|
#21
|
||||
|
||||
The only way the upper deck doesn;t line up is if after you glue the edges, you then don't sand or remove the glue from the fore and aftmost edges where it slots into the slipper mount and gearbox locations.
Having built 3 in 2 days recently, I can honestly say. Not one bit didn't fall into place... The dremel file or 'force' were never used....
__________________
5 Time Oople Invernational SC Champion. Powered by OptiPower Do, or do not, there is no try! |
#22
|
|||
|
|||
I did'nt even put glue on...
I used Z-42 Thread Lock and they were backing out... I'm just gonna go to A Red Permanent... (I get free parts) if i ever need to replace it... Also, I was using losi wheels all around and all the wheel nuts were backing off after a minute or two of running...I brought it back to the pits and one of the wheels fell off. Two times the wheel pins in the rear just flew off when i was running... This sucks because most of my wheel stock is losi. |
#23
|
|||
|
|||
ive never found the driveshaft pins to come off mine, but i did find that my good hex driver couldn't get to the grub screw properly and tighten, it was too thick and rigid (urgh). using a smaller allen type one worked a treat.
hope that helps someone |
#24
|
|||
|
|||
I'm gettin way better with the car, everytime I drive it and work on It!
|
#25
|
|||
|
|||
Hi, im after more steering (indoors), but still want the car to have a responsive feel so i dont want to soften the front too much
im guessing going to the lower castor setting? or should i be leaving it on 10 degrees and adjusting other things? thanks |
#26
|
||||
|
||||
Depending on where you are wanting the steering.
Going in to the corner - Reduce Castor to 7 Degrees - Lower the inner Ballstud - Raise the Outer Ballstud - Add a touch of Toe-out. Coming out of the Corner - Increase Castor - Tighter front diff - Reduce front droop You don't have to soften the car off. Softening it off can make the car roll more and transfer less weight to the outside wheel. It's a balancing act...
__________________
5 Time Oople Invernational SC Champion. Powered by OptiPower Do, or do not, there is no try! |
#27
|
||||
|
||||
Quote:
as adam said i left the springs and damping, but my teacher is the above poster
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#28
|
|||
|
|||
cheers for the advice,
mid to exit steering is what im after, i think anyway...so ill leave caster at 10 it seems like the car is going a little wide on power through the corner, by reducing the droop, would that be adding some limiters inside the front shocks, if so should I balance the rear with the same amount? ta |
#29
|
|||
|
|||
you need a washer under the wheel nut if you are using losi wheels.
The losi wheel is thiner in the boss area so the nut bottoms out on the sholder and does not tighten the wheel enough. You will also strip the hex if you do not use a washer under the nut. Phill Truman |
#30
|
||||
|
||||
Quote:
As for the rear. No need to alter the rear droop. Unless your car is pitching forward too much under braking. Also, depending how bumpy the track is, you may need droop.
__________________
5 Time Oople Invernational SC Champion. Powered by OptiPower Do, or do not, there is no try! |
#31
|
||||
|
||||
To get more steering you have also the option to tighten the rear diff a bit.
Had the same issue last weekend and this improved the steering on corner exit on throttle and the back of the car just follows your steering nicely. This will make a different effect depending on the traction of the track! Also I would not suggest the 7 degree caster blocks, 10 is perfect together with very little toe out! |
#32
|
|||
|
|||
I have a question about Ball stud position and camber link length
1. Why are people working so hard to lower the inside ball stud height and raise the outer? 2. I see some use the short rear camber link and some use the long so why do you use either one. |
#33
|
||||
|
||||
Hi all.
In 2 weeks finally I'm going to run with my D4 WCE in the new circuit of Bilbo's Club Carbi (The 2009 Euro Circuit) and I would like to know if anyone have a good setup for running over Astroturf?. Regards.
__________________
VF PHANTOM MKII 4WD. |
#34
|
|||
|
|||
Hi all,
In a Setup of Adam Skelding stand "Piston: 3x #55 and 3x #56". What does that mean? I only know the 1-3 Pistons uf HotBodies. thanks! |
#35
|
||||
|
||||
they refer to losi piston sizes, IE drill bit sizes,see attachment bellow
|
#36
|
|||
|
|||
Indoor slippy set up
I'll be driving indoors on a medium/slippy surface which'll be tight also.
I've sussed out tires but i'm not sure where would be a good place to start in terms of set-up. Can anyone point me in the right direction please Thanks |
#37
|
||||
|
||||
I got my D4 2nd hand and Im a complete noob...worse, an old noob!
I can sort of understand the things some of you guys recommend to get better steering, mines has a very wide turning circle and could do with a lot less understeer. I've downloaded the setup sheets but have no idea where to start as a baseline, I dont think the buggy is set up right when the understeer is as mad as mines is! The transmission feels/sounds fine and it will whack off down the track dead straight, no wandering and plenty of power. Its just the steering for me? I'de be happy to have a working point to start from, the I can change things and log them on the startup sheet, and know rather than guess where I am and where we are going with the adjustments. Didnt get a manual, having to work off the parts diagram and reviews of the buggy. |
#38
|
||||
|
||||
make sure you have a good steering servo, and the servo saver is not loose, it needs to be tighter then the manuals setting,
they do understeer, one of its traits
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#39
|
||||
|
||||
Manual download from here: http://www.hbeurope.com/manuals/61410.pdf
other gumph that may be interesting: http://www.hbeurope.com/kit.php?partNo=61410&lang=en setup wise I would think BJ4,s or B44's would be very close, D4's and B44's being a bit BJ4ish. |
Thread Tools | |
Display Modes | |
|
|