Yokomo 94 YZ10
 

Yoke 94 looks in pretty good condition a little dusty and and could do with a clean. Chassis hasn't really got any scratches on but has got a few sticky pads that need removing.
Found some front shocks and a layshaft to go with the car
I'm looking for SOLD plus post and PayPal fees please.

https://www.ebay.co.uk/itm/222342946276

http://i1345.photobucket.com/albums/...psfinpafm7.jpg
http://i1345.photobucket.com/albums/...pso4t0geay.jpg
http://i1345.photobucket.com/albums/...psvgjddw6q.jpg
http://i1345.photobucket.com/albums/...pszxhzqewd.jpg
http://i1345.photobucket.com/albums/...ps7j7rsjvs.jpg
http://i1345.photobucket.com/albums/...pscdygr4mq.jpg
http://i1345.photobucket.com/albums/...psstgpfboa.jpg
http://i1345.photobucket.com/albums/...psdqpomnya.jpg
http://i1345.photobucket.com/albums/...psybyft0p3.jpg

:thumbsup:

Not takers on eBay then, been a few yz10's not selling recently

There was a guy on here massaged me and then never got back to me but there's a guy on eBay from Aus wanting it but he doesn't want to pay 😂😂

:thumbdown: bloody ebayers always want someting for nothing had stuff on there for a couple of quid and people still want it for less basically meaning it would cost me money to send it them :confused:

dude that is SO wrong:woot::woot:

Hilarious! See Justin your crap spelling can get you into all sorts of assumed trouble :)

:lol::lol::lol::lol::lol::lol::lol:

Id run in the opposite direction, unless it was a nice lady then couldnt refuse 😉😉😉😉

Justin, sorry for asking again, what bits do I need to make a proper slipper clutch on this car but with a one way?

You can either hunt for a TCS Kit which is part number ZC-670c or for the individual parts


ZC-670 TCS (Torque control system)
ZC-671 TCS hub set
ZC-672 Center shaft for TCS
ZC-673 TCS Teflon Cluchdisk (AS.6585 also compatible)
ZC-674 Front drive pulley (for Ctr shaft)
ZC-675C TCS Thrust bearing
ZC-676C Inner bearing for TCS
ZC-677C TCS Maintennace kit

If the part number has a H after it that means it's the hardened part

Hi Justin, do you know the part number from that layshaft kit on your last picture?
I've seen an layshaft with thread on it, but never the hole kit with front drive pulley, that looks interresting....
It looks like, you can adjust the amount of slipping from the front drive line, like the FAB system from Schmacher!?

Ps.: i'm looking for an T.C.S kit for quit a long time allready, these thing is realy hard to find, have some single parts from it, but still missing the hub set...:(

Layshaft!
 

I found the answer of my question by myselve, the parts number of the shaft and hardware is zc-644, i do found one of these in my spare box, but there is another question comming up, as these is, does that asambling need an separate/different front drive pulley, that is not included in the kit...

Sorry for off topic!

Hi Mate sorry I didn't get back to you, for the TCS you want the ZC-672 as stated erlier you can't use the 644 with the TCS it won't fit. There are some 672's on eBay for a reasonable price if you look on eBay.com

Now on eBay

https://www.ebay.co.uk/itm/222342946276

Ends in 10 min :woot:

Happy with the price?

I just wanted to ask the same!:lol:

For what it owes me yes, you win some you lose some and I've just picked up another 95 cheap :lol:

:lol: where do you find these things

You've just got to look for them buddy :D