Go Back   oOple.com Forums > Car Talk > Xtreme - VEGA

Reply
 
Thread Tools Display Modes
  #1  
Old 20-10-2006
jimmy's Avatar
jimmy jimmy is offline
Administrator
 
Join Date: Oct 2005
Location: Huddersfield
Posts: 10,047
Blog Entries: 6
Exclamation Setups

This is a sticky thread for posting setups only please!
Reply With Quote
  #2  
Old 15-04-2008
mattym0310's Avatar
mattym0310 mattym0310 is offline
Mad Member
 
Join Date: Jan 2007
Location: York
Posts: 1,470
Send a message via MSN to mattym0310
Default

Batley Outdoor

Springs: 6t
Pistons: Hard + Valve
Oil: 35 Associated
Toe: In 1 Degree
Camber: 2 Degrees
Castor: 0 washer behind wishbone
Ground clearance: 16mm
Anti Roll Bar: None


Rear:

Springs: 5.5t/Gold
Pistons: Two hole, no groove
Oil weights: 50wt Associated
Toe-in per side: 3 Degrees
Camber per side: 2 Degrees
Ground clearance: 22mm - or a little more if it cuts up.
Anti-roll bar: None
Rear lower upright: Upper Hole
Damper pickup point: Middle
__________________
Matt Myers

Team Associated b4
Team Associated b44
Reply With Quote
  #3  
Old 15-04-2008
mattym0310's Avatar
mattym0310 mattym0310 is offline
Mad Member
 
Join Date: Jan 2007
Location: York
Posts: 1,470
Send a message via MSN to mattym0310
Default

Worksop Indoor

Front

6 turn springs
Kit pistons & rebound valves
30 wt oil
Push rods mounted on top of rockers
0 degree toe in - may need 1 deg toe-out
-1 degree camber
Castor - right back
14mm ride height - or lower at Worksop depending on bumps, but ride height has a big influance on steering on the Pred as you probably know.


Rear

5 1/2 turn springs & pre springs
Kit pistons
45 wt oil
Middle hole rockers
4 degrees toe-in per side
-1 degree camber
22mm ride height - or lower at Worksop, but drop front and rear the same.
__________________
Matt Myers

Team Associated b4
Team Associated b44
Reply With Quote
  #4  
Old 15-04-2008
mattym0310's Avatar
mattym0310 mattym0310 is offline
Mad Member
 
Join Date: Jan 2007
Location: York
Posts: 1,470
Send a message via MSN to mattym0310
Default

Southport Outdoors

Front

5.5 turn springs
Kit pistons & rebound valves
30 wt Losi oil
Kit rockers (push rods mounted on top)
1 degree toe in
-2 degree camber
Castor – 4 washers in front, 3 behind
Front pushrod length - 30mm


16mm ride height


Rear

5 1/2 turn springs & pre springs
Kit pistons
50 wt losi oil
Middle hole rockers
2 degrees toe-in per side
-2 degree camber
22mm ride height
Maximum Droop
Kit Anti Squat

[Courtesy of Peter Ellis]
__________________
Matt Myers

Team Associated b4
Team Associated b44
Reply With Quote
  #5  
Old 15-04-2008
mattym0310's Avatar
mattym0310 mattym0310 is offline
Mad Member
 
Join Date: Jan 2007
Location: York
Posts: 1,470
Send a message via MSN to mattym0310
Default

Coventry Outdoors

FRONT:

Caster: 5 washers back, 1 forward
Push rod placement: mounted on top of the rocker.
Roll-bar: none
toe in: 1degree
ride height: 18mm
camber: 2degrees
Springs: 5.5t black
Oil: Associated 35wt
pistons: kit
1 way unit in the front, fixed prop shaft.

REAR:

Roll bar: yes- soft setting.
Toe in: 2degrees
ride height: 23mm
camber: 2degrees
Anti Squat: 3.5 degrees
Shock pick up position: middle hole
hub pick up position: upper hole
springs: 6.5t black
Oil: associated 30wt.
Pistons: 2 hole - kit

[courtesy of Tom Yardy]
__________________
Matt Myers

Team Associated b4
Team Associated b44
Reply With Quote
  #6  
Old 15-05-2008
Mrs.TeamXtreme's Avatar
Mrs.TeamXtreme Mrs.TeamXtreme is offline
Senior Member
 
Join Date: Apr 2008
Location: EYTHORNE
Posts: 427
Default Southport Outdoors By Tom

Front

6 turn springs
Kit pistons & rebound valves
35 wt associated oil
Kit rockers (push rods mounted on top)
1 degree toe in
-1 degree camber
Castor – 4 washers in front, 3 behind
Front pushrod length - 30mm
16mm ride height

tyres: worn yellow mini spikes

Rear

5.5 turn springs & pre compression springs
Kit pistons
50 wt Schumacher oil
Middle hole rockers
1 degrees toe-in per side
-1 degree camber
22mm ride height
Kit Anti Squat
3mm droop

Tyres: worn yellow mini spikes

Nosram evo 2007 with 6.5
Spur 72t
Pinion 19t
IB 4200 cells
__________________
SEX11 - Probably the fastest car in the World in it's class!

http://www.teamxtreme.co.uk
Reply With Quote
  #7  
Old 15-05-2008
Southwell Southwell is offline
*SuPeRsTaR mEmBeR*
 
Join Date: Nov 2005
Location: Basingstoke
Posts: 4,123
Send a message via MSN to Southwell
Default

Might be useful having the type of track, track conditions etc on each setup otherwise people wont know what type of track the setup is for.
Reply With Quote
  #8  
Old 03-06-2008
Lowie's Avatar
Lowie Lowie is offline
Mad Member
 
Join Date: Jun 2007
Location: Dworp, Belgium
Posts: 1,183
Default

dito
Reply With Quote
  #9  
Old 03-06-2008
Tom3012 Tom3012 is offline
Mad Member
 
Join Date: Aug 2007
Location: Sunny southport
Posts: 1,747
Send a message via MSN to Tom3012
Default

Quote:
Originally Posted by Mrs.TeamXtreme View Post
Front

6 turn springs
Kit pistons & rebound valves
35 wt associated oil
Kit rockers (push rods mounted on top)
1 degree toe in
-1 degree camber
Castor – 4 washers in front, 3 behind
Front pushrod length - 30mm
16mm ride height

tyres: worn yellow mini spikes

Rear

5.5 turn springs & pre compression springs
Kit pistons
50 wt Schumacher oil
Middle hole rockers
1 degrees toe-in per side
-1 degree camber
22mm ride height
Kit Anti Squat
3mm droop

Tyres: worn yellow mini spikes

Nosram evo 2007 with 6.5
Spur 72t
Pinion 19t
IB 4200 cells

hi guys...

that my set-up for southport...

southport is a mixture of surfaces, mainly astro and grass with a couple of othe sections made up of cobbles, tarmac and concrete..

this set-up was used on a dry and sunny day, with plenty of grip on the track, however it does also work well in damp conditions as it makes the car a little less likely to suffer from grip role etc....

hope this helps

Tom
__________________
Team Losi Racing, Horizon Hobby
TLR 22 5.0, TLR 22X-4, TLR 22-4, 22-4 2.0

Atomic Carbon S2, S44, Vega B4.1

Trader feedback: http://www.oople.com/forums/showthread.php?t=19374
Reply With Quote
  #10  
Old 11-06-2008
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

here is a starting point for the new shocks on the x11 working both on flat grass and epr as well

front

springs blue (no compreision spring) 5 1/2 turn in older style
oil 25wt losi
piston kit with standard rebound valve
pushrod above rocker
pushrod lenth 33mm with shockball undone 1turn
revised front arms with 1 washer behind wishbone
cone washer replaced with 4 losi gold ballstud washers. 2 under outer ball with 2 above
extra midde hole drilled for roll bar
roll bar 1.2mm (standard) middle hole
ride height 19-20 mm
front wing kit with standard lines followed
slight toe out with 2 degrees of camber

rear

springs blue (no compresion spring) 5 1/2 turn in older style
oil 30-32.5 losi(depending on jumps)
piston kit
lower hole on shock mount
roll bar 1.2mm again in middle hole in lowered position (pic to follow)
wheelbase lenthened 1mm
ride height 22mm
1.5mm rear block (reduces on power steering)
large rear wing with full guerney
toe in to middle of front wheel
rear uprite in upper hole

shumacher yellow minispikes with outside outer row cutoff rear and 2 inner and outer cut off front

any extra info you need feel free to ask or pm

Nathan
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline

Last edited by niggs98; 12-06-2008 at 08:48 AM. Reason: to keep everyone happy about the bits i missed lmao
Reply With Quote
  #11  
Old 12-06-2008
Lowie's Avatar
Lowie Lowie is offline
Mad Member
 
Join Date: Jun 2007
Location: Dworp, Belgium
Posts: 1,183
Default

thx

what is "epr"?
and what can the Blue spring be compared at, in terms of the old springs?
Reply With Quote
  #12  
Old 12-06-2008
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

epr is eden park raceway (high bite astroturf and multi surface track) the springs now come colour coded so i will find out the turn equvalent when i get home but they are 1 down from stiffest
hth
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #13  
Old 12-06-2008
jeff jenkins jeff jenkins is offline
Member
 
Join Date: Apr 2008
Location: everett, WA U.S.A.
Posts: 104
Default

lower hole on rear hub or shock mount rocker?
__________________
RC US Imports - Sworkz USA- Maclan Racing- Bellgate Distributors.
Reply With Quote
  #14  
Old 12-06-2008
Northy's Avatar
Northy Northy is offline
Super Moderator
 
Join Date: Nov 2005
Location: Malton, North Yorkshire - Gods Country
Posts: 8,364
Blog Entries: 15
Default

I *think* the blue spring would be the 5 1/2 turn 1.3mm spring

G
Reply With Quote
  #15  
Old 12-06-2008
Northy's Avatar
Northy Northy is offline
Super Moderator
 
Join Date: Nov 2005
Location: Malton, North Yorkshire - Gods Country
Posts: 8,364
Blog Entries: 15
Default

Quote:
Originally Posted by jeff jenkins View Post
lower hole on rear hub or shock mount rocker?
He means on the rear rocker

Just noticed he forgot to mention the rear upright hole

G
Reply With Quote
  #16  
Old 12-06-2008
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

setup eddited for the above questions
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #17  
Old 12-06-2008
ads0021 ads0021 is offline
Member
 
Join Date: Mar 2008
Posts: 90
Default

Where did you adjust the wheel base?
Reply With Quote
  #18  
Old 12-06-2008
ads0021 ads0021 is offline
Member
 
Join Date: Mar 2008
Posts: 90
Default

Oh and is that how you ran it on Sunday at the regional?
Reply With Quote
  #19  
Old 12-06-2008
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

i add washers inbetween the front of the rear hub and the ball joint adam and i tried it in the last final at the regional just to give a little more pivot. tested it again at epr yesterday in the dry and found it to be good with the full set up shown
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #20  
Old 12-06-2008
ads0021 ads0021 is offline
Member
 
Join Date: Mar 2008
Posts: 90
Default

Hi its Adam. I've realized that by doing that you are reducing the hub anti-squat too. I've worked out that by adding 2MM it will make the hub and the wishbone parallel. While also making the wheelbase 2MM longer. I wish i had thought about on Sunday as i think that would have improved my car on the dusty section going onto the straight. You car seemed really stable there and i think this could explain it, do you agree? Will definitely try it next time we're at a track. I think i will also find a way of adjusting the top wishbone as we talked about so that i can change the anti-squat and the wheelbase independently.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com