Go Back   oOple.com Forums > General > 1/10th OFF ROAD

Reply
 
Thread Tools Display Modes
  #1  
Old 03-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default Too many questions for one forum, please help!!

Yet again I seem to be showing my lack of knowledge on undertaking a Schumacher KC build and need some help.

I've been looking for some name stickers for my shell. Looking around the forums I've tried to contact Oople who do them (or at least used to) without a response. Are there any dependable places to get these from? Basic One line name with a flag would do for me.

I've been getting some parts together to build this thing and have failed to realise till it was too late that to compete they would need to be Roar specified. Because of this I bought another ESC, Corally Pro 120a, and a 17.5t Trinity Monster, but would like to swap it with a 7.5t Reedy or similar back and forth. Because of the need to swap I can't directly solder the ESC and motor and need to resort to connectors. I've basicly exhausted what I can find on the subject and would like a bit of help if at all possible. I've concluded that ideally I would need 10awg wire, but it's difficult to work with and solder to the motor and ESC, so I've settled on 12AWG wire. This leads to the connectors required for the Amps I'll be running. The Reedy would need 63 amps continuous so can I assume 4mm bullet connectors will work? Also if bullet connectors are the way to go does heat shrink provide enough insolation for the connectors to stop them shorting? All the good connectors don't seem to come with covers.

Lastly I'm having a go at painting a shell for it. I'm not the best, but was able to go a great job on a Rapid Fit Mondeo shell for my TT-01. If all else fails are there any good places to go for a custom shell?

Thanks again for the help.

Last edited by Infinitesd; 03-09-2018 at 12:09 PM.
Reply With Quote
  #2  
Old 04-09-2018
mattr mattr is offline
Mad Member
 
Join Date: Mar 2011
Location: Sweden
Posts: 1,838
Default

You can use 14AWG in 2wd without any issues, 12AWG is "better" if you have long cable runs. Which you should try and avoid anyway.
10AWG is really for continuous high drain applications, i don't even use it in a 4s 8th scale.

I also have used 4mm bullet connectors in line to enable motor swaps, but i use the heat shrink as a complete sleeve over each connector, it means i need to cut the tube to swap motor, but experimenting with just trying to insulate the connector just leads to the connector sliding apart under big impacts and shorting out. So a full sleeve solves both issues......

I gave up eventually, as it was just a pain in the arris to swap motors, pinions, changing set up on the ESC etc. So i bought a second car,
Reply With Quote
  #3  
Old 04-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default

Quote:
Originally Posted by mattr View Post
You can use 14AWG in 2wd without any issues, 12AWG is "better" if you have long cable runs. Which you should try and avoid anyway.
10AWG is really for continuous high drain applications, i don't even use it in a 4s 8th scale.

I also have used 4mm bullet connectors in line to enable motor swaps, but i use the heat shrink as a complete sleeve over each connector, it means i need to cut the tube to swap motor, but experimenting with just trying to insulate the connector just leads to the connector sliding apart under big impacts and shorting out. So a full sleeve solves both issues......

I gave up eventually, as it was just a pain in the arris to swap motors, pinions, changing set up on the ESC etc. So i bought a second car,
Thanks for the advice.

I've often thought about a second chassis like maybe 2wd Associated B6D, but I really don't have the resources to run two machines (as tempting as it might be), that and trying to explain to the wife on how these two buggies are similar, but different wouldn't go down very well. It's a shame that these buggies are so specialised that you can't run in either conditions.

I'll try the full sleeve heat shrink for now and see how it goes. I'm guessing I can always resolder a direct connection in the future if I find I only run one motor. I finally received my ESC as well and it comes with wires and a capacitor to use (gonna have to research how to install that one now) so that sorts the wire issue as well.

As for the decals I found RC decals looking at the forum. I'll see how those work, very easy to order, and was able to design my own (within reason).

Just need a paint design now.
Reply With Quote
  #4  
Old 04-09-2018
Yorkiebar Yorkiebar is offline
Member
 
Join Date: Mar 2018
Posts: 264
Default

Just a quick point - are you based in the USA by any chance? Confused as you mentioned ROAR but then threw me with a Rapid Fit Mondeo livery.
Reply With Quote
  #5  
Old 04-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default

Quote:
Originally Posted by Yorkiebar View Post
Just a quick point - are you based in the USA by any chance? Confused as you mentioned ROAR but then threw me with a Rapid Fit Mondeo livery.
Sorry I'm American, but live in the UK so I'm always drifting between the two when I talk. I meant BRCA approved. I think with most things ROAR and BRCA seem to have similar rules and accepted motors, etc..
Reply With Quote
  #6  
Old 04-09-2018
Yorkiebar Yorkiebar is offline
Member
 
Join Date: Mar 2018
Posts: 264
Default

Ha, no worries - was just going to point out that you don't need ROAR approved kit in the UK.

Even then, unless you're doing regionals / nationals, or race at a club that has hard ruling then the BRCA approved stuff doesn't matter either - the club I race at the only stipulation they make is hardcase lipos and charging in lipo safes.
Reply With Quote
  #7  
Old 04-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default

Quote:
Originally Posted by Yorkiebar View Post
Ha, no worries - was just going to point out that you don't need ROAR approved kit in the UK.

Even then, unless you're doing regionals / nationals, or race at a club that has hard ruling then the BRCA approved stuff doesn't matter either - the club I race at the only stipulation they make is hardcase lipos and charging in lipo safes.
I didn't know that, though the closest club to me doesn't appear to have my class either, so I'll need to go hunting.
Reply With Quote
  #8  
Old 04-09-2018
pumbaa pumbaa is offline
Member
 
Join Date: Aug 2015
Location: Weston-super-Mare
Posts: 126
Default

Where in the UK are you then?

Plenty of people who can do you a shell, on here or the book of face.
Reply With Quote
  #9  
Old 05-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default

Quote:
Originally Posted by pumbaa View Post
Where in the UK are you then?

Plenty of people who can do you a shell, on here or the book of face.
I'm in the NE. I've done shells in the past, and will try at least one before I give up, but a lot of the designs these days seem to be airbrushed and very detailed compared to a masking tape and rattle can approach.

On another note, just started my build last night and got the steering servo centered and horn assembled. I've heard you want to put thread lock on the screw, but both Schumacher and Corally seem to advise against this. Guess I'll try it without and see how it holds up.

Funny thing is I didn't seem to care when I put my TT-01E together, but I seem to be getting a bit retentive (of the backside variety) in my old age.
Reply With Quote
  #10  
Old 05-09-2018
Yorkiebar Yorkiebar is offline
Member
 
Join Date: Mar 2018
Posts: 264
Default

Quote:
Originally Posted by Infinitesd View Post
I didn't know that, though the closest club to me doesn't appear to have my class either, so I'll need to go hunting.
1/10th off road 2WD?

There's a couple up there...

http://www.newcastlercracers.uk/

http://www.neam.esy.es/Welcome.html

A bit further South you have Robin Hood Raceway, a huge outdoor astro track.

http://robinhoodraceway.com/
Reply With Quote
  #11  
Old 05-09-2018
Infinitesd Infinitesd is offline
New Member
 
Join Date: Aug 2018
Posts: 13
Default

I found NEAM, and Robinhood raceway is very nice! Thanks for the links, I'll need to make some inquiries.

Just to add, the stickers from RC decals came, and they are extremely good. I'm gonna get some more as the current batch are being stuck on tool boxes, receivers, and anything else with a flat surface.

Last edited by Infinitesd; 05-09-2018 at 07:50 PM.
Reply With Quote
  #12  
Old 24-09-2018
Cookie1892 Cookie1892 is offline
New Member
 
Join Date: Jan 2016
Posts: 17
Default

Quote:
Originally Posted by Infinitesd View Post
I found NEAM, and Robinhood raceway is very nice! Thanks for the links, I'll need to make some inquiries.

Just to add, the stickers from RC decals came, and they are extremely good. I'm gonna get some more as the current batch are being stuck on tool boxes, receivers, and anything else with a flat surface.
Where abouts in the North East are you?

A lot of us run the KC at NEAM so plenty of help around for you.


Join the facebook group as well
Reply With Quote
  #13  
Old 25-09-2018
revol revol is offline
Member
 
Join Date: Feb 2014
Location: North Yorkshire
Posts: 69
Default

There's also weekly Saturday night indoor races during term time at Yorcc, Huntingdon school.
Reply With Quote
  #14  
Old 27-09-2018
mattr mattr is offline
Mad Member
 
Join Date: Mar 2011
Location: Sweden
Posts: 1,838
Default

Huntington School.

Huntingdon is about 150 miles out of your way

Though nothing good has EVER come out of Huntington School. Ever.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 07:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com