View Full Version : cougar sv steering servo help.
androo
01-09-2012, 03:36 PM
I've just got a cougar sv and i'm going to put my savox sc-1256tg into it.
When the servo is in place I've noticed that the servo horn is very close to the steering centre track rod. is this normal or do i need a low profile servo??
Brewskie
01-09-2012, 04:02 PM
I run the same servo in my cougar an have had no problems at all, just one on the low profile servo, would advise if u do get one not to get savox 1251 as had one myself in the cougar an after 1 month of use stripped the internal gears which was only about 3 race meetings
ian h
01-09-2012, 04:05 PM
I've just got a cougar sv and i'm going to put my savox sc-1256tg into it.
When the servo is in place I've noticed that the servo horn is very close to the steering centre track rod. is this normal or do i need a low profile servo??
You don't need a low profile servo. I run the savox 1258 which is the same as yours for fitting. Is a close fit but perfectly fine.
What servo horn are you running. Standard kit or something else?
androo
01-09-2012, 04:11 PM
thanks for the help. I'm running an answer alu one. I had to grind down the length of the ball stud so it didn't foul the centre linkage and shorten the horn as it was a bit to long. it looks clear, haven't tested it yet but does look close when wheels are straight ahead.
What servo horn do you recommend??
ian h
01-09-2012, 08:50 PM
thanks for the help. I'm running an answer alu one. I had to grind down the length of the ball stud so it didn't foul the centre linkage and shorten the horn as it was a bit to long. it looks clear, haven't tested it yet but does look close when wheels are straight ahead.
What servo horn do you recommend??
I use an answer RC one too. Didn't have to do anything to make it work properly. Used it in my SV and now SV2.
http://www.apexmodels.com/index.php?app=gbu0&ns=prodshow&ref=ANSSHS023-R&sid=94m292t1ah06iz1g785hdm1i9i7m279j
The one in the link is what I have.
androo
02-09-2012, 06:41 PM
thays the one i have, maybe i should have tried it first before shortening the horn, i had to cut down the ball stud though.
tinnylad
03-09-2012, 05:23 PM
Yeah I got the answer alu for my cougar with a savox 1258 and I had to grind the end off it because it was too long. :thumbsdown:
mark christopher
03-09-2012, 07:47 PM
i used a black one from mbmodel and bent it slightly to give good clearance
http://www.rccarshop.co.uk/index.php/rc-accessories/servo-horns/dynamite-1-2-machined-alum-servo-arm-futaba-black.html
ian h
03-09-2012, 08:35 PM
I'll post a pic of mine tomorrow. No grinding, bending or any other mods for that matter, just fits perfectly as it should.
Moss Models
03-09-2012, 08:38 PM
I had the same problem and then purchased a Core one from MB and it fits perfectly.
Muzzie
04-09-2012, 05:17 PM
I use this one no issues
http://www.apexmodels.com/index.php?app=gbu0&ns=prodshow&ref=FAST311B&sid=z53534866q7rk3qs3079ffh998s8832b
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.