Tp-Parts: "Timing" 2 belt driven 1/16 4wd Buggy
 

Season 11-12 project..all 1/10th parts based little 1/16 Buggy

Custom chassi
Custom towers
Custom topdeck
Custom front belt (order tomorrow)
CC CM26-6800 motor (3.17 axle)

FIrst spy shot of my chassi :p

http://i123.photobucket.com/albums/o...4/2358618e.jpg

Ali-parts

http://i123.photobucket.com/albums/o...4/8caced76.jpg

Rear

http://i123.photobucket.com/albums/o...4/5782895f.jpg

http://i123.photobucket.com/albums/o...4/a6e283d8.jpg

Side wiew

http://i123.photobucket.com/albums/o...4/bef8aa0b.jpg
http://i123.photobucket.com/albums/o...4/38adc786.jpg

Test mount

http://i123.photobucket.com/albums/o...4/cf7b7278.jpg
Enjoy

/T

Looks superb Thomas, great work! :thumbsup:

Mini 511! :thumbsup:

If it goes as well as it looks your on to a winner!

Thamks Mark, ihope so..for next version if this one works i have the 501x bulkheads here :)

That looks fantastic. Great work!

Thanks mate, :)

how much??? lol i want!!

To much :D

Nice!

I once cut and shortend an academy STR-4 tourer into a mini buggy. I ran it with a mini-inferno body on top.
Which body are you going for?

thats very nice :thumbsup:

Geardiff and new MM

http://i123.photobucket.com/albums/o...4/519facd3.jpg

Moter Mount? You're using a 380 or 360 sized moter, isn't it?
So which moter mount is in the bag, and on the car?

Yea, a Novak Three-80 or a Castle CM26

it is the stock mount on the car, the other is almost the same, but with a better spur/pulley holder.

about lid, not sure yet.

I'm a little confused: I'm not very much at home in Tamiya.
(It is using Tamiya touring car parts for the transmission , right?)

So how do you fit the 360 sized moter on a 540 sized moter mount???

Tp-Parts Timing 1/16 4wd belt driven Buggy vs Carisma Tp-Parts Chassi GT14B 1/16 4wd saft driven buggy

http://i123.photobucket.com/albums/o...4/d047cc64.jpg

(shocks are only mounted for pic, have to order a new set, this is Aduis shocks)

Geardiff installed, new motormount with quickchange gear

Some drilling and cuting

Ordered All Schumi parts,HPI and will get the Kyosho parts Monday i hope...if im lucky the belts will arrive mid this week, ordered some new bigger center pulleys to.

Have done som small mochup mount with the Xray M18T crank, lloks good..see wich one il use, i cross my fingers that the arms will fit in between the mounts..

Schumacher CAT SX arms fitted..Next, to get the HPI rear hub and Lazer front end..then it is measuring again,dremel,sanding the arms, to get the width good, next tricky par is to extend all CVDs...

http://i123.photobucket.com/albums/o...4/e4a62f48.jpg

Looking ace Thomas ,as per normal!
I like the look of your two1/16ths:)

Thank you Rebel, do my best =)

Belt arrived today , Jiiiippie :D

Just compared the Stock Tamiya arm, with my cut Schumi...

http://i123.photobucket.com/albums/o...4/94409346.jpg

No doubt, that il go for the Tamiya one, so much easier and less sandning,dremling

http://i123.photobucket.com/albums/o...4/4ac9629a.jpg

Would be awesome, i think it is to long, but that would be real cool :)

UPDATE

Ok, so there was no time today for any practice, so i took the chance to do some work on the Timing car :rawk:

And, i must say, i do believe more and more on this car, just waiting for the new front belt from Schumi UK

Using the Kyosho Lazer 4wd plastic inserts for the arm-axles reduced the sloppy a lot..

http://i123.photobucket.com/albums/o...4/cb86f1c7.jpg
http://i123.photobucket.com/albums/o...4/70f313a4.jpg

Left: Tp-Parts Timing 4wd Buggy - Right: Carisma GT14B 4wd Buggy

http://i123.photobucket.com/albums/o...4/78e39ee2.jpg

http://i123.photobucket.com/albums/o...4/cb6660bd.jpg

http://i123.photobucket.com/albums/o...4/f82b6130.jpg

Rear

http://i123.photobucket.com/albums/o...4/c4d58e5b.jpg

Front

http://i123.photobucket.com/albums/o...4/f271339d.jpg

Tomas är du säker på att den är "saft driven" :woot::thumbsup::thumbsup: ???

Btw who are you ordering youre belt from ???

mvh Isobarik