|
#881
|
||||
|
||||
Some pics of brass pieces for the James Lazer I thought I would share with the Lazer fans here
|
#882
|
||||
|
||||
Superb!!! As ive always said there are not many people as gifted as you with making components. Can you email these so i can get a better look. Thanks
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#883
|
||||
|
||||
James I already did through my normal mail
|
#884
|
|||
|
|||
Missed Kyosho Lazer TOP Shaft!
Guys,
I am so Mad at My Self. I just missed an auction for a Kyosho Lazer Top Shaft on Ebay Auction#160445081487. Look at the Top RIght Corner, and its the Peak Performance Top Shaft. Is there anything compatible? The whole lot sold for 10 Dollars!.I know I cant win them all. Any suggestions? Anything compatible? Thank you |
#885
|
|||
|
|||
Suspension Shaft
Hi Guys,
I am trying to rebuild my Lazer ZX-R, but i've hit a bit of a problem. The shafts that holds the front wishbones to the car (Part # LA-20) have bent badly. I can't find any replacements and i'm wondering what everyone here does? Do you all just have spare packs of LA-20's or are there spares from other models that will fit and will be easilly available? Regards, Nick |
#886
|
||||
|
||||
Quote:
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#887
|
||||
|
||||
Quote:
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#888
|
|||
|
|||
Quote:
I hope they will perform as good as they look . Bye Ema |
#889
|
||||
|
||||
Error
See below
Last edited by rondoolaa; 05-07-2010 at 12:01 PM. Reason: Wrote out wrong |
#890
|
||||
|
||||
Quote:
Nick, goto your local hobby store and take one with you and they should sell steel bars approx 1 metre in length, approx £1.20 a metre buy one that is the approx diameter and cut to size, that's what I did as the only place I could find selling the originals was in the states... Ron Last edited by rondoolaa; 05-07-2010 at 12:12 PM. Reason: none |
#891
|
|||
|
|||
Hi,
Thanks for all the advise. I checked out all the manuals for current 1/10 models from Kyosho website, the Lazer and Ultima shafts are too short, however i have found that the DBX/DRX rear shafts are 3mmx56mm so can be cut down to 50mm for Lazer ZX-R. However, i ended up buying metal rod. Unfortunately there are NO model shops where i live (Jersey Channel Islands) and as such only had B&Q, smallest rod they do was 4mm Dia, but god bless eBay! Three 3mmx30mm stainless shafts for £2.50, bargain! Anyway cutting a long story short, 3mm Stainless rod from ebay works a treat, just dremmel to 50mm lengths. Hope this helps someone else having the same problems. Once again, thanks everyone for your contribution, much appreciated. I'll post some pics of the rebuild, hopefully this week, i'm so pleased with it, it was a great car, and will be again |
#892
|
||||
|
||||
glad you got it sorted
glad you got it sorted, i would have sent you some out if you couldnt get any, i cut loads from 1 rod, also i got a rod 1mm-2mm smaller in circumference so they are not as tight a fit as the originals...
|
#893
|
|||
|
|||
I just thought it might be better for my Kyosho Lazer ZX to have a Top Shaft.
THank you Last edited by trd179v; 06-07-2010 at 07:21 AM. Reason: Forgot Reference |
#894
|
||||
|
||||
Im kindof confused. Does your zx have the standard layshaft with 100t spur gear with alloy balls all around as if yes its most probably the best slipper you can have for the lazer
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#895
|
|||
|
|||
Thank you for the Input. Much appreciated.
|
#896
|
|||
|
|||
Zx-s super rare chassis on ebay
I think it's time for our Zx-s guys to bring some money out from their wallet !!!
http://cgi.ebay.co.uk/ws/eBayISAPI.d...m=250671064778 Bye Ema |
#897
|
||||
|
||||
Not worth it. Fibrelyte do an exact copy at a fraction of the cost and is a lot stronger than the kyosho version. You most probably can still buy the original through kyosho in your country for a third less as japan does keep stock of stuff like that.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#898
|
||||
|
||||
Still cool but is that original on the evo ??? to be able to move the batteries ???
I have just not sean one before. mvh Isobarik |
#899
|
||||
|
||||
Guys this will not work with any Lazer modwls except the ZXS. The ebay seller was misinformed.
Yes this was made but prefer my own design. The brace goes under the chassis which put me off. Still kyosho may still have stock for a lot less.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#900
|
||||
|
||||
Welsh
Hope soo since it was ridiculus over priced you get 2 chassis from fiberlyte ok you get one law 20-1.....with the chassi but they can be bought from manolis for an example ...anyway those brass reargearbox sides should look awsome against the blackcarbon build it damn build it ..... Welsh do you have some conections with kyosho japan ???? Have you heard anything from keith about the zxr and tomcat.... Still have the racetech body uncut and clear will send it to him as soon as the zxr are ready/finnished mvh isobarik |
|
|