CAT SX FRONT BRACE [Archive] - oOple.com Forums

stegger

07-05-2009, 09:17 AM

So i can gauge interest i'm looking at how many people would be interested in purchasing a front brace to protect the front hinge pins and blocks ?
The more people that want one the cheeper it will be :thumbsup:
Let me know. The first brace will be for the 2mm front and rear track spacers, if any other size's are required again let me know. :)
Regards steve brew

carlin

07-05-2009, 09:51 AM

:thumbsup:So i can gauge interest i'm looking at how many people would be interested in purchasing a front brace to protect the front hinge pins and blocks ?
The more people that want one the cheeper it will be :thumbsup:
Let me know. The first brace will be for the 2mm front and rear track spacers, if any other size's are required again let me know. :)
Regards steve brew

I be very interested.

Sick of buying more screws & replacing the 10Deg Blocks gone through 3 sets now :mad:
I know my driving wont help but alloy is pants very soft compound bends to easy.
So i def be up for one STEGGER:thumbsup:

MAKE IT TWO FOR ME INSTEAD BUDDY

Losi_110

07-05-2009, 09:51 AM

could well be interested, what are they made of? I'm guessing it'd need a mod to the front bumper. How much were you thinking for one?

Bomberpilot

07-05-2009, 10:39 AM

Yes, want one too, for 2mm shims on each side is ok.

Greetings

Maurice

stegger

07-05-2009, 12:23 PM

:thumbsup:

I be very interested.

Sick of buying more screws & replacing the 10Deg Blocks gone through 3 sets now :mad:
I know my driving wont help but alloy is pants very soft compound bends to easy.
So i def be up for one STEGGER:thumbsup:
Same here carlin. Just cost me £30 to replace pins and blocks and don't get me started on screws, northy must be a millionaire:p

stegger

07-05-2009, 12:25 PM

could well be interested, what are they made of? I'm guessing it'd need a mod to the front bumper. How much were you thinking for one?

I'm hoping for around about £10. But you will have to dremmel some material from the bumper.

Chrislong

07-05-2009, 12:39 PM

panch

07-05-2009, 01:10 PM

Stegger..

Put me down for two also please..

PM me when you need paying :thumbsup:

Cheers

Lee

stegger

07-05-2009, 01:14 PM

Dude, I want two asap!!!!!

Just to remind all, when fitting one of these, it is well worth replacing screws, blocks and hinge pins. It'll give the brace a better chance of lining up, and then the brace ought to keep it alligned.
You took the words out of mouth chris :) including the spacers which bend aswell. I've done this to get the proper spec's :thumbsup:

wouter.z

07-05-2009, 05:33 PM

I want 1!!! I havent have any problems myself, but i have seen damage on the hingpin blocks on Stefkes car, so I will need 1 in the future.

leon morrell

07-05-2009, 06:03 PM

yeah f**k it ill have 2 :)

ice-nine

07-05-2009, 06:23 PM

I'll take 1, possibly two. :thumbsup:

Steve

07-05-2009, 08:42 PM

Sounds like the one we had on our 24hr car made by nortec

Ian F

07-05-2009, 09:00 PM

1 for me please:thumbsup:

stegger

07-05-2009, 09:06 PM

Sounds like the one we had on our 24hr car made by nortec

;);)

stegger

08-05-2009, 08:55 AM

could well be interested, what are they made of? I'm guessing it'd need a mod to the front bumper. How much were you thinking for one?

Made from grade 5251 mate, has good anodizing properties too. ;)
I will have one at the latest tuesday night :thumbsup: And i can confirm a price of £9.99 plus p&p. :drool:
Regards steve brew

stefke

08-05-2009, 09:25 AM

I want 1!!! I havent have any problems myself, but i have seen damage on the hingpin blocks on Stefkes car, so I will need 1 in the future.

As he said, already ruined two sets of blocks. Astro tracks are real killers for those blocks. I'll take two !!!!

ThePromise

08-05-2009, 09:36 AM

Made from grade 5251 mate, has good anodizing properties too. ;)
I will have one at the latest tuesday night :thumbsup: And i can confirm a price of £9.99 plus p&p. :drool:
Regards steve brew

I would go for two sets...let me know when available....

Greets, Chris

rc10fan

08-05-2009, 01:01 PM

count me in please i will have 2 also asap please:) I spoke to phil as schumacher about 3 weeks ago and me mentioned trying to sort out a brace of some sort of they had time. My wallet wont wait much longer if i keep on bending these damn things.

MHeadling

08-05-2009, 01:05 PM

Hi,I'll have one please! PM me when you want paying.

jayst

08-05-2009, 03:58 PM

ill have 2 . could we have a pic of it fitted

ice-nine

09-05-2009, 07:27 AM

Scratch me off the list, going 1/8 electric, the only 1/10 offroad racing in my area if on the one day I can't change my schedule to get off. :thumbdown:

AmiSMB

11-05-2009, 03:33 PM

I am interested in a couple of these. Have you got any pictures ready of them?

jas_racing

11-05-2009, 09:01 PM

One here please :drool:

stegger

12-05-2009, 07:01 AM

Just to keep everyone up to date, i should be getting the first brace tonight and if its ok the rest of them will be made up towards the end of the week :thumbsup:

All PM's answered:)

Carlos69

12-05-2009, 09:16 AM

I'll take one !!! pm 2 follow

carlin

12-05-2009, 03:49 PM

Are we going to see some PICS TOO :thumbsup:

stegger

12-05-2009, 04:13 PM

Yes at the latest tomorrow :thumbsup: i will see the first one tonight and it fits o.k will post pics :)

stegger

12-05-2009, 10:17 PM

Sorry for the quality of the pictures but you can get the jist. The top and bottom lips are going to be reduced slightly so it doesn't hit the bulkhead and to reduce the amount of material to be taken of the bumper but that's the only changers that will be made. They will be made up sometime this week at the latest tuesday the 19TH. :thumbsup:

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_FRONT.jpg

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_SIDE.jpg

I've left the rear nuts off the hinge pin which can bind up the suspension as standard. :thumbsup:
It also makes it easier to remove the suspension if needed by just unscrewing the hinge pin. :thumbsup:

Thanks for looking. :thumbsup:

Regards steve brew

Siggy

13-05-2009, 04:17 AM

I'll take 1.:thumbsup:

PaulUpton

13-05-2009, 06:29 AM

stegger

13-05-2009, 07:51 AM

Looks well made, but can't see wat you are gaining other than stopping ripping the screws out, screws are still going to bend, and the rear wishbone hangers I would say are more prone now as you have more leverage from both sides not just one!

Hello paul thanks for the compliment :thumbsup:
From experience it's mainly been the front 10* block and screws that have bent and crushed, making the front spread out and causing the rear blocks and screws to do the same because of the leverage. This brace will stop that ;)

PaulUpton

13-05-2009, 11:16 AM

not had any problems with the front blocks, plenty of screws though!

If you can design something that stops the rear blocks from snapping, ill have one! lol

stegger

13-05-2009, 11:49 AM

not had any problems with the front blocks, plenty of screws though!

If you can design something that stops the rear blocks from snapping, ill have one! lol
Rear blocks on the front suspension or rear suspension paul ? do you have a picture of what happens ?

B&H Racing

13-05-2009, 12:07 PM

Can I have one please Steg !!! :D

James

13-05-2009, 12:45 PM

Could i have 2 please?

:)

Chrislong

13-05-2009, 01:05 PM

Hi Paul,
The rear front-wishbone blocks break because of the sliding motion of the wishbone going back on an impact, so if you have the nut on there loose and the front block is tightened and screw not bent, it should stop this - although many of us, me included, don't run the nut as it does tend to tighten and bind the wishbone up.

So perhaps threadlock the nut on loosely.

Ive snapped 2 of these, both times in big crashes - hitting stationary car on the straight at full speed. But both times ive also broken a wishbone, severely bent the screw and crippled the front block too, also the pin bent. So unavoidable/expected damage.

With the front block tight, this new brace on, and nut loosely on the back the rear block should be as safe as it can be I reckon.

Come on Steve, send me my braces, im dieing to run these.... :thumbsup:

stegger

13-05-2009, 01:36 PM

If everyone can wait just a little bit longer i should have these within a week. :thumbsup:

paul01ews

14-05-2009, 06:49 AM

Two for me please, just pm me your payment details when your ready

Paul.:)

stegger

14-05-2009, 07:37 AM

All pm's replied too :thumbsup:

ben

14-05-2009, 02:39 PM

Why do most people want 2? :blush:

jimmy

14-05-2009, 02:43 PM

Helliwell and Long both have 2 cars because they are TEAM :thumbsup:

Northy

14-05-2009, 02:48 PM

I also have a "brace" of cars :woot::woot:

And they are all braced up :thumbsup:

G

stegger

14-05-2009, 02:53 PM

Why do most people want 2? :blush:
SHUT UP ben think of the money :woot:

restimax

14-05-2009, 10:00 PM

good work stegger!!!

ThePromise

16-05-2009, 12:37 PM

I am interested in a couple of these. Have you got any pictures ready of them?

Hey there, any news concerning payment and delivery?

Best, Chris

stegger

16-05-2009, 04:06 PM

I will post details in the next couple of days. :thumbsup:

stegger

19-05-2009, 10:54 PM

:thumbsup::thumbsup::thumbsup:GOOD NEWS GUY'S :thumbsup::thumbsup::thumbsup:

I am now taking orders for the cat 2mm track brace please pm your details for postage etc and i will forward PAYPAL details

Here's the first one fitted to my car.

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_0013.jpg

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_0014.jpg

This is with bumper fitted, you do have to take a bit off the bumper but with a bit more fettling it will fit better.:woot:

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_0010.jpg

http://i12.photobucket.com/albums/a207/cheshiremodelcars/IMG_0015.jpg

This was a quick fit but with a bit more care you could make it neater.
Looking forward to hearing from all interested parties. :thumbsup:
Regards steve brew....

Chrislong

20-05-2009, 09:38 AM

Looks cool, good work Ste... :thumbsup:

stegger

20-05-2009, 11:51 AM

Cheers chris :thumbsup: All other pm's answered :) will be posting braces tomorrow morning:thumbsup:
Regards steve brew.

stegger

20-05-2009, 09:04 PM

Thanks for all the orders guy's :thumbsup: all orders are processed and will be sent out tomorrow :thumbsup:
Thanks again steve

Siggy

21-05-2009, 05:52 AM

Payment sent. THANKS MATE! :thumbsup:

stegger

21-05-2009, 06:53 AM

Payment sent. THANKS MATE! :thumbsup:

Our first international order :thumbsup: thanks siggy :) it's in the post this morning.

Lee

21-05-2009, 06:13 PM

I saw Steve's brace at the weekend and it looks really smart, simple yet effective and really good quality :thumbsup:

stegger

22-05-2009, 07:16 AM

Thanks Lee :thumbsup: For those of you that receive your braces today !!!! REMEMBER !!!! for best results use new inner hingepins and blocks. You may get away with your old ones, but mine were bent well out of shape:o:o We have also made them so the thread of the hingepin cuts the brace hole ;) The hingepins should be tight enough that you will not need the rear lock nut and washer, which also has the added benefit of not destroying your chassis and not binding up the suspension.
Hope everyone likes this product and good luck :)
Regards steve brew.

Chrislong

23-05-2009, 07:02 PM

Got the braces on both my cars now, excellent work Steve.

When fitting, note to all: Loosen the M3 screws into the gearbox sides, and tighten them once the brace is on tightly... just makes things easier and line up with less chance of stress if anything is going to be stressed at all.

The other thing, the bumper mod is easy, just use a cutting disk on a dremel and take out a section immediately above the holes in the bumper exactly like Steve has done. I did mine really close to the screw holes as it needs to be, if not close enough then the bumper holes don't line up to the gearbox holes.

Oh, and I did try my first bumper mod with the small sanding drum, and it doesn't work. I shouldn't be so lazy and found the cutting disk. By using the drum I also reduced the depth of the screw holes in the bumper a little and although it'll be okay, its not as good as using a cutting disk and leaving the depth of the holes alone.

Good work Steve, fitting time about 5minutes once I stopped being lazy and used the cutting disk on the dremel. :lol:

Chrislong

24-05-2009, 04:00 PM

Ran both my cars today, and gave them both plenty of abuse - the front screws and alloy blocks are as new...

I had to go find a shock in one qualifier, and in the final I crashed at the start quite hard, one corner was 6ft up in the bush at the end of the straight at Bury.... still all is good apart from wishbone, the hinge pin screw bent upwards only, so all it needs is hinge pin and wishbone.

Good work Steve... highly recommend this item

stegger

25-05-2009, 11:05 AM

Thanks for the feed back chris :thumbsup: there's nothing like a proper racer to test items like this :)

Chrislong

25-05-2009, 08:49 PM

I certainly crash tested them :lol:

Siggy

27-05-2009, 06:40 AM

Got it in the mail today! Real nice looking piece and an easy install as it fits perfect. Thanks!!!:thumbsup:

stegger

27-05-2009, 09:26 AM

Glad you like it SIGGY :thumbsup:
Anybody at OZ on saturday who would like a brace. I will be there watching the racing, so if you want to save on postage and you see the braces on some of the cars and you like what you see.
Let me know on here and i can meet you. :)

Cassp0nk

27-05-2009, 11:40 AM

Could a brace not be designed that fitted over the bumper rather than having to mod it?

stegger

27-05-2009, 02:18 PM

Could a brace not be designed that fitted over the bumper rather than having to mod it?

I was thinking this also before i had this brace made and was told it would cost to much to make. :(
For the sake of cutting a bit out of the bumper its good to keep it simple. :)

Chrislong

27-05-2009, 02:48 PM

straight lines are strongest, this part needs to be strong otherwise it'd be a waste of time. This brace is perfect just as it is. :thumbsup:

Swiss

03-06-2009, 09:04 PM

Hi Stegger

I am looking to get hold of one for the weekend. I can paypal asap. Do you have any in stock?

Thanks

Paul

stegger

03-06-2009, 09:06 PM

Paul you have a pm fella:thumbsup:

restimax

03-06-2009, 09:17 PM

next month i want one...:lol:

Karel

03-06-2009, 09:49 PM

How does it look?
Do you have a photo?
Can you send it to Czech Republic as well?
Do you have a PAY PAL, or how can I pay to you?
Thanks
Karel

Chrislong

03-06-2009, 10:08 PM

It looks factory as long as you dremel the bumper neatly. You need one of these asap, it'll save a lot of time and money in replacing screws and blocks... :thumbsup:

stegger

04-06-2009, 07:24 AM

How does it look?
Do you have a photo?
Can you send it to Czech Republic as well?
Do you have a PAY PAL, or how can I pay to you?
Thanks
Karel
Hello karel yes i can send to the czech republic :)
Look at the photo's in this thread and you can see how it's mounted and what you have to do to modify the bumper, yes i do take paypal just pm me for details. :thumbsup:
Regards steve brew

Swiss

04-06-2009, 07:12 PM

I presume from the photo's it's designed to be used with two washers under the w/bone hangers?

P

Swiss

04-06-2009, 08:19 PM

stegger you have a pm.

Northy

04-06-2009, 08:26 PM

Paul, 2mm washers are needed under each front brace.

G

Swiss

04-06-2009, 08:28 PM

Thanks Graham, I am also interested in a 1mm spacer one.

P

Cassp0nk

05-06-2009, 12:01 AM

I was thinking this also before i had this brace made and was told it would cost to much to make. :(
For the sake of cutting a bit out of the bumper its good to keep it simple. :)

I wasn't thinking of anything complex, simply having a cut away to allow it to pass over the bumper with more metal below. So it would still be flat but more like :
o_o

than

o-o

i.e. more U shaped if that makes sense. (p.s. imagine the line is thicker than that I'm just trying to give an impression).

Anyway nice work on what you've done already :) I just don't want to dremel as I'm concerned it will create gaps that will let dirt in.

Hopefully schumacher are working on a fix themselves.

Kusal

07-06-2009, 06:58 PM

Stegger,
I also want one if you still have stock. I live in Belgium and have Paypal. Pm we with the details on costs and I make the transfer asap.
Thanks,:thumbsup:
Kusal

stegger

10-06-2009, 06:55 AM

Just to let people know i only have LIMITED STOCK of this item so if you need one pm or e-mail me as soon as you can. THANKS for your support :thumbsup:

restimax

10-06-2009, 07:36 AM

i have send you a p.m.
;)

restimax

10-06-2009, 08:01 AM

ok, payment send

Swiss

11-06-2009, 03:52 PM

Steve

Any news on the 1mm Brace. You have a pm.

Thanks

Paul

stegger

11-06-2009, 04:38 PM

pm'd back fella.

Anybody else interested in a 1mm track brace, there must be more than 1 wanting one. ;)

Chrislong

11-06-2009, 06:32 PM

Not me pal.

Kusal

12-06-2009, 11:34 AM

Stegger,

I assume you have received my Paypal payment.

Kurt Sallaerts

stegger

12-06-2009, 03:13 PM

Stegger,

I assume you have received my Paypal payment.

Kurt Sallaerts

Yes mate sorry (been very busy) and the brace was posted yesterday morning mate :thumbsup:

Kusal

12-06-2009, 10:52 PM

No problemo :thumbsup:

Thanks for the brace!

deepdale11

13-06-2009, 10:21 AM

Can i order one please!!

stegger

13-06-2009, 03:34 PM

Can i order one please!!

PM'd fella :thumbsup:

Chrislong

13-06-2009, 08:27 PM

:blush: Steve, I need another brace dude...

I hit a kerb flat out, and it ripped the car to shreds. But testiment to the brace, it didn't let the pivot pin splay out and therefore saved the purple blocks..... what I did to though is bend the hing pin screws, sheer two screw heads off and turn the Alloy brace into a 'Z'...

Ive now fitted a new front end to the Cat, with M4 front screws, and using another Brace (thankfully I got another off you at Ozfest) :thumbsup:

So yeh, highly recommend. The nature of the alloy bending is perfect - could have been a lot worse than it was for me.

stegger

14-06-2009, 09:25 AM

You animal :lol::lol::lol: if you haven't got my details chris PM me

stegger

25-06-2009, 07:32 AM

Down to a hand full of 2mm braces chaps ;) until i get new stock in a couple of weeks were the 1mm brace will make an apperance. Other stuff for the Cat SX in the pipe line as well :drool: keep tuned.
BW-RACING@HOTMAIL.COM

bigred5765

28-06-2009, 09:42 PM

hey up steg looks like were going to need one of these bad boys,pm us details please

Chrislong

28-06-2009, 10:05 PM

Carl, carry 2 ;) They are made of Alloy which is ideal as it allows some flex and give without the screw bending, but without limiting anything else, but in a large impact (ive had many LOL) they do twist and bend while saving other more expensive items. ;)

stegger

29-06-2009, 07:08 AM

Bigred , you could have had it off me yesterday, i walked right past yeh when it was raining going back to my car with the Mrs :o You have a pm fella.

stegger

04-07-2009, 03:49 PM

Limited amount back in stock of the 2mm brace :)
1mm and 2mm in stock very soon :thumbsup:

stegger

16-07-2009, 04:11 PM

2mm & 1mm braces will be in stock pm tomorrow.

£10 each or special price of £17 for 2mm and a 1mm brace.
I will be at southport on the saturday and sunday afternoons, somewhere near the schumacher team tent or pm me on here or email me at BW-RACING@HOTMAIL.COM

Regards steve brew :)

Chrislong

16-07-2009, 04:45 PM

See you at the weekend Steve!! :)

When will you have some team clothing???? ;)

stegger

16-09-2009, 06:52 AM

Please can people supply the correct postal address and discription of what they want when contacting me ;);) it means you get your stuff a bit quicker. :thumbsup:

rob84

24-12-2009, 04:41 PM

just fitted the 1mm brace to my car,, i have used a 1mm washer on both side on the inner side to. the wishbones have gone really stiff. dnt suppose this is suppose to happen do i need to shim it out? cheers

stegger

25-12-2009, 10:55 AM

Make sure that you fit with NEW blocks, if you have been using the car without a brace, chances are they could be slightly out of shape and the hinge pin could also be bent ;) After you fit your brace leave OFF the backing nut and washer at the back of the front hingepin and then tighten up the block screws to let everything square up.
Happy Christmas to yeh and all our BW-RACING customers :thumbsup:

Kusal

11-01-2010, 10:36 PM

Hi Stegger,
I would like to order two 1 mm braces.
I have PayPal.
Let me know what to do.
Thanks:thumbsup:
Kusal

Cobra427

15-01-2010, 05:46 PM

Hi, I would like to buy one, could you PM me with your details, can pay by PayPal

fido-dido

20-01-2010, 08:27 AM

how do i order? ?

jono83

20-01-2010, 12:22 PM

PM "STEGGER" on here he will sort you out

fido-dido

20-01-2010, 02:55 PM

i have twice, maybe he's been on holiday

David Church

20-01-2010, 08:11 PM

Keep on trying, this is a thing he does after his normal work!! He will get your message eventually:thumbsup:

AmiSMB

20-01-2010, 10:15 PM

I have one of these brand new (2mm track version) in packet which I can do for £6 including postage. PM me if interested.

stegger

29-01-2010, 11:56 AM

Fido, down boy:lol: i've pm'd you fella. I'm still taking orders and have 1mm and 2mm braces in stock. But only have 2 layshafts in stock ;) after they go i will only be getting them to order on an individual basis.
Steve
BW-RACING@HOTMAIL.COM

stegger

02-03-2010, 02:08 PM

Could somebody do me a favour and let me know if the BW-RACING front brace will fit the SXII when it comes out. :thumbsup:

bigred5765

02-03-2010, 03:49 PM

cant see why not not geometry changes

armadillo250

11-03-2010, 01:50 PM

Hi Stegger

Have you managed to post my 2mm brace yet mate?

stegger

11-03-2010, 09:24 PM

It's coming out to you tomorrow mate :thumbsup:

PsycoChris

15-03-2010, 12:40 AM

Hello sir. How much are these? I made Mine with Carbon Plate. But would like one of these also. Seems like this is the way to go. Wish they would make this all a 1 peice design. I bent more screws on this than anything.:cry:

moth898

15-03-2010, 02:53 AM

Stegger's braces are the way to go for the front end, I'm waiting for mine to arrive soon. Shumacher has also addressed this issue by making a thicker front pivot block using a 4mm screw instead of the 3mm, but you have to change the front lower transmision half to accept the bigger screw. Stegger's brace is the most cost efficient fix.

moth898

04-05-2010, 01:06 PM

Exellent service from Stegger....A1 fella!!

stegger

26-05-2010, 04:29 PM

For all those lucky people with the SXII i'm still making the front braces in 1mm and 2mm configurations. :drool: I am also still modifying the SX and SXII layshafts so you can use losi and team associated spur gears ;)
You can also do this with the Cougar layshafts ;);)
Braces = £10.00 each or £17.00 for a 1mm and 2mm kit
Layshafts = £15.00 only by special order
P&P = £1.50 UK, £2.00 europe or £3.00 ROW

Paypal gift to BW-RACING@HOTMAIL.COM

:thumbsup::thumbsup::thumbsup::thumbsup::thumbsup:

gazhillAE

04-06-2010, 08:13 AM

Sounds good !
Might be a daft question but what are the differences on the car for the 1mm and 2mm wersio why build both?

Whats also included in doing the layshafts and is that a new one supplied or do you need mine on a return basis?

Gaz

frogger

04-06-2010, 09:33 AM

The 1 and 2 relates to how many spacers you use on the steering blocks. If you use 1mm spacers then you use the 1mm brace, etc. For a stock Cat you will need the 1mm brace.

stegger

07-09-2010, 09:10 PM

God, haven't been on here for a while :cry: Just to let everyone know i've ran out of the 1mm braces :o (not sure if i will be able to get anymore)
I still have plenty of the 2mm braces but once they go like the 1mm, when they go there will be no more. And i have 1 modified layshaft left ;)
Thankyou to everyone who has bought from me over the last 12 months, will see you soon.
Steve

schmacher

08-09-2010, 02:31 AM

hey stegger, do you ship to the U.S. ?

stegger

12-09-2010, 02:58 PM

hey stegger, do you ship to the U.S. ?

Everywhere in the world fella, even the U.S :p

stegger

23-10-2010, 05:56 PM

Limited amount left of the 2mm braces :thumbsup: Once they have gone there will be no more ;)
Price has been reduced too clear so be quick.
£8.50 inc free postage in the UK, ROW add £1.00

PM me to order.
Regards steve :)

stegger

29-10-2010, 07:27 AM

All remaining order's being sent out today. :thumbsup:

There are only 12 x 2mm braces left so if you want one of these bad boy's you will have to be quick. Remember there will be know more after these go. ;)

stegger

31-10-2010, 09:09 PM

Only 10 left now :thumbsup:

Big G

31-10-2010, 10:06 PM

My cat came with this brace on it and it's never been removed until today when I widened the track on the front. What do you know... 1 of my blocks stripped the thread from a small knock on a track marker. 100% sure this wouldn't have happened with the brace installed.

stegger

01-11-2010, 09:25 PM