Setups

[jimmy]

Sticky Thread for posting your SETUPS only.

Please use the other thread in this Losi section for setup discussion to keep this one clear for people to find an appropriate setup !

[Arn0]

Team Losi Setup data base - Electic Off Road
4x2:
Triple X CR
Triple X BK2
Triple X

4x4:
Triple X4
Double X4 & WE

Truck:
Triple XT-CR
Triple XT

Jimmy, if not a appropriate, remove the reply!

jimmy: no mate, thats a cool resource, thank you.

[Cockerill]

Here is my XXXCR setup from last weeks regional at Batley:

Front
Toe - 0
Ride Height – Chassis Level With Rear
Camber - -1
Caster - Std
Sway Bar - None
Oil - 35
Piston - Orange
Spring - Blue
Limiters - None
Spindle Location - Low
Steering Ackerman – Rack
Bump Steer - 0
Camber Link - 2B
Shock Location - 4 Middle
VLA – Long
Front Wing - Yes
Notes - 15gramms in bulkhead

Rear
Toe-In - 3 inboard
Pivot Support - Std
Rear Hub Spacing – Middle
Driveshafts/Outdrives – Steel Dogbones/Steel Outdrives
Ride Height - Driveshafts just below Level
Sway Bar - None
Oil - 35
Piston - Red
Spring - Yellow
Limiters - Inside 0 - Outside 0
Camber Link – 2E 4 gold washers under the ball stud
Shock Location - 2 Middle
VLA - Short
Wing Position - Low
Battery Position - Forward

If you need anything else just ask

[Hulk]

Cheers Tom much appreciated! will give this setup a try at york next saturday.

Craig Collinson

[Swiss]

I have been trying a few differant things on my xxxcr, one is flipping the rear pivot block. Has anyone else tried this? How did they find it?

I am still looking for a nice generic set up, something I will try at Kidderminster on Sunday?

[tyreman]

Originally Posted by Swiss

I have been trying a few differant things on my xxxcr, one is flipping the rear pivot block. Has anyone else tried this? How did they find it?

I am still looking for a nice generic set up, something I will try at Kidderminster on Sunday?

Most of the team have been running that since the prototype car, it helps it go through the bumps better.
Have a look here http://www.helgerracing.com/eknowled...eframeset.html
and go to the losi setup page and try the setups for stotfold.

[bigred5765]

we broke one a couple of weeks ago and found that the xx4 ones fit nps and seem to be same angles etc hole slightly bigger but if your out of the xxxcr ones they worked OK

[Swiss]

Originally Posted by tyreman

Most of the team have been running that since the prototype car, it helps it go through the bumps better.
Have a look here http://www.helgerracing.com/eknowled...eframeset.html
and go to the losi setup page and try the setups for stotfold.

Is that with 25grams of weight in the back as well? Also how does the front shock position relate to the same position using the newxxxcr front shock tower? Did you try that in the wet at Stotfold Brian? How was it?

[RC_NILLE]

Hello I need help whit a start setup for super super high grip carpet track. Whit not soo many jumps. We have to yous Losi Taper Pin for rear and tier trackrion if we whant.

Niclas M from Sweden

[ashleyb4]

May i ask what car you have???????

A

[RC_NILLE]

I have a XXX CR

[ashleyb4]

ant help you with that hadnt any personal exsperiance of it still waiting for mine.

If i remeber correctly Tom Cockerill posted his indoor setup up earlier in the thread have a look though im sure there is a good one there that you can tweak slightly to suit your track.

A

[Arn0]

May that be considered as a valuable replacement of RCsetups?

Triple X-CR

Second post in page 1 give some more pages like this one!

RcNille - You may find what you are looking for with this link.

[magnus]

Does anyone have the setup for the prototype xxx-cr (the hybride) beside doughtys setup that I've already seen?

[DRRC]

Does anyone have a set up for the cactus classic
Thanks

[Arn0]

Originally Posted by DRRC

Does anyone have a set up for the cactus classic
Thanks

Check post#92, there is a setup @ SRS Scottdale

[ashleyb4]

My xx4 starting setup and my xxx-cr starting setup:







A

[lochness42]

I'm searching setups for XX4 and XXX-CR for following conditions:
bumpy track and loose surface (hard clay with layer of dust over it)? Bit rutted after practices of 1:8ths.
Carpets on jumps and also in some corners.
Thank you

[ottoswe]

I've got a good lightweight/lipo setup for basicly the same conditions. The Car weigh just below 1500grams, 10g above minimum

[Dalla]

Hi Ottoswe,
I've just converted to lipo, so I would be very interested in this setup, could you post on here?

Thanks