db01 rear arms

[Rozzy]

any 1 else having the problem of the rear hinge popping off on some jumps ive had this problem from when i got the car and ive seen another car do the same thing is there a way to stop this happining??

[DCM]

you got two options here.

1) Shim the hingepin tight, this will top the pins from popping, mainly.

2) Buy the allow pin mounting brackets.

[Rozzy]

how do the alloy parts help??

[T4miy4 Guy]

I`ve never had this problem, i have the alloy bits fitted

http://cgi.ebay.co.uk/3Racing-Tamiya-DB01-Alum-Motor-F-R-Suspension-Mount_W0QQitemZ390053365264QQcmdZViewItemQQptZRadi o_Control_Parts_Accessories?hash=item5ad0fe0610&_trksid=p4634.c0.m14.l1262

http://cgi.ebay.co.uk/Tamiya-53709-Fluorine-Coated-Suspension-Balls-8-Pcs_W0QQitemZ380134001984QQcmdZViewItemQQptZUK_Toy sGames_RadioControlled_JN?hash=item5881c08d40&_trksid=p3286.c0.m14

Hope this helps

Andy

[fabolousRC]

Also, if you are on the (low) budget, you can replace those suspension mounts with the carbon reinforced ones (M parts #54036 such as this (http://www.vellrip.com/store/product_details.asp?p=1501&c=47)) and replace the suspension balls and inner suspension blocks with the carbon version on the A parts (#54033). I bought and installed my alu pieces before I realized there are cheaper alternatives to it.

[F1END]

I am on a tight budget and I have the alloys on the front and the carbon-reinforced ones on the back. Had to get a new lot of A-parts anyway for the diff-covers, so figured I may as well get the carbon ones and changed those bits too. Hasn't happened to me since. When I have more money, I'm gonna get the alloys for the back too, but I'd rather save up and get some trf dampers first.

The problem with the kit bits is that they are soft and flexible, so they 'give' and the ball pops out. The alloys (and to some extent, the carbon-reinforced ones) flex less and don't give, so the ball stays in.

[F1END]

Might want to ignore my advice about the Carbon Reinforced bits, and just stick to the alloy bits... mine popped out about 5 times this weekend :thumbdown:

[suparajicon]

Weren't the screws loose? Where all the washers correctly placed? Did you use that grease the manual says? I think this grease would help the hinge pins to pop out easier. I haven't put any of this grease and I have had no problem so far. Maybe I am just lucky .. I am not a big fun of spending my money in aluminium parts, I would have bought the TRF instead if I had wanted aluminium.

[Rozzy]

ive shown mine to a friend that works in a hobby shop and we modified it a little now has metal ends balls from a asserted car witch in name alone will make it faster :lol::lol: ill ty it out 2night getting tamiya parts in australia is very hard the distributer should be fired as they only bring in he cheap end of tamyas stock anything cose to TRF range and ill have to get it from RCMart so its normaly over a week till i get it

[suparajicon]

After reading your post 3 times I understood it. :thumbsup:

[VinceVegaUK]

My rear tore off after hitting a home made ramp wrong, i dont blame the car more my stupid idea and crap driving. In some ways these parts are supposed to break and pop off as less stress goes through the expensive bits. I did upgrade to the carbon reinforced set it only cost me £20 from Tonys Tamiya parts for A&B parts tree and new diff cups. My shock are the only things that pop off when i race but i have just upgraded to the aerated options damper that screw in rather than the ball joint, they also work now unlike the not so good plastic ones.

I mainly use Vellrip, in singapore and he ships worldwide, RCMart are ok but they take a while to ship. I usually order from vellrip on a Thursday night/friday morning if i have broken somthing on Thursday evening racing and every single order always comes the following Wednesday. good prices too and he stocks most Tamiya parts inc DB01 and the 501x.

Also try Tony's Tamiya Parts on ebay he's UK based and very good for most things and posts quick too.

http://www.vellrip.com/store/home.asp

later

VV