ProCat MMS layshaft spur gear

[Northy]

I know this is a long shot but does anyone have any of these spur gears that fit on an ProCat MMS layshaft?

http://i20.photobucket.com/albums/b213/Northynorthy/Spurgear.jpg

I'm in a desparate need of some smaller than 92 teeth. :(

Cheers,

G

[Medders]

Yes. But I still have ambitions to rebuild my Procat so I'll check what I have and see what I can spare. What size do you want ideally?

Do you have any spare rear suspension, rear suspenion brackets, bodyshells and a rear wheel ? (thats what i'm missing :D )

[Northy]

You could well be my hero!

What sizes were available less than 92 tooth? Schumacher list 89 and 86, but these are aftermarket. An 86 would probably get me closer to the ideal ratio.

I have the suspension parts that you need I think, what parts are you after exactly?

Sorry to be a bit pushy, but when could you look? I could do with getting this sorted to race on Saturday night.

Cheers,

G

[DCM]

G, you could try www.rwracing.co.uk, he makes all sorts of things.

[Medders]

You could well be my hero!

What sizes were available less than 92 tooth? Schumacher list 89 and 86, but these are aftermarket. An 86 would probably get me closer to the ideal ratio.

I have the suspension parts that you need I think, what parts are you after exactly?

Sorry to be a bit pushy, but when could you look? I could do with getting this sorted to race on Saturday night.

Cheers,

G

I've had an initial look and most of what I have are way bigger than 100. My car currently has a 120 fitted to it although I'm not even sure its the same fitting (I modified so much on it I can't remember what was what :D ) The only one I have smaller that will defo fit appears way too stripped to be useful. I have one more small box of stuff to look through but i dont hold out much hope i'm afraid. Sorry mate.

See below pic of the rear end of my procat, its pretty obvious what is missing, along with the body shell :D . The front end etc is totally complete.

These truly were great cars at the time :cool:

http://i10.photobucket.com/albums/a148/totalrubbish/procatrear.jpg (http://i10.photobucket.com/albums/a148/totalrubbish/procatrear.jpg)

[Northy]

Ah, you'll be on 64dp there, I'm on 48 :( Thanks for looking anyway.
I'll have a look through my box to see what parts I have, take it your not interested in them being new?
Looks like that'll make a nice car, lots of aftermarket parts. :)

G

[Medders]

it'd be a nice vintage car if I knew what the hell happened to the rear end. :D

64dp rings a bell. Looked through the last box and nothing suitable. Sorry I can't help.

Do you still race the ProCat competitively ??

[Northy]

Hi, no problem about the spurs, thanks for looking.

I see your in the North East from your posts in the Batley section. I do race the ProCat competitively, but only in the Vintage Championship Series that we have set up to run at York Off Road Car Club. It is the second round of the championship this Saturday night if you can make it over.

Where do you actually live if Batley is your local?

Cheers,

G

[Gayo]

Hey guys, try to contact Christophe Blandin of Select Models in Lyon, France : c.blandin[at]selectmodelsshop.com. He used to have pretty old and good stuff, and he (tries to) speak some english, just like me :confused:

[Medders]

Hi, no problem about the spurs, thanks for looking.

I see your in the North East from your posts in the Batley section. I do race the ProCat competitively, but only in the Vintage Championship Series that we have set up to run at York Off Road Car Club. It is the second round of the championship this Saturday night if you can make it over.

Where do you actually live if Batley is your local?

Cheers,

G

I'm in north Leeds, so York is certainly within travelling distance. PM me the details of the meeting and I'll try to make it along. I'll bring the CAT so you can laugh at the condition its in !!

[Northy]

Details here:

http://www.oople.com/forums/showthread.php?t=1201

http://www.oople.com/forums/showthread.php?t=1820

http://www.oople.com/forums/showthread.php?t=1844

But basically doors open at 6pm, we set up the track then race. Usually a fairly decent turn out.

G

[TRIOXER]

G i believe i have what you require 85tooth 48dp.what is diameter of central hole

[Northy]

Hi TRIOXER,

The hole measures at 6.35mm or 1/4 inch.

Can you get one to me for Saturday do you think?

Cheers,

G

[daz_75]

Got some old spur gears on our website, not sure if they are old enough though, any ideas on the part numbers?

http://www.chapelradiocontrol.com/shop/retro-kits-c-52_111.html

[thaking]

hi, i got this for sale take a look
http://www.oople.com/forums/showthread.php?t=5965

Stein