losi madness
31-08-2010, 09:24 AM
my tekin rx8 sytem 2250kv
. its like new the truggy and shell comes with loads of spares and the rx8 sytem comes with hotwires and 2 packs of 4s lipos 3000mha 35c . the sytem as been set up and that it . . these pics are old pics before i put the rx8 sytem in it
LOSI 8IGHT - T BRUSHLESS CONVERSION
Bought this second hand about 9 months ago as a project. It looked to be in good condition but on delivery it was sadly a little tired. Since then I've sent a fortune refurbshing it and could have bought a new one for what it cost me. To name a few things:
New Hinge Pins
New Hing Pin Braces
New Hinge Pin Brace Covers
New Suspension Arms Front and Rear
Fully rebuilt Dampers
New Wing
New Protoform Body (This wasn't professionally sprayed so on close inspection there are a few flaws but from a distance or bashing it looks fine
New Bearings all round
New Diff Oil (7-10-5 Front-Centre-Rear)
New Hubs / Carriers front and rear.
New Servo Saver / Steering Linkage
1 New Diff Cup (Think the front one)
Also Included:
Losi Brushless Conversion kit fitted - Original Plastic ESC mount cut off so I could bolt the Beast ESC to the Chassis.
Carbon Suspension Mounts (Fitted)
Several Sets of Suspension Springs
Original Alloy Suspension Mounts
Damper Rebuild Kit
Comes fitted with Towerpro MG995 Steering Servo.
Comes with Acoms Reciever (NO XTAL OR TRANSMITTER)
Masses of Spares - Mainly the bits I've replaced but for a quick fix if you break something there should be enough to get you running again.
When I bought it I was told there are enough bits to convert it back to nitro if you want. I cant verify this but there are a load of nitro parts (Fuel tank / disc brakes / throttle linkage / engine mounts / Spur gear etc).
Original (tired) Body
Instructions + Box
Original Losi Wrench (not shown in the piccy's
.http://i832.photobucket.com/albums/zz247/simonb1978/02072010811.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/15062010751-1.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/24062010793-1.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/24062010791.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/15062010749.jpg
there loads and loads of spares with it 2packs of 7.4v 25c x2 and 2 packs of 4s packs 3000mha 35c
http://i448.photobucket.com/albums/qq202/at106/PICT0002-24.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0003-20.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0004-19.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0005-16.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0007-13.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0008-12.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0010-5.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0011-8.jpg
http://www.oople.com/forums/images/misc/progress.gif
. its like new the truggy and shell comes with loads of spares and the rx8 sytem comes with hotwires and 2 packs of 4s lipos 3000mha 35c . the sytem as been set up and that it . . these pics are old pics before i put the rx8 sytem in it
LOSI 8IGHT - T BRUSHLESS CONVERSION
Bought this second hand about 9 months ago as a project. It looked to be in good condition but on delivery it was sadly a little tired. Since then I've sent a fortune refurbshing it and could have bought a new one for what it cost me. To name a few things:
New Hinge Pins
New Hing Pin Braces
New Hinge Pin Brace Covers
New Suspension Arms Front and Rear
Fully rebuilt Dampers
New Wing
New Protoform Body (This wasn't professionally sprayed so on close inspection there are a few flaws but from a distance or bashing it looks fine
New Bearings all round
New Diff Oil (7-10-5 Front-Centre-Rear)
New Hubs / Carriers front and rear.
New Servo Saver / Steering Linkage
1 New Diff Cup (Think the front one)
Also Included:
Losi Brushless Conversion kit fitted - Original Plastic ESC mount cut off so I could bolt the Beast ESC to the Chassis.
Carbon Suspension Mounts (Fitted)
Several Sets of Suspension Springs
Original Alloy Suspension Mounts
Damper Rebuild Kit
Comes fitted with Towerpro MG995 Steering Servo.
Comes with Acoms Reciever (NO XTAL OR TRANSMITTER)
Masses of Spares - Mainly the bits I've replaced but for a quick fix if you break something there should be enough to get you running again.
When I bought it I was told there are enough bits to convert it back to nitro if you want. I cant verify this but there are a load of nitro parts (Fuel tank / disc brakes / throttle linkage / engine mounts / Spur gear etc).
Original (tired) Body
Instructions + Box
Original Losi Wrench (not shown in the piccy's
.http://i832.photobucket.com/albums/zz247/simonb1978/02072010811.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/15062010751-1.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/24062010793-1.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/24062010791.jpg
http://i832.photobucket.com/albums/zz247/simonb1978/15062010749.jpg
there loads and loads of spares with it 2packs of 7.4v 25c x2 and 2 packs of 4s packs 3000mha 35c
http://i448.photobucket.com/albums/qq202/at106/PICT0002-24.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0003-20.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0004-19.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0005-16.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0007-13.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0008-12.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0010-5.jpg
http://i448.photobucket.com/albums/qq202/at106/PICT0011-8.jpg
http://www.oople.com/forums/images/misc/progress.gif