TC02C-Evo T-Plate
1 Attachment(s)
Just starting to programme some of these.
|
Very nice:wub
|
Quote:
|
Quote:
But I tell you now, it isn't going to be orange!!! It's an uphill task selling aluminium bits to Team-C owners if it isn't ruddy orange. :) |
:mad: ORANGE :mad:
:thumbsup: |
Please bring them out I know team c Australia will grab some from u as I've been going on about this part of the car for a long time as its way too flexie :thumbsup:
|
1 Attachment(s)
Quote:
If I know, in advance, how many might be wanted it will help me to sort out the best batch size. |
1 Attachment(s)
The first-off of the TC02CEvo T-Plate is completed.
This one gives the standard anti-squat setting plus two steps lower. This wasn't the original intent but useful for anyone wanting a zero anti-squat setting. ;-) The next version will give one up and one down from the standard. (Hopefully) |
2 Attachment(s)
We fitted Clive's Aluminium T-Piece today. Beautifully made and a straight swap with the plastic T-Piece.
Attachment 78546 Attachment 78856 |
1 Attachment(s)
These T-Plates for the TC02C-Evo are now available from stock at £26 plus postage.
EDIT: They were in stock for about five minutes! Now out of stock and awaiting further material supply. :-( |
Quote:
Well that's good! Get some more stock in, I would like 1 please:thumbsup: |
Quote:
Best bet is to send me a pm with your email address so that I don't lose you in the forums. I'm sure that there was an Australian bloke said that some would be required over there but I'm blowed if I can find him again, either here, on RCTECH or on Team-C. :rolleyes: |
Ok will do, cheers mate. I might need to get a few for my friends here in Sweden.
|
Quote:
Up until I stated that they were available from stock I only had three firm orders, so I made a batch of ten. An hour later I had none left! So the batch should have been larger. I currently have one cnc machine and all of the things that I make go through it. If it's making T-Plates it cannot be making C-Drives and I have now run out of both and, to compound the situation, the machine needs some maintenance! |
Quote:
Well I will have 6 please. I'm sure they will sell easy! |
Quote:
|
Quote:
Didn't know you had that many friends! :woot: |
Quote:
|
1 Attachment(s)
The stiffness of the aluminium T-Plate has allowed me to try a different layout as shown on the attached. I'm still using my pre-Evo version of the T-Plate and gearbox, grafted to the Evo chassis so you may need a slimmer ESC to do the same with the Evo box.
The HBI T-Plate has been clocking up some good results in Europe, the latest being Oskar Levin's domination of the Swedish National: https://www.facebook.com/teamrchobby...type=1&theater Prior to that Nico Risser gave similar treatment to the oposition at Round 3 of the Belgian/Dutch Championship: https://www.facebook.com/69584277717...type=1&theater and William White came out on top at Round 1 of the Irish National Championship: https://www.facebook.com/photo.php?f...type=1&theater The T-Plate uses standard TM4 inserts to give one step up and one step down from the standard anti-squat and the use of Team-C's rear hanger provides similar adjustment about the standard roll-centre adjustment. A special has been commissioned by William White to move the front inserts 3mm further apart, enabling the maximum track width to be obtained with the gullwing wishbones. |
All times are GMT. The time now is 04:15 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com