PDA

View Full Version : steering play on dex210


Loheswaran
17-06-2012, 10:31 PM
I have a dex 210, and am from a TC background.

I am astonished with the amount of play at full lock the car has.

when I have a TC - i just put a washer on the inside of the steering knuckle so that it touches the C-Hub - thereby getting rid of play.

Have any of you tried such an approach, because the play of the inside wheel on full lock must lead to inconsistent handling.

Anyway please let me know your thoughts.

cspurlock
20-07-2012, 05:37 PM
Have u figured anything out on this subject? I too have the same issue.

OneKiwi
21-07-2012, 07:34 AM
I think Jörn did a extra hole in the arm to try and eliminate the inside wheel wobble , not sure if he still runs it. Thats the only mod I have seen done but a washer on the hub may work.

Did you screw it in place or glue it? might pop off if not secured properly with off road

Aran
21-07-2012, 09:02 AM
Got any pictures? Bit confused what you're referring to, are you talking about bump steer?

OneKiwi
21-07-2012, 09:09 AM
http://www.oople.com/rc/photos/offroadwars2012/day1/jorn/OOP_8481.jpg

I thought it was on the other end on the steering hub and not on the steering rack side

OneKiwi
12-09-2012, 07:21 AM
Anyone try something like this at either end?

nicVEGAchildJR
12-09-2012, 09:52 AM
I had the same problem, it was due to the steering rack that I had on my car
The exotek steering rack is lOnger than standard and reduces lock

Loheswaran
05-11-2012, 08:23 PM
I must confess that after the post I have not had a chance to go out racing much. I have seen the Jorn mod, and understand that the new optional rack rids us of the problem.

The simple fact of the matter is that even though the inner wheel carries less load in a corner, the fact that it can shift something like 15 - 20 degrees wholly uncontrolled just seems ludicrous - imagine that in a real car?

discostu
05-11-2012, 08:30 PM
Set your end points correct and your problem will be gone.

av4625
05-11-2012, 08:47 PM
end points wont cure it what new rack?

av4625
05-11-2012, 08:55 PM
i looked on the durango site is the aluminium rack the one u r talking about? is the exotek one not good as i have it ordered?

Darren Boyle
05-11-2012, 09:05 PM
i looked on the durango site is the aluminium rack the one u r talking about? is the exotek one not good as i have it ordered? Over 100 UK racers already own the Exotek rack and not had a single complaint on them as yet other than Nicholas's comment on this thread....

av4625
05-11-2012, 09:32 PM
r they the same size?

discostu
05-11-2012, 10:36 PM
You are clearly doing somthing wrong I can get full lock and the inside wheel holding tight with both the standard rack and the exotech version u an currently running the rdp version again with no problems. And I've even tried it with the older style caster blocks and still full lock.



The steering alteration jorn was using probably had nothing to do with lock but more to do with akerman effect the guy is not stupid he would know full well what effect that location would have on the handling of his 210.

Stu

jo90
06-11-2012, 07:45 AM
I will second Stu here. The wheels both can be made to lock in place at full lock. Take a look at your end point and other steering settings on your transmitter. Make sure they are all set to full and then adjust them back to take any servo strain out of the equation.

Jorn's mod was purely to do with ackerman, not a fault or anything else. Im running the Exotek steering arm to and this is just fine.

AfroP
06-11-2012, 08:48 AM
another shout for the exotek arm here

running that and its fine.

av4625
06-11-2012, 07:02 PM
The steering alteration jorn was using probably had nothing to do with lock but more to do with akerman effect the guy is not stupid he would know full well what effect that location would have on the handling of his 210.

Stu

there is another thread about this and a guy has a video of the problem and i can put my end points full and the wheel wobbles! the only way i can discribe it is like an engine at tdc and the conrod can move back and forth a bit this is the same the arm is pulled to straight its hard to discribe!

I also read a oople report from a EOS round last year and Jimmy did i bit were he focused on jorns car and he said the mod was to pull the wheel tighter to stop the wobble.

So thats y i think jorn done the mod as i read it on a oople repot of a EOS round last year

Not argueing just saying what i saw and my experience with it i have the exotek arm now it came today looks fine!

jo90
07-11-2012, 08:10 AM
Hiya

Mod or not the steering arms will still noly trail as far as the sweep no the steering cranks, so moving the ball joint in on the steering crank makes no difference to tightness of the kunckle against the C-Hub.

Both me and Stu looked at this last night and can't see how your wheel is causing so much play. At full lock the knuckle is held firm against the c-hub.

I would recommend if you can taking photo's of your setup and posting them, it may be something simple is causing this (and being human it can be overlooked easy enough).

Lets see if we can get it sorted for you

dwp102
07-11-2012, 09:06 AM
I had the same problem....it was when I turned the wheels full to the right...found that the steering link was getting stopped on the steering arm...filed some away (about 1mm) and that cured the problem

ekt
07-11-2012, 12:56 PM
Here is a video of the problem several people are having http://i6.photobucket.com/albums/y233/jonski499/2012-10-14_11-34-15_135.mp4

jo90
07-11-2012, 02:29 PM
Can't open it as its MP4 :bored:

jo90
07-11-2012, 02:30 PM
I had the same problem....it was when I turned the wheels full to the right...found that the steering link was getting stopped on the steering arm...filed some away (about 1mm) and that cured the problem

Hmm, I built mine with the Kit link, and the Exotek one and this never occured.

Does anyone have pics of one where they feel this is failing ?

Lonestar
07-11-2012, 02:43 PM
the only way to adjust EPA to cure this is to have the servo force and put the outer wheel suspension under constraint (ie have your EPA "too far"). not good. In stock form and with properly setup EPA's (ie with no static load on servo with wheels turned) it will wobble like crazy. Trigonometrics 101, the 3 points are almost aligned, very easy to move the center one a lot with not much.

My solution to this and other dex210 headaches was to bite the bullet, sell it after running it 4 packs and buy something else.

Paul

av4625
07-11-2012, 05:37 PM
Hiya

Mod or not the steering arms will still noly trail as far as the sweep no the steering cranks, so moving the ball joint in on the steering crank makes no difference to tightness of the kunckle against the C-Hub.

Lets see if we can get it sorted for you

I thought that aswell but just saying wat i saw?

I think i have it fixed for me anyway! i took the 4 screws out the bottom and lifted the whole front end up, i then took the servo horn off and put it on so it was straight down (do this wen the car is on btw), then i ajusted the little turnbuckle thing thats on the servo horn so that wen the horn is straight down the bellcrank/ackerman is in the middle, this seemed to cure it mine was slightly out and was doing the same as the vid not just as bad tho!

I also put the exotek ackerman on and i can confirm that it is exactly the same size and works the same and looks beast!