|
#1
|
|||
|
|||
B44: Tight and notchy transmission?
Hi guys,
I’m halfway through my B44 build and while most of it has been very smooth, I’ve noticed that the front and rear transmissions are really tight and notchy. Have checked and ensured they are built correctly, removed flashing from the ring/pinion gear, ensured the gearbox isn't over-tightened. Read on another board that the car should be run like this and that the gears will free up after a few packs. I’m wondering if anyone else has experienced this? Should I run the car as is and expect it to free up? It is one of the tighter transmissions I’ve ever built and it’s certainly not what I expected of this car. Any input would be great! Thanks. BC |
#2
|
||||
|
||||
my one was smooth as anything, an could hardly hear anything it was so quiet.
|
#3
|
||||
|
||||
China moulds....
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#4
|
||||
|
||||
sounds to me like the gearbox isn't shimmed correctly. Play about with the positions of the spacer shims on the diff and see if that helps...
|
#5
|
||||
|
||||
What do the instructions say about shimming?
I looked on the AE site and there is no manual to download G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#6
|
|||
|
|||
Well... the instructions just show the number of shims to put on each side of the ring and pinion gears. I followed them exactly.
I was going to play with the shims but on another board someone mentioned that playing with the shimming would break gears as the gears wore in. Icemike - smooth eh? I guess there might be some tolerance or molding inconsistencies then. |
#7
|
|||
|
|||
Mine was the same, i checked it all through and was fine so ran a few packs through it and its now fine.
__________________
Schumacher |
#8
|
||||
|
||||
i would say there are some inconsistencies for now. i heard about some of the idler gears in the b4 being oval. so im sure that some of the b44 ones will be slightly wrong 2
|
#9
|
||||
|
||||
__________________
Jonathan | Atomic-Carbon |
#10
|
||||
|
||||
I had exactly the same problem but only on one gearbox. I took out one black shim on the pinion shaft and put it together and it was very smooth.
I then read on an American forum that you should not change the kit shims and build it as per instructions and it will bed in. So back in bits again and decided to wet and dry a VERY small amount of flashing which was noticeable from the rear of the pinion. All shims back in and it is smooth now. Not run it yet though! |
#11
|
||||
|
||||
there seems to be alot of "shims" on here lately
|
#12
|
|||
|
|||
Quote:
I havn't checked to see if the B44 uses the same TC3 gears as the BJ4 but if they are the same it's very important you trim the flashing from the back of the pinion gear! |
#13
|
||||
|
||||
Never had to shim the TC3 gears we used in the Pred, and one set has lasted about 5 years in the front (car was run for over 2 years, and is still used as a spare - Used at Worksop last time), and only ever replace once in the rear.
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#14
|
|||
|
|||
The BJ4/B44 have shims in certain positions when you build them, presumably for manufacturing tolerences.
|
#15
|
|||
|
|||
yes the tolerances are off.
has nothing to do with the shimming. shim close or shim far, still is notchy when new. just shim as per manual 4, 3 shims. then run it on a bench for a pack. then run it slowly on the track for another pack. mine is smooth as silk now. the most quiet buggy i have ever driven.
__________________
To Finish First, First you must drive fast |
#16
|
|||
|
|||
Thanks for the input everyone!
Sure helps to know what everyone's experiences are. I did some hunting and even on Associated's site they recommend to run in with the recommended shimming. I'll give that a try. Completed 90% of the car and the rest of the built was very very good. Parts were properly organized by build steps and the quality seemed top notch. Other than the notchy transmission - everything went together well with no fit or finishing issues whatsoever. Read Jimmy's (fantastic) review on the BJ4WE to see the differences that AE has made to the car... many subtle changes, and the slipper certainly looks like a major improvement. Will run in the car once I get the electronics installed and update on the notchy diffs... |
#17
|
||||
|
||||
Do the gearboxes run dry or greased in the B44?
__________________
Nortech is ACE! |
#18
|
||||
|
||||
im running mine dry. the manual didnt say to put any in so i didnt. :P
|
#19
|
|||
|
|||
Manual runs the gearboxes dry... but I put a tad of grease in mine.
Almost done with the car... how are you guys bleeding the shocks? Seems almost impossible to do it as the instructions suggest. |
#20
|
||||
|
||||
mines a notchy as hell so far!!
shocks I just build as I normally build my B4 ones, no problems!
__________________
|
|
|