Team Orion r10 setups

[pizzaman]

Has any one got a good settings starting point using a ballistic 6.5 motor
On 7.4v lipo

[cornishboy176]

2wd/4wd?

I ran a 6.5 in my Centro with punch control on 2 and drag brake on 10% all other settings turned off,it was still too quick and I have now gone down to an 8.5 and it's alot smoother,it also depends on the size of track too

[Crash]

I've been using a setup from one of the Orion drivers to pretty good effect with my 6.5 and R10. My local track does have quite a long straight though and my centro is geared 24/78.

Drag brake 10%
Punch Mode Level 5
Max Brake 75%
Initial Brake drag brake
Neutral range 6%
Boost Timing 10 degrees
Boost Start 5000rpm
Turbo Timing 15 degrees
Slope Rate Fastest
Turbo delay 0.3s

[RudeTony]

Has any one got a good settings starting point using a ballistic 6.5 motor
On 7.4v lipo

What level of racing are you at?

I've been using a setup from one of the Orion drivers to pretty good effect with my 6.5 and R10. My local track does have quite a long straight though and my centro is geared 24/78.

Drag brake 10%
Punch Mode Level 5
Max Brake 75%
Initial Brake drag brake
Neutral range 6%
Boost Timing 10 degrees
Boost Start 5000rpm
Turbo Timing 15 degrees
Slope Rate Fastest
Turbo delay 0.3s


WOW!
Thats a very aggressive set up..you sure you have that right?

[Crash]

WOW!
Thats a very aggressive set up..you sure you have that right?

I hope so Tony - it's what you gave me as a starting point for TORCH!! :lol:

I'll happily take further suggestions though :thumbsup:

[RudeTony]

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

[Crash]

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

Consider me re-educated :lol:
I'll send you an email shortly.

[OneKiwi]

How about setting for in a 410?
Thanks

[gaz1318]

hi what software version are you running 110728 or 111208 cheers

[Jamie B4]

Tony

Can you pm a setup for a 6.5 in a B44.1 as mine does not seem to be that quick

JB

[OneKiwi]

Post it don't PM then we all can learn from it

Gaz were you asking me??? Mine is a 410 V3 6.5/5.5T outdoors then prob a 7.5/8.5 indoors as our track is real tight

[Matt Butcher]

Tony

Can you pm a setup for a 6.5 in a B44.1 as mine does not seem to be that quick

JB

How about this: http://www.petitrc.com/setup/kyosho/setupzx5fs/ZX5FS2SP_2012StartSetup/R10pro_Startingpoint.pdf

[Dudders]

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

What would you do with a 10.5 at SHRCCC Uncle T?

[RudeTony]

Hi Neil

At SHRCC I run an Orion (obviously lol) 7.5 in 2wd with the following settings

Punch = 7
Timing = 6
Turbo = 8
Slope = 12
Delay = 0.3

I belive you have recently extrended the track and I haven't had an oppotunity to race on it yet.....this setting was for your original track.
Punch was turned a little more than normal as wanted the punch between the shorter corners.The turbo was turned down from normal set up as it generated too much and was close to wheelies on the high grip straight.
I did though bring in the turbo earlier to get her going quicker
I hope it all makes sense.......and helps
:)

[Matt Butcher]

As always very helpful tony! :) out of interest which software do you run?

[TARTMAN]

i run a 10.5t aswell. a GM 10.5 with the r10 pro.......

Also about to fit the same to my sx3, so could you, mr tony dude,
give me an idea for both the 2wd 10.5 and the 6.5 HW in the 4x4....;)

[OneKiwi]

Is the team Orion 90A esc going to be ok in a 2wd?