32330.jpg
I also have the following spares available separately;
Brand new set of Gecko foams, a pair 37 shore's, and a pair of 40 shore's. both pairs are trued down to 58mm approx. The 40 shores have been narrowed by a couple of mm. This is a common setup for blazes and ST's. £9.
Front Lower ST Wishbones - £3.
Front Upper ST Wishbones - £3.
Rear Lower ST Wishbones - £3.
Rear upper tielinks ST - £3.
2 x Tornado 1000mah 25C Lipo packs. have been used at 4 meetings. very good condition, fitted with deans connectors. £8 per pack.
ST Springs - Blue - Pair - £3. 2 pairs available
ST Springs - Green - Pair - £3. 2 Pairs available
ST Springs - Yellow - Pair £2. a few coils cut off these. 2 pairs available.
Blaze Atomic Ball Diff rebuild kit - £2. including plates, main balls, and thrust-race balls.
Kit ST Shocks, Plastic ones - £10 for 4. no springs.
Anderson Pro Blaze motor - 32,000 rpm, used for 2 meetings. £7.
Anderson Pro Blaze motor - 32,000 rpm, used for 2 meetings. mounting screws slightly stripped, but it it possible to use associated screws to mount this instead. - £5.
Anderson kit motor - £4.
All prices are excluding delivery.
Thank you,
Chris.