Go Back   oOple.com Forums > General > Vintage RC

Reply
 
Thread Tools Display Modes
  #1  
Old 16-06-2009
tymill's Avatar
tymill tymill is offline
Senior Member
 
Join Date: Mar 2008
Location: London
Posts: 412
Default B4 shocks on a gold tub?

Can it be done? Are the lengths similar? Can I use the original RC10 shafts if need be to get the lengths right? Hmmm..

Love the old gold shocks - but despite rebuilds with new seals and rings they just weep too much and just seem plain tired. Thinking of upgrading...

It's funny - brought my old RC10 out of retirement 2 years ago after about 20 years of storage (I used to race it back in "the day") and it's slowly bit-by-bit becoming another car now that I'm racing it again....

Will never part with the 6-gear though!

Cheers,
Ty
Reply With Quote
  #2  
Old 17-06-2009
Spoolio Spoolio is offline
Mad Member
 
Join Date: Nov 2007
Location: North Notts
Posts: 1,083
Send a message via AIM to Spoolio
Default

Dunno if it can be "done" properly (shaft lengths etc) but I've got some on the back of mine and they seem to work fine. They are just Stealth ones that I had lying about after I'd upgraded to a set of FT threaded shocks on my B4. Far less fafffing about than refilling the ancient old ones.

I had to space the bottom mount out from the arm so I used a longer screw and a brass bushing which was also ex-B4 (steering rack) to get the shock to sit at the correct angle of dangle.
Reply With Quote
  #3  
Old 17-06-2009
superdez superdez is offline
Member
 
Join Date: Dec 2008
Posts: 174
Default

Altough i have never run an RC 10, I do have experiance of the associated shocks as i have just restored a Yokomo Works, and have used associated shocks all round, and after reading numerous posts on RC 10 Talk i am pretty sure you will need the following itmes.

.56 or .71 shocks on the front with the applicable shafts.

1.02 or 1.32 shocks on the rear. the 1.32 will require a spacer inside the shocks, again with applicable shafts.

The rears are available from tower hobbies in the states as whole kits as are the .56.

They use the same internals as modern associated shocks as well as the caps.

You can get the .71 bodies from CML still.

VALKYRIE RC MOTORSPORTS on ebay usually as good second hand/vintage rc 10 stuff

Hope that helps
Reply With Quote
  #4  
Old 22-06-2009
4wdlover 4wdlover is offline
Member
 
Join Date: May 2009
Posts: 16
Default

don't use the b4 shocks on the rc10 they'll cause the rear universals to eat up your outdrives. they're not long enough.

it could be done, but the fronts will be an issue. unless you get a larger front shock tower from ebay or some where else. the rears could be matched with threaded 1.32" shock bodies part# 7415. depending on what you're going to do with your buggy, race or bash you could go with either the 1.02" shaft or the stocker 1.32" shaft. i would recommended the gold 1.02" shaft part# 6417. for the fronts, if you find the shock tower, you could do the threaded 1.02" body part# 7414 with gold 1.02" shafts. or the .71" shafts part# 6418. contact this guy on ebay... kuongkw . he makes shock towers for the rc10 in carbon fibre. his front shock tower allows you to use .89" shocks up front. if you go this route you could get some threaded .89" bodies part# 9312 and the .71" shafts. and your set. i recommended this route because finding a longer shock tower for the front would take you for ever and you'll probably pay a stupid amount for it. wouldn't be worth it. just contact the guy for the front shock tower, and maybe the rear too, and get your 1.32" and .89" shock bodies and you'll be set.
Reply With Quote
  #5  
Old 22-06-2009
tymill's Avatar
tymill tymill is offline
Senior Member
 
Join Date: Mar 2008
Location: London
Posts: 412
Default

Sounds pretty complicated - will do some comparing etc next time I've got the car right next to a B4 and figure out what might be poss.

Thanks for the info though!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
oOple.com