PDA

View Full Version : t peice

bondy
22-10-2009, 03:42 PM
any news on the T peice if so I might give one a go !:thumbsup:
rc_dan
22-10-2009, 03:49 PM
from what i have gathered on here the new t's are thicker ;)
stampede vxlboy
22-10-2009, 04:17 PM
you should of got a steel 1 of paul when he had them he had loads ask him to give you the shops he sold them to denmark i think
Benjab
22-10-2009, 04:34 PM
Denmark :D? Im from Denmark. Ive only seen one shop that sells madrats
stampede vxlboy
22-10-2009, 05:05 PM
i had a link for them pm paul he mite send you it
ConceptRacing
22-10-2009, 06:02 PM
AnswerRC now stock the alloy T pieces so I believe
Battle_axe
22-10-2009, 06:50 PM
AnswerRC now stock the alloy T pieces so I believe
i have been told these are rubbish as they bend so badly

the new plastic one is good though its strong i have not broke a new one yet
stampede vxlboy
22-10-2009, 07:30 PM
pm paul ask him which shop he sold all is to i know it was in denmark
Answer-RC-Pete
22-10-2009, 08:02 PM
Been told they are rubbish? An alloy one would be, thats why we dont have one and never made one!

Watch this space though for some upgraded ones which are better than alloy.....
stampede vxlboy
22-10-2009, 08:20 PM
alloys bit for the madrat cant wait
Jony P
22-10-2009, 09:42 PM
iv'e just got an x pro and it's FAB!!

can't imagine why you would want a steel t piece though??:confused:
i found i needed more wieght in the front 1/4 of the car so i got the carbon fibre t piece and the new brass bulkhead (which i must say is an amazing idea with the weight you can put in and out from track to track)

also i put 20grams in both front pods to generate more side bite/roll through a corner.
stampede vxlboy
22-10-2009, 09:49 PM
they just snap for fun i had a carbon 1 that snaped and the steel 1 are ace and get rear pin holders under the tplat they all snap the plastic not that strong
and get a brass battery tray £19,99
rear pin holder £17.48alloy under the tplate
rc_dan
22-10-2009, 09:52 PM
ent snapped a t yet, must not be driving it hard enuff :blush:
stampede vxlboy
22-10-2009, 10:00 PM
i had 2 tplate plastic if it does not land right they just snaps and a carbon than just snaped for fun as well. hit the power and you will see dan
jim76
22-10-2009, 10:00 PM
they just snap for fun i had a carbon 1 that snaped and the steel 1 are ace and get rear pin holders under the tplat they all snap the plastic not that strong
and get a brass battery tray £19,99
rear pin holder £17.48alloy under the tplate

don't get a brass battery tray if you have a madrat, as it won't fit with a 23mm deep lipo. you cannot get the battery strap on. Not sure if the X pro has adjustable height battery posts or not, in which case it would be ok, but for the madrat it is no good unless you have VERY thin lipos.
rc_dan
22-10-2009, 10:16 PM
i seen a smart brass plate for on top of the servo made by trish bits i think

40grams if i remember right £7.99 any one got one of these ? 40 grams make much affect guys ?
jim76
22-10-2009, 10:22 PM
i would just buy a pack of adhesive lead weights, you can get 200g for the same money
rc_dan
22-10-2009, 10:24 PM
true, is a bit posh tho ay

cheers bud
Paulmay79
23-10-2009, 09:21 AM
Contact answer rc pete or jmsjms for stainless t's
Paulmay79
23-10-2009, 09:23 AM
iv'e just got an x pro and it's FAB!!

can't imagine why you would want a steel t piece though??:confused:
i found i needed more wieght in the front 1/4 of the car so i got the carbon fibre t piece and the new brass bulkhead (which i must say is an amazing idea with the weight you can put in and out from track to track)

also i put 20grams in both front pods to generate more side bite/roll through a corner.

The steel t is a must if you drive it hard. Its only 45g in total.
stampede vxlboy
23-10-2009, 10:59 AM
well said paul the tplate are ace all your bits you made are mint:thumbsup:better than alot of the alloy stuff. and your stuff is strong