Go Back   oOple.com Forums > Search Forums

Showing results 1 to 25 of 39
Search took 0.00 seconds.
Search: Posts Made By: Ubiquitous
Forum: Vintage RC 16-02-2020
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
ZXR wheel offset and longer UJs

Hi all,


What is the wheel offset of the ZXR front wheels compared to that of modern, say Kyosho or Schumacher, wheels?


I have cracks in my ZXR wheels and recently broke a la-59 C-Hub in a...
Forum: Vintage RC 17-01-2020
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
I have mounted the VTS slipper with the AE 93T...

I have mounted the VTS slipper with the AE 93T spur and everything fits together. The problem is that I cannot use anything smaller than 24T for the pinion, which does not give the proper gear ratio....
Forum: Vintage RC 16-01-2020
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Trouble to mount VTS slipper

Welshy,


I got the B4 layshaft from Alcyon, the VTS slipper kit from AE, and the 100T spur gear from RW racing.

The center hole of the RW spur is 8 mm, the same diameter as that of the...
Forum: Vintage RC 12-12-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Thanks a lot Welshy! Now you have to...

Thanks a lot Welshy!



Now you have to post a picture of your car when the parts are mounted!


Ubi :thumbsup:
Forum: Vintage RC 12-12-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Welshy, Your belt tensioner is ready to order: ...

Welshy,
Your belt tensioner is ready to order:


https://www.shapeways.com/product/K6B2G4CQT/custom-belt-tensioner-3-mm-for-welshy40?optionId=137665643&li=shops



Please double check that...
Forum: Vintage RC 09-12-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Sure I can, no problem. I should be able to have...

Sure I can, no problem. I should be able to have it up on Shapeways by Thursday. I'll let you know anyway when it is ready.
Cheers
Ubi
Forum: Vintage RC 08-12-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Yes, I can move the lipo all the way up against...

Yes, I can move the lipo all the way up against the front mount and all the way up against the rear mount.

For the full front position, you need the belt tensioner to raise the belt so it does...
Forum: Vintage RC 03-12-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Belt tensioner

Thanks for the tip about the belt setup Welshy.


I am getting my 3D prints done on Shapeways at the moment. I am very pleased to see that you are interested in my belt tensioner design.
Below...
Forum: Vintage RC 23-11-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Thanks Iso! Do you have any advice for the...

Thanks Iso!

Do you have any advice for the belt tensioners, front and rear ?
Cheers!
Ubi
Forum: Vintage RC 21-11-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Setup for indoor

Hi All,
I am preparing my Lazer ZX-"T" for the indoor season here in Switzerland. I will be running on carpet for the first time. I am super excited!

Since the wheels of my truggy are bigger and...
Forum: Vintage RC 06-10-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Really nice work on vintage Kyosho cars! ...

Really nice work on vintage Kyosho cars!



https://www.neovintage-rc.com/projects/project-kyosho-lazer-zx
Forum: Vintage RC 06-09-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Yes Iso, what is white on my car is 3D printed. ...

Yes Iso, what is white on my car is 3D printed.


Cheers,


Ubi
Forum: Vintage RC 01-09-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
servo position

Hi All,


Just wanted to share this as it makes the steering adjustment a lot easier. All you need is a low profile servo and LA361 or the expensive 39655 equivalent.
With this I have a lot more...
Forum: Vintage RC 29-07-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
I replaced the stock ZX C-Hubs (0 caster angle)...

I replaced the stock ZX C-Hubs (0 caster angle) with these so it must only be appropriate for the shorter version.



I guess you are using the longer ujs...
Forum: Vintage RC 28-07-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
I will order one and test it. On a...

I will order one and test it.



On a different topic. I found out that the C-Hubs and steering knuckles from the Xray T4 are a direct fit for the Lazer ZX. They are available in medium, strong...
Forum: Vintage RC 24-07-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
la-31

Hi All,


I broke a rear tower mount yesterday. Tried to take a big double for the first time and ended up on the roof :thumbdown:.

The part was Alcyon's design 3D printed on Shapeways (the old...
Forum: Vintage RC 06-03-2019
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
3D printed parts

I have durability issues with some of the parts I got 3D printed by Shapeways in "versatile plastic". They have a new material called "professional plastic" that is supposed to be stronger and more...
Forum: Vintage RC 30-11-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Welshy, Do you use sway bars on indoor carpet? ...

Welshy,
Do you use sway bars on indoor carpet?
Thanks
Ubi
Forum: Vintage RC 28-11-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
sway bars

Does anyone know if there are sway bars from modern cars that can fit on the lazer zx(r)?
Thanks,
Ubi
Forum: Vintage RC 12-11-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Thanks Welshy for the reply, Where could I get...

Thanks Welshy for the reply,
Where could I get this custom B4 slipper layshaft?
Can I use a brushless motor without a rear belt tensioner? If yes, would 13.5T be good to start on a carpet track? I...
Forum: Vintage RC 10-11-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
I am confused, when you say 1.5 teeth for 0.5...

I am confused, when you say 1.5 teeth for 0.5 pinion tooth, do you mean that you use a 33 teeth pinion with you 100T spur?

This is highly geared compared to what I have with my brushed motor. Is...
Forum: Vintage RC 08-11-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Welshy, A spur gear with 93 teeth is only 7%...

Welshy,

A spur gear with 93 teeth is only 7% smaller than the stock one. Can this not simply be compensated by going down 1-2 teeth on the pinion, with the benefit of having a reduced rotating...
Forum: Vintage RC 22-09-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
One alternative could be the 3D printed design...

One alternative could be the 3D printed design from Alcyon. It is quite beefier than the la31 stock part and it is available on Shapeways:
...
Forum: Vintage RC 10-09-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Thanks guys, hopefully the 3D printed parts will...

Thanks guys, hopefully the 3D printed parts will not wear out too quickly...
Cheers,
Ubi
Forum: Vintage RC 07-09-2018
Replies: 5,975
Sticky: Lazer zxr
Views: 678,368
Posted By Ubiquitous
Lazer ZX Truggy

Hi All,

I've just tried my new Lazer truggy conversion and it runs great! It was a relatively long project (~6 months) but I am very pleased with the end result.

I built this car in order to...
Showing results 1 to 25 of 39

 
Forum Jump

All times are GMT. The time now is 02:27 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com