|
#41
|
||||
|
||||
Damn...you're using all my RC10T parts..! 😂
__________________
Team Associated B6 Team Associated B5m Centro C4.2 Team Associated B4.2 RC10 Worlds |
#42
|
||||
|
||||
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#43
|
||||
|
||||
RPM 91 w0RldS Front End.
RPM 91 w0RldS Front End fitted. The front screw is longer on the right, this will allow for the body mounting post to fit on top of the steering bellcranks.
Nose tubes require the mod to fit in to the RC10T Bulkhead. Once the Yellow A & L steering turns up I will fit it and show. CLICK TO ENLARGE PICTURES...
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#44
|
||||
|
||||
Looking good!! Some nice rare parts on this build
|
#45
|
||||
|
||||
A & L Steering...
A & L yellow steering turned up today.......
I will be fitting these later with LUNSFORD 7 turnbuckles and RPM Ball ends.... CLICK TO ENLARGE PICTURES......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#46
|
|||
|
|||
Will you race it when finished ? loving the build ! Awesome
|
#47
|
||||
|
||||
Thank you Nige55,
Yes it will be run/raced......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#48
|
||||
|
||||
A & L Steering...
A & L Steering fitted, LUNSFORD 7 turnbuckles and RPM Ball ends.
New castor blocks and steering arms fitted. Just need to make alterations to the nose tubes, then install, then the front body post to install on top of the bellcrank..... Ive fitted a 2nd battery cup with them cut down to allow for the REEDY shorty. I have fitted them to allow for the foam spacer to fit forward and back...... CLICK TO ENLARGE PICTURES......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#49
|
||||
|
||||
VTS Slipper
So just a small up date.
VTS Slipper fitted to the Original STEALTH gearbox with RDRP Vented front pad and Associated drilled rear pad.. HYDRA-DRIVE Gear cover on the way from America.... Front shock mount screws and bushings ready for the Associated BIG BORES.. CLICK TO ENLARGE PICTURE....
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#50
|
||||
|
||||
Looks awesome.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#51
|
|||
|
|||
Gorgeous. Absolutely perfect build with all the best bits. Love it. There's something about that slipper and vented pad that's just lush on a stealth 'boxed RC10.
|
#52
|
||||
|
||||
Cheers Lads.......
So I have made a little change. I have removed the LUNSFORD 7 turnbuckles and have fitted the TECHNACRAFT turnbuckles instead. I just prefer these. I have now completed the mod to the nose tubes and fitted. Ive messed around for a few hours with the BIG BORES, Different Bodies, shafts and internal spacers to get the up-travel and droop I wanted on the Front.... I have also fitted RC10 Worlds rear hubs and bearings to allow for the RC10 B3 axles to allow me to run the Original Proline and Associated Wide body wheels. I have also fitted the RPM rear shock tower. I wasn't going to use it, I was going to fit a standard RC10 Team rear tower. But hey !!! its fitted..... Pictures coming now !!!!!!!!!!!!!
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** Last edited by xfactor; 11-11-2018 at 06:38 PM. |
#53
|
||||
|
||||
That slipper nut looks tight..! ..and what are those scratches on the motor plate...!...😂......still looks great though..👏
__________________
Team Associated B6 Team Associated B5m Centro C4.2 Team Associated B4.2 RC10 Worlds |
#54
|
||||
|
||||
Here you go.....
CLICK TO ENLARGE...........
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#55
|
||||
|
||||
Quote:
The slipper nut looks tight, but the spring sits a good way into the RDRP outer plate. I was thinking once its set trimming the shaft down to neaten it up a little, but will leave it till I have power through it and ran it. The anodising is rub marks from use. When the motors fitted and gear cover is on you wont see it............ This is my runner Aire. The one I will be building for the shelf hasn't any scratches or marks.......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** Last edited by xfactor; 10-11-2018 at 08:54 PM. |
#56
|
||||
|
||||
Not just one..but two like that..!..👏👏.. I don't believe it...!
__________________
Team Associated B6 Team Associated B5m Centro C4.2 Team Associated B4.2 RC10 Worlds |
#57
|
||||
|
||||
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#58
|
||||
|
||||
HYDRA-DRIVE Gear Cover RC10.
So the Team Losi HYDRA-DRIVE Gear Cover for the RC10 STEALTH Gearbox came today.
It will cover the VTS perfectly while still giving the Vintage look..... Cut out ready to mount........ CLICK TO ENLARGE PICTURES......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#59
|
||||
|
||||
Fitted.
HYDRA-DRIVE Gear Cover fitted. Also the gearbox brace and rear body mount fitted.....
Perfect fit......... CLICK TO ENLARGE......
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** Last edited by xfactor; 12-11-2018 at 08:14 PM. |
#60
|
||||
|
||||
Shocks
So after purchasing some B5M shocks on here, that actually were B6 shocks , Ive now managed to sort them out.
The front BIG BORES are B6 rears with B6 front shock shafts. The rear BIG BORES are now B5M bodies with B6 rear shafts etc.... They are now fitted to the RPM RC10 91 worlds and just waiting for the wing tubes to turn up. So almost there with the build. I have the B3 wide body pro-line original wheels to fit. I will sort pictures tomorrow of the above up-dates...........
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
Thread Tools | |
Display Modes | |
|
|