|
#1
|
|||
|
|||
Mugen MST-1 Electric
I made this out of Mugen MST-1 Parts. It will eventually have an Associated T4 transmission. It will also require a new rear arm mount to accomodate the T4 transmission. I was looking into the aluminum rear arm mount for the BJ4. Can any one give the measurements of the distance between the outermost screw holes?
|
#2
|
|||
|
|||
Dead sexy.
|
#4
|
|||
|
|||
Have you run it yet? Where do you plan on mounting everything?
|
#5
|
|||
|
|||
Mounting the electronics
There is a 3/4 of an inch on each side of the chassis to mount a quantum esc and a receiver. They will have to be mounted sideways standing up but it will work. Also, I plan to install a chassis protector made of lexan to protect the underside. I am currently bidding on the t4 transmission on ebay. Hopefully I'll win it and it will be the final piece to it. I'll have better pics this weekend. My only set back will be mounting the transmission since I already drilled holes too far appart on the chassis for a losi transmission. Anyways, the rear arm mount of the MST-1 is so large that I may need to find another.
|
#6
|
|||
|
|||
Quote:
|
#7
|
|||
|
|||
Arm mount
No, the arm mount was ok and I had mounted the losi transmission from under the chassis via two screws however, mounting the front of the losi transmission would have required some serious engineering since it only has a horrizontal hole where on a losi vehicle it would have a screw go through the tower, tranny, and finally motor plate. I have just bought an T4 transmission case and it seems to work perfect. It will bolt down via the two screws from under the chassis, which I have to create since they are different from what I have drilled on the chassis already. Also, it will require spacers to elevate and level the tranny to sit on the chassis. The the front side of the transmission will bolt down easily via a carbon fibre brace since its go two holes facing down. This can be accomplished with aluminum posts if not a caron fiber brace. The motor guard will have to be attached from under the chassis with two screws, which will also go through the chassis and into the transmission. The motor guard is counter sunk so it wont be too bad having extra material under the chassis to scrape the ground. It will also serve as a hold down for the lexan undertray I will create. It will also project the end edge of the chassis from scraping. In the end, the only parts I will need will be a small brace to mount the tranny. Once I design myself and make the piece, I will order spares from Fybrle Lyte in the UK with even more precise dimensions. Overall, I am satisfied that I did not have to modify the rear arm mount on the MST-1 or any other plastic components. This means that I can order spares and mount them on whenever something breaks without modifications. The only unique one of a kind pieces are the chassis, upper deck, rear small deck that holds the front of the tower and a small brace to hold down the front of the transmission. These items I will order from Fyblre Lyte as final products for no more than 70 pounds in the future. Everything else will bolt right on. I'll post pics of this by the end of the weekend. Oh, the t4 transmissino will be about 4 milimiters higher than what it usualy sits on a T4 chassis. This is in order to clear the MST-1 rear arm mount, but it is not too much difference.
|
#8
|
|||
|
|||
A few pics
A few pics
|
#9
|
|||
|
|||
Nice to see you got everything figured out. How did you make the chassis? A mill I'm guessing. I want to make one for my Scorpion truck.
|
#10
|
|||
|
|||
Chassis
The Chassis is made by Fybre lyte of the UK, I simply asked them to modify it. I asked them to not make the transmission hole nor the holes to mount the engine, or the flywheel hole. I made most of the countersunk holes myself.
|
#11
|
|||
|
|||
Oh, nice, do they do any chassis?
|
#12
|
|||
|
|||
Chassis
Well, they make stuff for all kins of vehicles. They just happened to make one for the MST1. http://www.fibre-lyte.co.uk/
|
#13
|
|||
|
|||
Finished
Here is the finished product.
|
#14
|
|||
|
|||
Two more
Two more
|
#15
|
|||
|
|||
I have contacted them and I'm getting one made for my truck. Nice, by the way.
|
#16
|
||||
|
||||
I have now driving experience of trucks, but hey, this looks like it just came outta a factory. Superb. I hope it goes as well as it looks. if it does, it will take some catching.
Just goes to show you what a bit of imagination and a fair bit of tallent can do. Best of luck with it mate, there are too few "modellers" around in this hobby these days.
__________________
schumacher procat x Two, one bosscat, one rc10 gold pan, two optima mids, one cougar/club10 |
#17
|
|||
|
|||
Thanks
Thanks, I'll install electronics today. I was going to go brushless. but I've opted for a nice Futaba MC800C, and a chekpoint motor. Also, spektrum dx2 for the radio and a ko propo 2343 servo.
|
#18
|
|||
|
|||
Can you get a video of it?
|
#19
|
|||
|
|||
No video camera
No video camera, but here it is with electronics ready to go.
|
#20
|
|||
|
|||
two more
Two more
|
|
|