Go Back   oOple.com Forums > Car Talk > Schumacher

Reply
 
Thread Tools Display Modes
  #1  
Old 10-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default KF2 Configuration

With the latest generation of cars like the YZ-2, XB2 and B6 running a lot more mid weight and a lighter rear end than previously. I wondered if anyone had tried a slightly different configuration in their KF2?

Rather than running the low grip set-up, I'm considering moving the motor 20mm further forward, then putting a shorty lipo in the forward position in the space where you'd put saddles? This way you'll get a bit more weight around the mid and take some away from the rear.

Thoughts?
__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West
Reply With Quote
  #2  
Old 11-07-2016
mark christopher's Avatar
mark christopher mark christopher is offline
Spends too long on oOple ...
 
Join Date: Jan 2007
Location: haxey, doncaster
Posts: 7,787
Send a message via MSN to mark christopher
Default

ben jemmo runs kf2 kit motor position, and stubby where saddle is, details on petite rc
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD

Last edited by mark christopher; 11-07-2016 at 04:37 PM.
Reply With Quote
  #3  
Old 11-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default

You got a link? Can't seem to find it!
__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West

Last edited by Danosborne6661; 11-07-2016 at 08:44 AM.
Reply With Quote
  #4  
Old 11-07-2016
mark christopher's Avatar
mark christopher mark christopher is offline
Spends too long on oOple ...
 
Join Date: Jan 2007
Location: haxey, doncaster
Posts: 7,787
Send a message via MSN to mark christopher
Default

http://site.petitrc.com/setup/schuma...n_RHR20150322/
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD
Reply With Quote
  #5  
Old 11-07-2016
bish's Avatar
bish bish is offline
Member
 
Join Date: Dec 2007
Location: Midlands, UK
Posts: 189
Default

Interesting- i wonder what length belt? I can't see any further detail from the pictures.

Edit;
DOH! 117T clear as day...
__________________
Getting back to UK racing.
Schumacher - Tekin - MRT - Futaba
KC
LayDown
BossCat inbound...
Reply With Quote
  #6  
Old 11-07-2016
paulc paulc is offline
Mad Member
 
Join Date: May 2006
Location: Hull
Posts: 1,848
Default

I run the motor in kit position with a shorty lipo but use the Schumacher K2 battery straps so you can have the battery back or forward here's Bens from Petit site

http://site.petitrc.com/setup/schuma...n_RHR20150322/
__________________
Paul Crawford

Trader feedback
http://www.oople.com/forums/showthread.php?t=25152
Reply With Quote
  #7  
Old 12-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default

Quote:
Originally Posted by paulc View Post
I run the motor in kit position with a shorty lipo but use the Schumacher K2 battery straps so you can have the battery back or forward here's Bens from Petit site

http://site.petitrc.com/setup/schuma...n_RHR20150322/
I plan on doing the same Paul rather than the shorty being fixed in place, I'm most inclined to try the shorty in the forward position!

My dad has also been experimenting around with removing plates from the slipper assembly in certain conditions, this could work quite well with this 117t belt set-up if you want more of a 4-gear action in slippy conditions instead of the '3.5-gear' feel.

For those after the 117t, part number is U4494
__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West

Last edited by Danosborne6661; 12-07-2016 at 08:59 AM.
Reply With Quote
  #8  
Old 12-07-2016
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

Even with the low grip layout the weight is a long way forwards, not to say there isn't an advantage to putting the motor all the way forwards if the grip on the track is there. I was thinking of trying motor forwards, but shorty at the back on astro.
Reply With Quote
  #9  
Old 12-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default

I've already been running 40g infront of the motor for the last little while, so makes sense for me to try the motor forward by 20mm.

The latest generation of cars are incredibly light weight on the rear end, but they seem to get round this by mounting the shock much further in on the rear tower so I may try adding a new hole!
__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West
Reply With Quote
  #10  
Old 12-07-2016
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

Putting the rear shocks forwards and running an LCG LiPo are also options for moving the weight forwards.
Reply With Quote
  #11  
Old 13-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default

Ready to test at Mendip RC Raceway tomorrow evening!

Motor moved 20mm further forward as per kit (non low grip conversion), shorty in the forward position, rear shock tower redrilled to move the shocks further in as an option. Just waiting for the 117t belt to arrive tomorrow

__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West
Reply With Quote
  #12  
Old 13-07-2016
mark christopher's Avatar
mark christopher mark christopher is offline
Spends too long on oOple ...
 
Join Date: Jan 2007
Location: haxey, doncaster
Posts: 7,787
Send a message via MSN to mark christopher
Default

http://www.racing-cars.com/pp/New_Ca...KF2/U4403.html


__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD
Reply With Quote
  #13  
Old 13-07-2016
mrspeedy mrspeedy is offline
Senior Member
 
Join Date: Sep 2007
Posts: 974
Default

Quote:
Originally Posted by mark christopher View Post
They're coming with the belt tomorrow
Reply With Quote
  #14  
Old 14-07-2016
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

Looks good Dan, are you going to try LiPo forwards and backwards?
Reply With Quote
  #15  
Old 15-07-2016
Danosborne6661's Avatar
Danosborne6661 Danosborne6661 is offline
Mad Member
 
Join Date: Mar 2007
Posts: 1,301
Default

Quote:
Originally Posted by ianjoyner View Post
Looks good Dan, are you going to try LiPo forwards and backwards?
I just plan on running it in the forward position and adapting the set-up to suit. Last night we tried it at Mendip RC Raceway's bumpy, high-grip astro track and it went great! A few changes were needed to get it there though

Extra hole inwards on the rear tower
We drilled in extra hole inwards on the rear tower, a lot of the 3-gear cars have the shocks a lot more led down so we thought we would try the same. Works good with this new layout and the bumps on the track just vanished!

All slipper pad weights removed except a standard dual set-up
The slipper assembly works great on the low grip layout, but not so much with this new layout! With the extra forward weight AND the large slipper assembly the car was pitching forward too much. We removed all the pads except 2x like on a standard slipper set-up and used a 5mm bearing as a spacer where the spring sits to help pinch up the new set-up. Removing all the pads stops the car pitching around as much and keeps it much more neutral, was skimming over the bumps with ease now!

Shorty weight under lipo
I tried a few different weights under the lipo as well. 35g under the lipo tamed the car down which was nice to drive but a little lively. 70g took too much steering away and caused the rear to lean a little too much. I'll probably end up switching between 35/50g under the lipo depending on what I want the car to do.

+50cst/2.5wt in front shocks
With the weight being that much further forward, the car was diving quite a lot off power and actually causing the rear inside wheel to nearly lift and the geared diff to diff out! I'd suggest if you try this forward layout, you need to add +50cst weight in your front shocks to compensate

Overall though the car was real good, and probably the best my KF2 has felt! I'll be running this same set-up in the wet too, will just need a few tweaks.
__________________
SchumacherPhat Bodies

Mendip R/C Raceway - Offroad Racing in South-West
WORM-Racing - GT12 Racing in the South-West

Last edited by Danosborne6661; 15-07-2016 at 10:54 AM.
Reply With Quote
  #16  
Old 18-07-2016
chrispattinson's Avatar
chrispattinson chrispattinson is offline
Mad Member
 
Join Date: Dec 2005
Location: South Shields
Posts: 1,756
Default

Thanks for the feedback Dan, top stuff.

For the past two years, I've settled on running the KF with kit motor position (and running the shocks on the front of the rear wishbone), but running saddles, with longest wheelbase. The car has a much better balance, and rides the bumps a lot better. We run some fairly bumpy regionals here in the NE, and I've very happy with the way the car glides around the track now.

My thoughts were that the rear of the car was over rotating on power in other configurations, so reducing the weight in the rear of the car, reduced the momentum of the rear of the car rotating.

I played around with moving shocks from the front to the rear, but though I couldn't find a happy medium, I preferred them on the front of the wishbone, and this reduced the over rotation, and gave more steering. Last night I went to small bore rear shocks, mounted on the front of the wishbone, and this was the best it had felt.

Im on 550 front oil black springs, 350 rear oil red springs (small bore).

I also found running the front wishbones on long wheelbase, meant the front wasn't pitching in too much with the weight further forward.

The setup seems to work well on astro, grass, carpet, and multi surface.

I'm going to fit the 117T belt , and try a shorty fwd like yourself, maybe this will be going too far with moving weight fwd, considering my shock position?

I hadn't thought of leaning the rear shocks in further, I might give that a go aswell.

Thanks again for the feedback, Chris.
__________________
Schumacher racing
http://www.racingcars.com ne-rc.blogspot.com
My Trader Feedback : www.oople.com/forums/showthread.php?t=25402
Reply With Quote
  #17  
Old 20-07-2016
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

Thanks for posting Dan.

What rear springs and lower shock position were you running?

What were you thinking for the wet?

Cheers
Reply With Quote
  #18  
Old 20-07-2016
mrspeedy mrspeedy is offline
Senior Member
 
Join Date: Sep 2007
Posts: 974
Default

I'll reply as I've been running this setup with Dan ..

We have been using mostly kit setup all round, so red rear springs on middle wishbone hole, with 3 x 1.7 pistons on 400cst oil ... and seems to work quite well on bumpy high grip astro.

Moving the shocks in on a new hole in the tower loosens the back up in the turns more than kit, doesn't feel so locked in .. takes a while to get used to but seems to work with the lower rear weight bias.

Taking the slipper plates out seems a really good tuning option with this layout too .. stock slipper has quite a forward kick on power ..
Reply With Quote
  #19  
Old 21-07-2016
chrispattinson's Avatar
chrispattinson chrispattinson is offline
Mad Member
 
Join Date: Dec 2005
Location: South Shields
Posts: 1,756
Default

Do you think running motor forward causes a problem of the rear being too locked in though? Just wondering why you are looking to free the back end up with laid down shocks when moving weight forward, I would have thought, and have experienced the opposite to be true .... where moving the weight forward has increased steering, and so no need to free up the rear. But....... consider, my shocks are on the front of the rear wishbone.
__________________
Schumacher racing
http://www.racingcars.com ne-rc.blogspot.com
My Trader Feedback : www.oople.com/forums/showthread.php?t=25402
Reply With Quote
  #20  
Old 21-07-2016
mrspeedy mrspeedy is offline
Senior Member
 
Join Date: Sep 2007
Posts: 974
Default

It's hard to say really. Its a setup we thought up to try and get the KF to work more like the YZ2 and B6/B5m laydown ... they just seem to drive round our track (Mendip) like they're on rails ... and better over the bumps by miles !!

A more central weight gives more natural stability, moving the shocks in on the tower makes the suspension softer and more progressive and adds back in the traction plus steering .. it definitely has a good feel about it ..

All I can say is try it ... its an easy conversion ..
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com