Discharging problems on a Pro Trak

[markc]

Hi,

Ive recently bought a second hand Pro Trak, but whenever I try to discharge any of my cells it gets about 10 seconds into the discharge then comes up with a 'Check External Fuse' fault and terminates the discharging.

I've checked the fuses on the sides of the charger and they look ok.

Anybody have any ideas what this might be?

Cheers

Mark

[Rick]

There is a fuse inside the casing, cannot remember exactly where. I had this a lot, also had to send it back once for the discharge fets to be replaced. I ended up selling mine due to this.

Have you checked out the protrak site, or do a search on racechat as that is where I got the info to fix mine.

[Chequered Flag Racing]

I've checked the fuses on the sides of the charger and they look ok.



have you put a dvm across them to make sure?

does it stop altogether or does the discharge display keep counting?

if it's still counting time, mah's etc the discharge fets will more then likely be dead and need replacing

You could also try removing the ROM on the circuit board and refitting it. It's the large one to the left of the keypad and is easily removed. Note the direction it's fitted before removal. Should be a small half moon in the edge that points to the heat sink. After replacement you will need to recalibrate the unit.

calibration info page 10 & 11 (http://www.pro-trak.pwp.blueyonder.co.uk/contents.htm)
starts from were it says Resetting calibration after memory cleared.
You'll need to do static, charge & discharge calibrtaion.

HTH

[markc]

Thanks for the reply! I've just had the case apart but can't seem to see another fuse in there.

Yeah I've checked the Pro-Trak site but there was no info on there, I've emailed Phil at Pro-Track but had no reply so far. I'll have a look on RCrace chat and see if I can find any info on there.

Cheers

Mark

[markc]

Ive checked the fuse with a meter and it is ok.

It just terminates the discharge altogether & goes back to the main menu.

I'll give it a go with removing the ROM and see if that makes any difference.

Thanks for your help!

Mark

[Chequered Flag Racing]

I've emailed Phil at Pro-Trak but had no reply so far.



His email used to mine in the junk folder :woot: and he kept missing them

try his phone #'s on the site

[Rick]

I think the fuse is under the circuit board, I would try to find this before removing the ROM. it took me a while to find it, but trust me there is one in there and it does have this effect if blown.

http://www.rcracechat.com/vb/showthread.php?t=25920&highlight=protrak

This thread explains where the fuse is

[markc]

try his phone #'s on the site

Tried giving him a ring but there's no answer on the landline and his mobiles off, which I could understand for this time of night.

I'll try again tomorrow if I dont get sorted.

Cheers!

Mark

[markc]

I think the fuse is under the circuit board, I would try to find this before removing the ROM. it took me a while to find it, but trust me there is one in there and it does have this effect if blown.

http://www.rcracechat.com/vb/showthread.php?t=25920&highlight=protrak

This thread explains where the fuse is

Ok, thanks mate! I'll have a look at that thread and see if I can find the fuse.

Thanks again!

Mark

[markc]

I think the fuse is under the circuit board, I would try to find this before removing the ROM. it took me a while to find it, but trust me there is one in there and it does have this effect if blown.

http://www.rcracechat.com/vb/showthread.php?t=25920&highlight=protrak

This thread explains where the fuse is

I cant find the fuse, even reading the thread I still cant see it!...I must be going blind! :(

[Sean L]

Tried giving him a ring but there's no answer on the landline and his mobiles off, which I could understand for this time of night.

I'll try again tomorrow if I dont get sorted.

Cheers!

Mark


Hi mark,

i've also been tryin to get in touch with phil, for weeks now, both phone numbers always with the same response as u got :confused:. also no replies to e-mail. if u manage to get in touch with phil could u give me a shout.

Cheers

Sean.

[Rick]

I cant find the fuse, even reading the thread I still cant see it!...I must be going blind! :(


Sorry mate cant help as its 12 months since I got rid of mine, I remember changing it but cannot remember where it was.

As I said it just failed too often on discharge, someone told me that the older ones (20 amp discharge) cannot cope with the new high capacity cells, although if you know what you are doing you can upgrade it by fitting more or bigger fets, but its beyond me.

Good luck in getting it sorted

[markc]

Sorry mate cant help as its 12 months since I got rid of mine, I remember changing it but cannot remember where it was.

As I said it just failed too often on discharge, someone told me that the older ones (20 amp discharge) cannot cope with the new high capacity cells, although if you know what you are doing you can upgrade it by fitting more or bigger fets, but its beyond me.

Good luck in getting it sorted

Thanks alot for your help anyway mate! I've managed to get in touch with Phil and he says it needs to go back to him, he thinks the discharge is goosed! :( Thanks again though!!!!

Hi mark,

i've also been tryin to get in touch with phil, for weeks now, both phone numbers always with the same response as u got :confused:. also no replies to e-mail. if u manage to get in touch with phil could u give me a shout.

Cheers

Sean.

Hi Sean,

Managed to get in touch with him today via the email address on his wewbsite, and to ring him via landline.

Mark