Stampy chit chat

[jhammond]

Stampy... Not that I want to prevent a possible purchase of bearings from a certain someone here...

But why on earth are you enquiring about bearings for the B4 and Madrat? You said just days ago these are up for sale?


Julius.

[stampede vxlboy]

my son got a new madrat fit for xmas and the wife got a b4 kit for xmas

[jhammond]

Ah...

I see... No worries.


Just try to focus on the XXX4 you purchased now... Honestly: You don't need to buy lots of unnecessary stuff; just take it down to the club and you'll find it's a 'comfy' little car.


Julius.

[stox217]

Originally Posted by stampede vxlboy

my son got a new madrat fit for xmas and the wife got a b4 kit for xmas

[stampede vxlboy]

thanks mate wife wanted to race as well

[mark christopher]

stampy not being funny but............

you could have let you misses have the b4 you have and buy a new shell and save some bucks??
like wise with your sons madrat

[stampede vxlboy]

Originally Posted by jhammond

Ah...

I see... No worries.


Just try to focus on the XXX4 you purchased now... Honestly: You don't need to buy lots of unnecessary stuff; just take it down to the club and you'll find it's a 'comfy' little car.


Julius.

i will but it outdoor tracks i just wanted to know if you could put a xx4 chassis on the xxx4 it look mini in the pictures plus it got the top line losi shock

[jhammond]

Originally Posted by mark christopher

stampy not being funny but............

you could have let you misses have the b4 you have and buy a new shell and save some bucks??
like wise with your sons madrat

^I came to this conclusion too... But I lost hope months ago.




Julius.

[barry]

Originally Posted by stampede vxlboy

my son got a new madrat fit for xmas and the wife got a b4 kit for xmas

Sounds expensive stampy - it's a shame you don't all have the same buggy. Would save a fortune on spares not to mention setup knowledge etc!

Barry

[Col]

Originally Posted by stampede vxlboy

i will but it outdoor tracks i just wanted to know if you could put a xx4 chassis on the xxx4 it look mini in the pictures plus it got the top line losi shock

No. Why would you want to anyway?

The best of both worlds would be the xxx4 chassis and the xx4 suspension.

Hang on! It's called an x5, built by xfactory!

[stampede vxlboy]

the x5 parts are hard to get hold of

[jhammond]

Originally Posted by stampede vxlboy

the x5 parts are hard to get hold of

Is this a question? Or statement.

I presume it's a statement; because you've already purchased a xxx4?

[stampede vxlboy]

yes it is mate x5 part are too hard to get hold of them

[stox217]

most x5 parts are losi.
as an x5 is a conversion kit.

[Battle_axe]

sorry to break up the party i started this thread as a setup thread for the madrat\xpro and stampy u have abused it with all your lossi rubbish get an x5 there better then the xx4 done finished

[stampede vxlboy]

sorry but it was other people as well and sorry for this but the xxx4 is ten times better than a madrat mate end of back to the madrat i would buy a better motor than a 9turn is the same as a 10 turn brushed. as its a 380 can size mate get the 6.5 or 5.5turn or 8.5 turn as the 9 turn is slow. i did have 2 of them and i have sold the motors as its a very small motor and nothink like a 9 turn 540can . ezrun 8.5turn combo with a esc that 60amps and the 9turn combo is 35amps go for the bigger size can as you will be dissapointed with the out put power and you cannot use them for racing at all as it sensorless

[sparrow.2]

This thread is supposed to be about shock oil, damper mounting positions, weight distribution etc.

Stampy you are going to no doubt cock up the xxx4 like all your other cars and never race it so please confine your posts to the playground where people can have a laugh. Any car surpasses your driving ability at the moment so you have abolutely no legitimation of spouting opinions as to which car is better than whatever other car.

I for one would be really interested in seeing how people are setting up their Madrats and not having to wade through this rubbish thread only to find that it has been ruined with the usual drivel...

[sparrow.2]

Originally Posted by stampede vxlboy

sorry but it was other people as well and sorry for this but the xxx4 is ten times better than a madrat mate end of back to the madrat i would buy a better motor than a 9turn is the same as a 10 turn brushed. as its a 380 can size mate get the 6.5 or 5.5turn or 8.5 turn as the 9 turn is slow. i did have 2 of them and i have sold the motors as its a very small motor and nothink like a 9 turn 540can . ezrun 8.5turn combo with a esc that 60amps and the 9turn combo is 35amps go for the bigger size can as you will be dissapointed with the out put power and you cannot use them for racing at all as it sensorless

Senseless bullshit

[stampede vxlboy]

back to the madrat you cannot use a sensorless sytem to race with at most clubs

[steelie600]

why not stampy, is sensorless dabgerous or summat? enlighten me