Associated GT2 Brushless Conversion

[j.m.]

My neighbor let me have some fun with his GT2!! :woot:

Motor plate is all hand cut out of 1/8" (3mm) aluminum. Certainly not as clean as CNC, but I think it's pretty good for hand cut. The support brackets have some cleaning up to do. Ideally I would just remake them out of thicker metal so I could tap threads right into the aluminum and lose the locknuts.

Batteries will be saddle packs that slide in from the side under a top deck where the esc and Rx will be located on. The standard size steering servo will stay.

For now the motor is a crappy Chinese thing... I got bored and 'opened her up' a bit. :o

Jon

[cheapo]

Hehehe! Way to go!
Out with the Nitro in with the new. Brushless is deffffinitely what it's all about now.
Great job on the cut-outs there! Personally, I would recommend a single screw 'pivot' hole and radius slot, due to the extra power. I reckon you've built a wheelie monster there! Motor nice and high, Lipo batteries to keep the front light, job done! :cool: Put a wheelie bar on it!
I converted a Hot Bodies Lightning Stadium as soon as it arrived from good ole ebay. I've never used nitro, never will. ;)

[j.m.]

I tried to do the radius slot at first, but without a mill, it was impossible to keep the cuts clean.

That particular motor isn't too intense. It is a 540 'L' size, or ~8mm longer than most car motors, but is about even in power. My neighbor won't be racing, strictly bashing, so we might go a little bigger and do a HUGE helicopter outrunner with a spur gear for a pinion.:woot::woot:

On a side note, I don't get why the gas trannies are built so much stronger than electric. Electric cars have way more torque...:( Great transmission in the GT2 though, one of my favorites.

Jon

[Dumbstixlars]

That's pretty cool. I found this thread during a search cause I was thinking about doing this to my GT2. What pitch do you need for the pinion? 32P?

[j.m.]

Yep! 32p pinion.

Or you can use a B4 sppur. They are the same size and fitment. :woot: You'll need a fairly large pinion though...

Jon

[AJ Roberts]

Yep! 32p pinion.

Or you can use a B4 sppur. They are the same size and fitment. :woot: You'll need a fairly large pinion though...

Jon


Thought the B4 was 48dp???

[rcjunky]

Its a pretty cool project. What did you do other then remouve everything and put on a custom motor plate? Is there much to this conversion? it looks like an easy way to have a mid motor truck with out the cost of a x60, could you post pics of how the motor plate is mounted and what you did to the brake assembly please. Might try to do this

[j.m.]

Yeah, the AE electric spurs are 48dp. It's easier to find pinion gears in this size, that's why I said you can use them.



I completely removed the brake assembly!! No need for it. The motor mount goes to the tranny at the two points where the brake assembly mounted. The front end of the mount is also attached to the chassis to stiffen things up, but it's not a flexy truck by any means to begin with.

It is a pretty good alternative as long as you don't mind making battery trays n such.

Jon:thumbsup:

[j.m.]

It's blurry, but shows the tranny mounting:

[rcjunky]

I figured you got rid of the brake assembly, I don't have a gt2 so I was more curious if you could remove it like that, I guess so. Is that the stock top shaft? I'm considering doing this as my SC truck will be sold soon but we don't race trucks, maybe a custom chassis to make it an SC truck? I have access to all sorts of tools so building a motor plate on a mill wouldn't be an issue

[j.m.]

Stock top shaft, and the tranny has 4 gears.

It would make a WONDERFUL SC truck with a longer chassis. It has GREAT handling. You will definitely hinder the performance by extending the chassis, but the truck will still be a lot lower than any other around.

My original idea for a motor mount was to use a large piece of 6061 angle stock to mount the electric motor to the chassis' original nitro motor mounting holes.

I decided not to use this idea though because then a chassis stiffening brace would need to be fabbed or the original piece mangled to shreds.

Jon

[Dumbstixlars]

Any updates?

[j.m.]

Nope!! He's buying lacrosse gear instead of batteries. :thumbdown::thumbdown: