Caster S10b

[TheReferee]

Joe will be driving the caster 4WD next season, so i thought a few build pictures. not sure how this works so might be a few teething issues on the pictures:cry:
19031

exciting box shot!!

[TheReferee]

well that worked, so i will continue later

[TheReferee]

Why the caster?
having competed for the last two seasons with the BMAX, it was getting a bit tired and we had a choice of buying a new BMAX or looking at something else.

at the Kidderminster MAMS meeting we saw the caster and thought it looked promising, a chat with the guy racing it(sorry didn't get your name) and a good fondle of his car gave us something to think about on the way home.

did some research on the internet talked to Answer rc the distributers of caster in the Uk, did a bit more research and placed an order.

It is available in 3 versions. a brushed RTR, a brushless RTR and the alloy pro kit. general consensus was the RTR was all plastic and too flexible whilst the pro was all alloy and too stiff!. however all parts are interchangeable and the way to go was an alloy kit with a plastic chassis.

there are some RTR features of the pro kit. dogbone rear driveshaft and centre drive shafts, however an upgrade kit to change these to the more usual CVD's was available.
there was also some issues with the slipper and diff bolts.

the pro kit comes with pre assembled diffs, but in our kit we received the upgraded gears,thrust balls and rear CVD driveshafts.

what we decided to do was build the kit box standard and then document the changes to the car to go racing.
so on with the build.

all the parts bagged and ready for assembly.
1903519036

start with the chassis and attach front bulkhead,motor mount and rear brace.190371903819039

All the crews are good quality hex head and all were attached using loctite.

diff cases are the same front and rear just add spacers for the rear one.
190401904119042

the diffs were put inplace and shimmed as required, we have not received the CVD centre shafts yet so we are building with the dogbone setup, no grease in the gearbox yet as we will be rebuilding them with the upgraded gears and ceramic ball later.

attach shock tower to gearcase and bolt down with the ball stud carriers

19043

shiney!!

[TheReferee]

on to the steering.
a bag of bits.
19045

steering parts laid out
19046

and attached

19047

at this point i was going to attach the top decks.
19048

however mr machinist obviously went to lunch and left this bit.
19049

not a big deal 5 minutes with the dremel and sorted, well actually as the dremel was flat it had to wait a bit.

so onto the steering hubs etc all alloy and very nice fits.
19050
19051

attached to wishbones and front brace fitted.
19052

rear hubs same quality
19053

at this point the dremel was up and running so top deck adjusted and fitted.
19054

almost a roller

[Holeshot]

Nice pics/build. This buggy is under-rated. Really nice looking chassis.

[Rodrego]

I have a Caster S10b too. It's a good sold (infact bullett proof) car, but is a cheaper version of the Hot Bodies Cyclone D4. If you go on-line and look at the old Hot Bodies site you'll see quite a few similarities between this car and the D4 Cyclone.

I'm not knocking it, just pointing out that it's not a completely new car. Just HPI re-realising it under a different brand/diguise :blush:

I was looking at running mine up north, but have decided to concentrate on 2wd. Think I'll be putting mine up for sale shortly.

PS: Have you rebuilt your diffs yet? I understand that the D4 locking nut assembly is a must!

[johnnygibbon]

car looks awsome i when i first saw it i was tempted and i was hoping it would have geared diffs but when i found out they were ball -decided to stick with my bmax ( well upgrade it to ft ) and i am very glad i did
my mate at racing got one of the mint ones and one of the cheap ones for spares as well came to race at bury and chadderton and did not complete a race - or start one in some cases . generally because the diffs are crap and need bits replacing or other cars diffs fitting . think he had a few issues with some other bits possibly steering and hubs
any way after a very annoying day his car broke on the way to the start line for the final and proceeded to be kicked back to the pits in a explosion of parts and anger
i have met a couple of people who like em though but only after heavilly modding the diffs with b44/d4 bits
personally i think it has some nice features but might need work to keep racing
i think you might be pushed to keep it going as long and reliably as your bmax but keep us updated with its ongoing performance
also it will not fit durango diffs in it like the lazer/bmax/d4

[fastinfastout]

car looks awsome i when i first saw it i was tempted and i was hoping it would have geared diffs but when i found out they were ball -decided to stick with my bmax ( well upgrade it to ft ) and i am very glad i did
my mate at racing got one of the mint ones and one of the cheap ones for spares as well came to race at bury and chadderton and did not complete a race - or start one in some cases . generally because the diffs are crap and need bits replacing or other cars diffs fitting . think he had a few issues with some other bits possibly steering and hubs
any way after a very annoying day his car broke on the way to the start line for the final and proceeded to be kicked back to the pits in a explosion of parts and anger
i have met a couple of people who like em though but only after heavilly modding the diffs with b44/d4 bits
personally i think it has some nice features but might need work to keep racing
i think you might be pushed to keep it going as long and reliably as your bmax but keep us updated with its ongoing performance
also it will not fit durango diffs in it like the lazer/bmax/d4

you can fit durango diffs in the bmax?

is it easy?

[johnnygibbon]

they drop straight in the bmax casing and i think the drive shaft and coupling fits one side of the slipper but not the other
however it will need new bearings and some shims which i havent bothered to measure up and order yet
it should be a very simaler install to how nick c did his lazer ( i think its on here somewhere) and there is some where on here that some one has modded some into a d4
i managed to get some 2nd hand durango diffs and drive shafts and worm gears and have started working out how to get it in the bmax in my old champ pack car
but recently it has been ripped to shreds by my fellow bmax owners who cant drive or be bothered to order spares .......
so progress is slow however initially its looking good the rear diff and drive shaft would be easyer to fit but i think a bit of modding and maybe some kyosho coupling parts might be needed to do front
as i get more time and bits i will start a thread with pics hoping to get it running by summer when were outdoor again and the diffs take a heavy beating

and i still think its a pity that not many 1/10th cars run geared oil diffs they are strong dont wear and once set up almost maitainance free
in my 1/8th they are perfect and in my 4wd sc truck they take a beating every week
why is there not more in 1/10th - especially in cars like this castor
sorry to go off topic move this to the yokomo forum if ya want guys

[TheReferee]

As i said in an earlier post i had done my research and am aware of the issue with the diffs.

the diff nut is 2mm and is locked in place by another 2mm nut, it is almost impossible to adjust and set the diffs correctly, several people have modified the diffs using as has been suggested D4/b44 parts.
the remaining issues have been the quality of the gears and drive rings, actually there is nothing wrong with the quality of the gears the issue is in the shimming of them. just like the BMAX if you dont shim both the main and bevel gears correctly they will be stripped by the second lap.

however the kits from Answer RC are now shipped with a nice pack of shims for this purpose and having spent this afternoon pottering in the workshop have come up with several solutions to the diff problems, simple cheap and painless.

so first thing strip the kit diff, at which point you will understand how difficult it is to get hold of that 2mm nut!!.

then go on the internet/phone DMS and order associated AS31167 which are TC5 outdrives.

you end up with these
19072

find the 2mm nut and push it into the T nut carrier and for a £4.99 plus P+P your done.
19073

as with all the cars i have rebuilt the diff using ceramic diff balls, my personal choice is the vampire ones again from DMS or your local X factory stockist.

onto the diff rings, stock kit ones are notchy and not smooth. according to our american friends "BFAST" are the dogs, however i have not used them so cant confirm, i can however confirm that losi XXX-cr shims are a straight fit and i had a pair so in they went.

i used the stock kit gear however for those who wish too BMAX gears drop in. not sure on the bevel gear as that is the next job.

one thing i did notice is the bevel gear runs eccentric, on initial inspection of the RTR diff and the PRO diff both bevels ran with the same eccentricity, i assumed a poor moulding, however it is just not fully seated, a quick tap on a hard surface and it runs true, just to confirm i did it to both diffs and it cured the problem.

put the diffs in the car paying particular attention to the bevel gear shimming and all was smooth.

because i can and i have the necessary parts i am going to run one car with the kit gears and the other car with alternate gears (BMAX) to see if indeed its quality or just proper building thats the issue.

[TheReferee]

having just reread my post you should note you get two T nut carriers in a pack, i pictured only one as i had already fitted one

[turbobrick]

As John says a large amount of the gearbox troubles I've heard about are due to either not being shimmed correctly or the slipper being too tight.

All I've changed in mine are the balls and diff plates, it's now ran for about 5 meetings without a problem. (now I've said that it'll die at the next meeting:) )

Peter

[JCJC]

Thats nice work John, we still have our D4 and would be interested to know how easy it is to swap parts, you know how difficult D4 parts are to find. The diff shimming reminds me of the Kyosho XZ5 if not fitted right & tight it stripped the gears. All the best with it, Mick

[jimmy]

Thanks for posting this John - car looks really nice, hope they get the diffs sorted

[budgio]

Could this be the same car with stick pack layout and B-max shell?
http://www.hobbytech-rc.com/car.php?id=160
It looks very similar

[audriusv]

Thanks for posting this John - car looks really nice, hope they get the diffs sorted

Diff are sorted out. On loose outdoor tracks we do not have problem with properly shimmed original diffs. For those who is running on carpet or mod motors there is Metal Bevel Gear 16T&Metal Diff Gear 39T

http://casterracing.com/news/main_view.php?cid=7&iid=59&id=898&urno1=1

And newest Pro Kit will come

1. with Front & rear CVD (SKOP034);
2. with Pressure Diff Sets (SKOP035) Front & Rear;
3. Ceramic Balls (SKOP036) x 26 pcs;
4. with White Teflon pistons (SKOP030) x 4 pcs.

I think price will be a little bit bigger, but not to much...

[audriusv]

Could this be the same car with stick pack layout and B-max shell?
http://www.hobbytech-rc.com/car.php?id=160
It looks very similar
Caster Racing are producing some things for hobbytech so it could be very similar...

BTW maybe someone could direct me where online I can buy this Hobbytech buggy?

[chokoboy]

Im about to trade my good ol' B44 with a NIB SK-10 pro, is this a dumb move?
I was thinkin about gettin' a plastic chassi, some front/rear cvd's, thrust bearings, bfast diffrings and some metal gears.
Some say the slipper and bevel gears work ok if they are shimmed right.
Others say go for D4/B44 gears, what's the clue here?

Thanks in advance!

@John the ref lookin' forward for a update on ur building tips!

[audriusv]

Im about to trade my good ol' B44 with a NIB SK-10 pro, is this a dumb move?
I was thinkin about gettin' a plastic chassi, some front/rear cvd's, thrust bearings, bfast diffrings and some metal gears.
Some say the slipper and bevel gears work ok if they are shimmed right.
Others say go for D4/B44 gears, what's the clue here?
...

Hi,

I traded my B44 for Caster :). In here we run only on big 1/8 outdoor tracks so B44 is not so reliable in these situations. First I got plastic RTR, now I have also Pro version (just not build yet).

Bevel gears are ok if you shim them right. They are ok if you do not ride with mod motor on high grip tracks. If you do - change to Kyosho/AE/HB gears or Caster new metal gears

http://casterracing.com/news/main_view.php?cid=7&iid=59&id=898&urno1=1

[Dreadstar]

Here's a vid from the Green Hill track in Sweden,running the SK10 Brushless RTR,for those that haven't already seen it in action.

http://www.youtube.com/watch?v=gOzZFiUsHNI

[chokoboy]

Hi,

I traded my B44 for Caster :). In here we run only on big 1/8 outdoor tracks so B44 is not so reliable in these situations. First I got plastic RTR, now I have also Pro version (just not build yet).

Bevel gears are ok if you shim them right. They are ok if you do not ride with mod motor on high grip tracks. If you do - change to Kyosho/AE/HB gears or Caster new metal gears

http://casterracing.com/news/main_view.php?cid=7&iid=59&id=898&urno1=1

Thanks audriusv,
Are the Kyosho/AE/HB gears a direct fit or does it need some mods other then proper shimming?
Do people use the caster slipper or do they use something else?
Going to run mod motor so maybe best way is to get the metal gears!
My other buggys use losi/AE/Tamiya rear rims, any mods i can do to use the same rims? Hassle to buy tons of rims&tires ust for this car!

[TheReferee]

Im about to trade my good ol' B44 with a NIB SK-10 pro, is this a dumb move?
I was thinkin about gettin' a plastic chassi, some front/rear cvd's, thrust bearings, bfast diffrings and some metal gears.
Some say the slipper and bevel gears work ok if they are shimmed right.
Others say go for D4/B44 gears, what's the clue here?

Thanks in advance!

@John the ref lookin' forward for a update on ur building tips!

i am moving house this week so might be a delay, have had one race meeting running standard diffs, 3 rounds and a final with no issues motor was a 6.5 novak in greasy conditions
john

[audriusv]

Thanks audriusv,
Are the Kyosho/AE/HB gears a direct fit or does it need some mods other then proper shimming?
Do people use the caster slipper or do they use something else?
Going to run mod motor so maybe best way is to get the metal gears!
My other buggys use losi/AE/Tamiya rear rims, any mods i can do to use the same rims? Hassle to buy tons of rims&tires ust for this car!
Kyosho are direct fit. USA colleagues say that HB seems to fit nicely in front diff but in rear it needs some work. Do not remember about AE...
Caster slipper is not bad but... to adjust it you have to take it out from buggy so some drivers went to HB D4 slipper... But it is expensive and not easy to find...:)
Even with mod motors if you shim correctly and set correctly slipper you should be ok with standard gears... But always it is good to have spare ones :)
A quote from casterracingusa forum: "Tamiya and any other with a zero offsett and 12mm hex, pin style wheels with a shim behind the pin will work...". I do know for sure that wheels with 12mm hex and zero offset fits nicely :). Sold all B44 wheels so can not say anything about pin style rims...

[Holeshot]

Caster Racing USA would like to announce that we are upgrading our S10B Sniper Pro 1/10 scale 4wd cars. The Sniper is very unique in that 90% of parts are available in plastic or aluminum and 10% are also available in US made carbon fiber as a third choice based on cost, performance, and/or durability.

Our cars are dialed and very solid out of the box, but we decided that the drivetrain needs to be there also if we want to be competitive in the marketplace.

The pro cars will now come with stainless steel washers, ceramic ball diffs, additional washers to ensure the delrin gears are solid, and the new pressure differential set. Just to prove that we are serious, we also just finished producing center and rear cvds and metal bevel gears just to shore up any possible durability issues. New price to be determined, but parts and kits have probably landed in the United States by the time you are reading this.

http://i52.tinypic.com/se2dxy.jpg

http://i55.tinypic.com/iqlgcg.jpg

http://i52.tinypic.com/k3vome.jpg

http://i54.tinypic.com/1w9bd.jpg

http://i52.tinypic.com/30afj1u.jpg

http://i56.tinypic.com/2wp5fgg.jpg

[Holeshot]

Anyone got any more feedback on its performance. Im considering purchasing the s10b and the sk10 rtr for my son.

[Nick]

Video of SK10 at the petit

http://vimeo.com/19005086

[Thomas P]

I have done app 15-20 packs with my S10B rtr..changed electronics to Speedpassion LPF/6.5r v3 motor..the car out of the box is real good..i think everyone that change motor to a faster/stronger need to shim the diffs..i had not all the time, so i changed the maingear in the diff to B44..and then shimmed..i have a friend that runs it box, but with other oil, lipo and stock BL, no problem at all..

for the last 4-5 years i have been running BJ4WE/Atomic Carbon S4 and B44..and this is the car i like best, this is my opinion..i have been doing some testing now, and it works better and better..the car is smooth, and EASY to drive, with lots of gripp and quick..we are running Schumacher slicks (mini pins), tiresauce..cant wait to next run..

http://i123.photobucket.com/albums/o306/gabbax_74/Caster%20S10B/S5030604.jpg

[RCAshers]

Hi Thomas I have just fitted the top Ali stiffener plates and Ali motor mount on my basic roller, I have also fitted the new metal diff gears and bevel gears, it has made the buggy much stiffer and with a 5.5 motor setup in it it flies. I done think you would need to go to the pro version unless you want the bling.
Regards Ashley

[Thomas P]

Hi Ashley, sounds good, what about the metal ones..do they sound a lot ?..if not, they may be an option to run.

[Thomas P]

New lid..


http://i123.photobucket.com/albums/o306/gabbax_74/Caster%20S10B/S5030610.jpg
http://i123.photobucket.com/albums/o306/gabbax_74/Caster%20S10B/S5030609.jpg
http://i123.photobucket.com/albums/o306/gabbax_74/Caster%20S10B/S5030608.jpg

[RCAshers]

http://i655.photobucket.com/albums/uu271/RCAshers/CasterSB10Buggy004.jpg

[RCAshers]

I'm getting old I forgot to add the text, Pic shows buggy with Ali top braces fitted. I also fitted the Ali motor mount as it holds the meshing better and displaces heat better, the metal diff gears run quiet and smooth. I like the new body what is it from I want one. I can supply you caster parts if you ever need them. Regards Ashley

[Thomas P]

So the DD chassi arrived for a few days..could not hold, so i mounted her up...this is the result, sad i cant try it untill next weekend..

http://i123.photobucket.com/albums/o306/gabbax_74/ae676bb2.jpg
http://i123.photobucket.com/albums/o306/gabbax_74/2e43754b.jpg
http://i123.photobucket.com/albums/o306/gabbax_74/9757e356.jpg

[pjhibb]

hi was wondering i just bought my first radio controlled car castor s10b the front cvd drive shaft has broken away from the drive cup so the wheels not turning looks like its a pin thats missing have u got a picture of a the part or name of the part i need to fix it with i have circled the parts in my instruction book that i think i need. Any help would be great thanks peter.

[audriusv]

I do not know is there CVD Joint + Set Screw for front CVDs... Pin part number is "SK101" (for all CVD's). And there is full set of front CVD "SK102-A Front CVD Set". You have to look exactly for "SK102-A", not "SK102" (it is only shaft). I will ask Caster Racing for CVD Joint + Set Screw part number and post back.

[ADW]

hi was wondering i just bought my first radio controlled car castor s10b the front cvd drive shaft has broken away from the drive cup so the wheels not turning looks like its a pin thats missing have u got a picture of a the part or name of the part i need to fix it with i have circled the parts in my instruction book that i think i need. Any help would be great thanks peter.

Did you get part number for part? Who did you order it from?
I'm looking for one also.
Rgs,
A

[audriusv]

Part number is SK132 CVD Joint+Set Screw (2pc).

[markymark6183]

what set ups do you guys use i.e what holes in the shock towers for loose surfaces ???

[whizzy]

what set up do you run on astro any other problems you are finding with them

[ADW]

what set ups do you guys use i.e what holes in the shock towers for loose surfaces ???

Hi,
I drilled out 2 extra 1.5mm holes in front and rear pistons. (Black 2 hole, now 4 hole) 25wt in rear and 30 in front. Losi lime green springs rear and blue on front. Polished shafts. This seem to help the handling over bumpy track.
A few practice laps with the Caster S10B
http://www.youtube.com/watch?v=k8Ku3IZfvIM

[markymark6183]

Who's using what diffs in there caster as I'm having a right game with mine, I've shimed them but they still don't mesh right, ( this is with standard caster diffs)
Anyone got any ideas
Cheers

[JonyNitro]

Who's using what diffs in there caster as I'm having a right game with mine, I've shimed them but they still don't mesh right, ( this is with standard caster diffs)
Anyone got any ideas
Cheers

I used B44 when had mine, sell it:thumbsup:

[ADW]

I changed to HB gears (D4) and still running first set. I'm running Bfast diffs and Ive changed to HB slipper plate, pads and spur. HB are direct fit, modifications required if you go with team Associated B44 gears (metric v's Imperial).
Hope this helps.
Rgs A


Who's using what diffs in there caster as I'm having a right game with mine, I've shimed them but they still don't mesh right, ( this is with standard caster diffs)
Anyone got any ideas
Cheers

[markymark6183]

I changed to HB gears (D4) and still running first set. I'm running Bfast diffs and Ive changed to HB slipper plate, pads and spur. HB are direct fit, modifications required if you go with team Associated B44 gears (metric v's Imperial).
Hope this helps.
Rgs A

Nice one fella, I love the car it's just a case of sorting out the teething problems :thumbsup:

[audriusv]

Who's using what diffs in there caster as I'm having a right game with mine, I've shimed them but they still don't mesh right, ( this is with standard caster diffs)
Anyone got any ideas
Cheers

Hi,

cheap Kyosho ZX5 gears fits nicely in Caster.

But. Caster already have new stronger gear boxes in which will fit new GEAR DIFFS. Yes, correct, gear diffs not ball diffs. So I would suggest just wait few weeks for gear diffs and then give Caster buggy another chance :).

[markymark6183]

Hi,

cheap Kyosho ZX5 gears fits nicely in Caster.

But. Caster already have new stronger gear boxes in which will fit new GEAR DIFFS. Yes, correct, gear diffs not ball diffs. So I would suggest just wait few weeks for gear diffs and then give Caster buggy another chance :).

Can you let us know when there out please ??:D

[audriusv]

Gear Boxes are already out. I am told three-four weeks for gear diffs...

[pinussen]

Where can you buy the gear boxes?

Gear diffs might be a good backup, just found that I had crushed/ground down the pressure plate balls in one of my diffs :( Have to wait for delivery from Bfast for some real balls...

//Björn

[audriusv]

They should start to appear in online shops.

Caster is about to launch (in two-three months) 1/10 truggy and SCT... They will come with gear diffs as standard.

[markymark6183]

Anyone got any good tips on how to get the car to initially turn in a little sharper ?

[pinussen]

Hi,

I think I have finally got a good setup of the ball diffs. This is how I have them now:

Normal outrunners, Bfast copper shim, Bfast ring, Caster Ceramic balls, Steel gear. The screw has been changed to a screw and t-nut from Ass (for the B4, M2.5 instead of M2) and the pressure plate has ceramic balls from Bfast. Grease from Bfast. Nut goes in the longer outrunner together with the sping and it's shims, you might need a few more shims so the nut ends up far enough out.

Really smooth diff, and it almost feels like the nut is broken when you turn the wheels opposit each other, you can have it so loose without slipping.

Note that I had to enlarge the hole in the outrunners slightly to accept the M2.5 screw. I also had to enlarge two of the shims for the same reason, can't remember if it was for the preassure plate or spring. Bfast shims for the preasure plate worked fine though without enlarging. To enlarge the hole you need a diamond tool or something like that since the outrunners are hardened, I found a narrow tipped tool from an engraving set I had.

Normal run in of the diffs and now I have put two packs through them without the need to tighten them. :thumbsup:

Really fun to drive around on my grass/dirt track with slicks now (normal tires worn down).

[Sumilidon]

Just in case I am missing something, how the hell do you fit the RTR parts into the Pro kit?

The ESC if put on the side is too high for the lid, if it does get pushed down, it completely blocks the fan.

I'm ultimately sticking the electrics in the touring car but would at least like to try the pro car as my ESC in the post is the same size.

Any pictures of how you guys have set up the electronics?

[audriusv]

Finally Gear Diffs are available for this buggy! Also new gear boxes with better shock tower supports and new better shock towers! Also shortly will be available shock tower support brace.

SK0P051 Diff Set +16T Diff Pinion Gear (1pc)

SKOP057 Gear Case For Gear Diff Set

SKOP055 Rear Shock Tower 7075

SKOP056 Front Shock Tower 7075

SKOP059 Shock Tower Support

Also there is conversion set with better price

SKOP058 1/10 Gear Diff Conversion Set

2pcs make 1 car set.

[markymark6183]

he's one for you !!!!!!! my caster has been running great the last 5-6 weeks then today my rear bevel gear melts !!!:confused: ive put a kyosho zx5 one on as its alot better quality, i just wonder if you guys know what melts a bevel gear ?????

cheers chaps

[Chrissy Boy]

Just curious to know if anyone is still running one of these, saw a "B" version up for grabs on e-bay, cab forward body, wondered if the teething problems where now sorted. It is a nice looking car and is certainly a little different so could be tempted. :)

[Collegeboy]

Still running mine, but with lots of mods. The car is almost a version 3 minus big bores and the new CVD's. Love the car and it is very competitive. This is the second year competing in the regional series. Have also made a 2wd version that I ran at the first round of the oople series (Jimmy has loads of pics) and running in tis years 2wd regionals.

I love having a car that is different,and from my engineering background, I enjoy making it even better.

[Chrissy Boy]

Excellent, so spares are not a problem then, and the diff probs have been ironed out? As I said, very tempted by one of these. Out of curiosity what surface do you race on, my local club runs on grass and it has all the usual suspects as 4wd competition, Durango, Schumacher, Associated etc, if I get one and get it dialled in is there any reason to think I shouldn't be able to cling on to the coat tails of those guys?

[Collegeboy]

Hi Chrissy boy,

The diff issue has been sorted, if you want to use a ball diff, then caster do a metal crown and pinion set (some people say these are not available now). Alternatively I run the gear diffs in my 4wd, with a starting point 7000wt front and 3000wt rear for astro. For carpet/slippy (Maritime race way) 3000wt front 2000wt rear. In my 2wd version (Raster), I have been running gear diff with 5000wt. I'm going to try a ball diff for this weekend at my local track (Surrey/Hants) and maybe at next weeks 2wd regional at DMS. Pete and Carl at Answer Rc can help with spares as they are the sole importers and are extremley helpful and friendly. As for being a competitive car against other brands out there, it can and does hold its own. I quite often have good battles with fellow racer who at the start say 'you still running that thing'. Then I finish higher than them:woot:, but I never rub their noses in it;):woot:. If you decide to choose this car, PM me your email address and I'll gladly send you setup sheets and offer any help I can.


Paul

[Holeshot]

Hi Chrissy boy,

The diff issue has been sorted, if you want to use a ball diff, then caster do a metal crown and pinion set (some people say these are not available now). Alternatively I run the gear diffs in my 4wd, with a starting point 7000wt front and 3000wt rear for astro. For carpet/slippy (Maritime race way) 3000wt front 2000wt rear. In my 2wd version (Raster), I have been running gear diff with 5000wt. I'm going to try a ball diff for this weekend at my local track (Surrey/Hants) and maybe at next weeks 2wd regional at DMS. Pete and Carl at Answer Rc can help with spares as they are the sole importers and are extremley helpful and friendly. As for being a competitive car against other brands out there, it can and does hold its own. I quite often have good battles with fellow racer who at the start say 'you still running that thing'. Then I finish higher than them:woot:, but I never rub their noses in it;):woot:. If you decide to choose this car, PM me your email address and I'll gladly send you setup sheets and offer any help I can.


Paul

Have you got parts number for the metal crown/pinion set for the ball diff? My son has the RTR version (ball diffs) and ran into a car tyre pretty fast. He broke the front upper and lower gear box and the front gear mount. Went to order the SK055 gear box case but couldn't see it listed on http://www.casterracingparts.com/ (http://www.casterracingparts.com/) or anywhere else. SKOP057 is the case listed for the gear diff and pretty much looks identical so ordered it to try out. Everything fits it but the mesh between the bevel gear and diff gear is to tight.

[Holeshot]

I used B44 when had mine, sell it:thumbsup:

I changed to HB gears (D4) and still running first set. I'm running Bfast diffs and Ive changed to HB slipper plate, pads and spur. HB are direct fit, modifications required if you go with team Associated B44 gears (metric v's Imperial).
Hope this helps.
Rgs A

Hi,

cheap Kyosho ZX5 gears fits nicely in Caster.


Are you only replacing the whole diff or just the ring gears?

[Holeshot]

Amain Hobbies look to be getting out of Caster Racing and have all their parts at crazy clearance prices so if anyone here is running a SB10 check out Amain. Note - their prices are MAP pricing, add it to cart to see actual price or log in.
http://www.amain.com/Search?cID=5321&fb=864&lg=fb

[imull]

Just landed one of these for my son to learn on but it's not got a shell. Apart from the kit one (which I've not found at the moment, although I've not looked that hard) what are my shell options? Do the B44 ones fit, as the layouts look similar?

Also what fitting are the wheels? 14mm hex?

TIA

Ian

[Holeshot]

I've heard of people running the b44 body but can't remember if any additional mods were required. I'll have to try and find the info. And just standard wheels. It runs the same wheels as I run on my losi 22-4.