|
#21
|
||||
|
||||
not bragging
if you read my other post you'll see i was asking questions so i could see what was the best route to send him but OK here goes OK first check the pulley fences are on the right way around then check make sure both pulleys are aligned rite the main reason they twist is pulling the belt over the pulley to get the belt on instead of taking a pulley of also check make sure the belt have no fraid edges as snapped reinforcing material will make them twist also,
__________________
Mattys the driver,my names carl
|
#22
|
|||
|
|||
thanks have just gone through the car again and everything looks good but i do remember when i put the belt on from new it did have some threds showing on the left hand side of the belt so in theory it would flip it to the right so i have found out wot was making it flip will do my best to put some pics up but i am not very good at doing things on the computer as i dont own one do almost every thing on my phone
|
#23
|
|||
|
|||
I am sure the original poster will thank you irrespective of whether or not the information provides useful, but I thank you for restoring my faith in humanity firstly , and the rc community secondly
|
#24
|
|||
|
|||
here are the pics but there is no belt on it as the belt is in half
|
#25
|
||||
|
||||
__________________
Team Schumacher www.racing-cars.com Paint by www.customblitz.co.uk Feedback http://www.oople.com/forums/showthread.php?t=67178 |
#26
|
||||
|
||||
cant see anything overly obvious, pulley fenced are on right although the wires look a little close to were the belts run may be see if you can move em away Little more just encase, if you get a belt that is showing a few threads at the side be very carefully how you do it but i would use the edge of a small screwdriver and coat that edge with super glue very very lightly to seal it up,
__________________
Mattys the driver,my names carl
|
#27
|
||||
|
||||
It's the wires, there's even evidence marks where they are rubbing. Rewire your speedo and reroute the wires, job done.
__________________
___________________________ Neil Adamson |
#28
|
|||
|
|||
Guys.... Pls lets all stop being drama queens.
Even with the pics it is hard to see The belts are not directional Can you pls take a ruler and put it up against tje belt ans see if the thing is straight and look for slight twists Then use the same ruler and see if the pullys alighn up...... If it is scew in any way your spacing is out or the pully is in the wrong place. Can you do that and report back pls Cjeers Levon |
#29
|
||||
|
||||
looks like the belt has been rubbing on the yellow/orange wire to me
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#30
|
|||
|
|||
Looks like you run the wires through the mid belt. Should try to run them under instead also was the mid belt tension right, may want to take out some shims so the bearing can push down the belt further.
|
#31
|
||||
|
||||
Hi mate, hope you get this sorted, I know it was causing you a nightmare on Friday, hard to tell from the pics and without a belt on but it looks like the tensioning pulley is further outboard than the geared pulleys, have you tried sticking a ruler over the top of it to see if they all line up? Could be slipping off the side of the tensioner and flipping it?
__________________
www.worm-racing.co.uk outdoor racing at Weston-Super-Mare
www.yrcc.co.uk indoor racing at Yatton www.southwestrc.co.uk for parts |
#32
|
|||
|
|||
New belt on today and no problems wot so ever happy happy boy againg and 2nd time out and a nice first place in the a final for me :-) must of just bin a doggy belt as the sides where frayed befor I evon stuk it on but all good now thanks for everyone's help
|
|
|