b4 diff and drive shaft must be good condition

[stampede vxlboy]

hi need some good drive shaft and a good diff that the cups on the outer are black not silver were the drive shaft go to the wheels my drive shaft dont fit in the rear caster right

[jim76]

double post? you already have this in the wanted section?

[stampede vxlboy]

i know its worth a try

[sparrow.2]

hi need some good drive shaft and a good diff that the cups on the outer are black not silver were the drive shaft go to the wheels my drive shaft dont fit in the rear caster right

Take a deep breath and rephrase. That makes no sense whatsoever...

[stampede vxlboy]

sorry need some new ish drive shafts and a good diff is that better mate
as my cups of my diff are silver and looks worn and the drive shaft dont fit into the rear caster right were the wheels go

[jim76]

check your rear hub bearings then, they may be worn and very wobbly.

[stampede vxlboy]

i can move the rear caster with my hands and move the drive shafts
do the drive shaft fit into the reae hubs our do they look like they dont go in all the way i just priced all the parts new diff drive shaftdiff hubs diff ring and these other aparts 7677 ,9597,9755 £55 for the lot

[Darren Boyle]

You can buy a complete and entire diff for the B4 now for less than £40 if it is that bad....

[stampede vxlboy]

pm you about prices for my b4 parts

[stampede vxlboy]

got most of the parts for my spare b4 that i am keeping and 1 forsale

[Tom3012]

So you want the factory team diff halves/outdrives as apposed to the normal ones... and you need some new hubs and bearings.. CVD bones...

i make that to be...

£26.23...

AS7668
AS7667
AS9597
AS9584

[stampede vxlboy]

parts 6581
7677
7667
7668
9584
9597
9688 wheels
9689 wheels
6588 and pins for the drive shaft i got told to buy all these parts do i need them all are the diff hubs on the diff silver and the drive shaft look like they dont fit in the rear huds right

[Tom3012]

If you could post some pics of what you mean when you say they dont fit that would be a great help?

Or what about...

290346741831

[stampede vxlboy]

give me 5 mins and i will put picture up

[stampede vxlboy]

pictures of the drive shaft and diff and rear hubs,the drive shafts dont fit in the hubs right they stick out .and i can pull the shafts by hand

[sparrow.2]

What is the problem? Looks fine to me.

Whoever sold you the car was kind enough to leave a set of MIP shiny bones on it. Rather nice of them. Make sure you have the silver spacer on the right way round with the conical side towards the bearing.

You will not notice a difference between the factory team outputs and the regular team car ones! you might also need a couple of spacers on the inside of the hub too but nothing major.

Can you drive the car at the moment or what is the problem exactly which you would need to toss that much cash at???

[jim76]

the problem is he has no idea how his car is meant to be built and is obsessed with buying unnecessary parts to fix things that aren't wrong!

[stampede vxlboy]

rear hubs are wearing away and the pins for the wheels are bent and the waster round side faces the outside toward the wheels and were can i get get alloy blue screw and nut for the shocks

[stampede vxlboy]

what size are the bearing for the back wheels any parts number for blue alloy nuts and bolts for the shocks and bearing and spacer in the hubs not the round dis c were the pins sit for the wheels

[sparrow.2]

Reread my post FFS!

Your wheel spacers are on the wrong way round! That is why your hubs are wearing and your drive pins are bending.

Read the bloody manual!

Do not attach the shocks with aluminium screws!!! There is a reason noone does this. Because it doesn't work and the screws bend and break.

Run the car and don't glitz it up like a cheap hooker...

[jhammond]

Honestly... If you're short on money, don't waste it on shiny things.

Unless something fails, is very likely to fail or drastically affects performance, then it does not need to be replaced.


Visit your local club; I'm sure they'll inform you that there's little or no problem with your B4. Also, if there's some play, you can always shim it out. This is common practice and wear is an expected result of use.

Julius.

[jim76]

Reread my post FFS!

Your wheel spacers are on the wrong way round! That is why your hubs are wearing and your drive pins are bending.

Read the bloody manual!

Do not attach the shocks with aluminium screws!!! There is a reason noone does this. Because it doesn't work and the screws bend and break.

Run the car and don't glitz it up like a cheap hooker...

don't waste your breath. He will buy them anyway then in a weeks time he will be complaining that one has sheared and how weak and crap the B4 is and it will be up for sale (again).

[stampede vxlboy]

i am not buying them just diff balls pins for wheels waster rear hubs new shock screw and nuts and new bearing for the rear hubs and spacer

[sparrow.2]

Don't PM me again!

i got it like this i took the diff out that it and the round side of the waster is to insides of the wheels . does the flat side of the waster to wheel bending the pins any item number for shock screw and nut not plastic 1 and washer and bearing . is the round side of the waster to the inside of the hubs

If you can make sense of this yourself you deserve a medal.

You have the explanation to your problem and you can go look for your own part numbers.

Hot damn do you talk like you write too? Or do you have ADHD?

[sparrow.2]

i am not buying them just diff balls pins for wheels waster rear hubs new shock screw and nuts and new bearing for the rear hubs and spacer

Of that lot you probably only need the wheel pins...

BTW one of your motor cables looks like it's not soldered onto the motor properly!

[stampede vxlboy]

i know the wires not on there about 1 inch play on the hubs and shafts i think the bearing are worn or washer are missing were the bearing sit and should you beable to move them a lot the shafts

[sparrow.2]

You certainly do not have an inch of play in the axles!

Read this, it's good for part numbers too:

http://rcdocuments.com/file_info/download.php?file=Team_Associated_B4_Manual.pdf

[stampede vxlboy]

thanks :thumbsup: