Go Back   oOple.com Forums > Search Forums

Showing results 1 to 20 of 20
Search took 0.00 seconds.
Search: Posts Made By: neallewis
Forum: Electrics 12-04-2014
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
http://www.teamtekin.com/hotwire.html 10.2...

http://www.teamtekin.com/hotwire.html

10.2 Includes the following features:

250 firmware platform specific to the RSX, RS GEN2, RS SPEC and RX8 GEN2.

Pending ROAR Approval

Added BEC...
Forum: Electrics 03-03-2014
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
my neutral width is set to 5 on my RS and RS Pro....

my neutral width is set to 5 on my RS and RS Pro. i think Dannys is 7 or 10 from memory. 52 will just remove lots of bottom end throttle control and create a bigger deadband around the stick centre...
Forum: Electrics 23-02-2014
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Smokes, i ran the same car on the same track...

Smokes, i ran the same car on the same track today. my slipper was really loose. i spoke to you about your car, its way too fast, over motored and boosting far too much for the grip level on the...
Forum: Electrics 26-11-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
My Gen2 faulty sensor board showed up fine on the...

My Gen2 faulty sensor board showed up fine on the sensor checker. Just broke down 4.5mins into a race and all went wrong, exactly as you describe. I'd say under heat, load and stress of running in a...
Forum: Electrics 25-11-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Kartstuffer, I had this problem on my 7.5...

Kartstuffer,

I had this problem on my 7.5 gen2 and RS Pro. I swapped in the sensor board from my Gen2 5.5 and it all went away. I'd say try a new sensor board on the motor.
Forum: Electrics 07-10-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
To me if it works fine on 2S, then I'd be looking...

To me if it works fine on 2S, then I'd be looking at your 1S booster wiring.
If you aren't using a booster, then you should be. My RS works on 1S without a booster (albeit with a slow servo), but my...
Forum: Electrics 12-09-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Sounds great, but when is it out to buy?

Sounds great, but when is it out to buy?
Forum: Electrics 20-08-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Have you stripped the motor down and inspected...

Have you stripped the motor down and inspected it? checked the bearings, rotor and ensured nothing is in contact with the rotor?
Forum: Electrics 15-08-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
No problem at all. You can use something like...

No problem at all. You can use something like this: http://www.rccarshop.co.uk/index.php/electrics/speed-controllers/hobbywing/hw86030030-hobbywing-power-capacitor.html

What difficulties are you...
Forum: Electrics 09-05-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
You'll need a booster to get it to work with 1S. ...

You'll need a booster to get it to work with 1S.

This: http://www.rcdynamics.co.uk/Booster.html
The Rolls Royce booster

or this:...
Forum: Electrics 04-04-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Not possible on iphone I know that much. apples...

Not possible on iphone I know that much. apples restrictions, not Tekins.
Forum: Electrics 04-04-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
I'm sure Randy will publish a link when the...

I'm sure Randy will publish a link when the software is released!
Forum: Electrics 20-03-2013
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
John, the RS is advertised as being for 2wd...

John, the RS is advertised as being for 2wd applications only. I think with all that current limit and load of the 4wd its too much. Have you tried it without the current limit? Also what capacitor...
Forum: Electrics 26-12-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Hotwire is Windows only, no ipad.

Hotwire is Windows only, no ipad.
Forum: Electrics 23-10-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
I do just this for my indoor track, but It's a...

I do just this for my indoor track, but It's a transmitter setting, not on the esc. Basically I set my throttle end point to 50-70% of the full speed setting which never allows the esc to get to full...
Forum: Electrics 17-09-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Are you hitting the voltage cut off for 2S? For...

Are you hitting the voltage cut off for 2S? For brushed operation on 4cell, you still have to either disable voltage cutoff or make it 1S. You really need hotwire to do these changes, and it would...
Forum: Electrics 19-07-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Good News, it's not dead. I connected the...

Good News, it's not dead. I connected the hotwire, defaulted the settings, then took it back to 212. It seemed to work ok then, so I tried the v223 update again, which worked great this time. Set the...
Forum: Electrics 14-06-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
Does anyone use/ tried the active breaking in the...

Does anyone use/ tried the active breaking in the RS pro 2.23?
What does it do and when to use it?
Forum: Electrics 13-04-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
The username I have used to register is...

The username I have used to register is "neal".
Forum: Electrics 12-04-2012
Replies: 1,800
Sticky: Team Tekin Q&A
Views: 231,892
Posted By neallewis
I can get to the tekin website fine. works ok...

I can get to the tekin website fine. works ok here.

I've also been trying to get registered on the tekin forum to ask a technical questions. You have to get approval when you register to then be...
Showing results 1 to 20 of 20

 
Forum Jump

All times are GMT. The time now is 03:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com