PDA

View Full Version : 502X Upgrade set


Aussie Top Force
02-09-2012, 11:11 AM
Found this on Tamiya USA Website:

http://www.tamiyausa.com/product/item.php?product-id=84310 :eh?:

Anybody know what it is or have some images?

taomo
12-09-2012, 05:06 PM
Want images too :drool:

Turd
17-09-2012, 05:37 PM
I have seen the CAD images. The top decks are stiffer, like what Leeroy was testing at Reedy. The rear tower is also 3mm taller and thicker, again, what Lee was already testing.
New inner toe blocks to increase rear toe. They look the same.
The camber mod is a little different. It looks like a Rudebits mod, but all one piece aluminum with no carbon fiber. Four pieces total.

kentech
27-09-2012, 07:42 AM
TRF502X Upgrade...

Aussie Top Force
27-09-2012, 11:21 AM
Thanks Kentech,

I guess the question is whether the set is worth cost? I have the Rudebits camber link set, the sway bar set and aluminium centre shafts. So how much difference will the new upper chassis decks make and the new rear shock tower? There are also the rear suspension lower mount adjustments and the centre shaft universals. Mmmmmmm....:eh?:

I guess it answers that question of 502X or 511X, i.e. which one is TRF developing. Will be interesting to see if TRF brings out anything for the 511 in the future.

Chris
27-09-2012, 08:17 PM
Thanks Kentech,

I guess the question is whether the set is worth cost? I have the Rudebits camber link set, the sway bar set and aluminium centre shafts. So how much difference will the new upper chassis decks make and the new rear shock tower? There are also the rear suspension lower mount adjustments and the centre shaft universals. Mmmmmmm....:eh?:

I guess it answers that question of 502X or 511X, i.e. which one is TRF developing. Will be interesting to see if TRF brings out anything for the 511 in the future.

Please note that the sway bar is 1.4 mm and is not included in the 501x sway bar set.

GRIFF55
27-09-2012, 09:13 PM
I'm pretty sure I have read somewhere that a 511 upgrade kit is out soon.

DavidAMS
27-09-2012, 09:46 PM
Mr Lee Martin seems to be using most of the upgrade kit on his car, going by the photo on the Rudebits site, i think the usefull bits would the shock tower and the rear suspension mounts, they probly would realease just the parts seperate later, i see some of them already on the stella site under the db02 section.

The package price works out pretty cheap for what you get considering tamiya prices, plus its tamiya bling and thats hard to resist...

I want :D

traffman
27-09-2012, 10:22 PM
Ive ordered the kit from Stella , 86 quid all in !

trowta
28-09-2012, 01:12 AM
I have it on now and it looks killer

Chris
28-09-2012, 08:23 AM
I have it on now and it looks killer

pictures?

traffman
28-09-2012, 12:18 PM
I think everyone's ordered one .

The Stella site hasn't any piccies of the kit in stock now!

Aussie Top Force
29-09-2012, 12:07 PM
I just ordered one from Stella. Was still in stock at the time!:)

Mmmm, wonder if Tamiya will respond to the Team Associated's B44.2? Bigs Bores and +8mm chassis? +8mm 511's and 502's?????:eh?:

taomo
02-10-2012, 02:42 PM
I ordered one from Stella too, hope it will arrive soon ^^

traffman
02-10-2012, 03:40 PM
At the end of the day it's all fashion .

I have never an big bores and prob never will unless they come with a future kit.

trowta
03-10-2012, 06:08 AM
well I did I whole bunch of testing and I have to say the upgrade chassis kit and the new steering assembley have transferred this car from a good one to a great one, I was really impressed with the increase in turn in and mid cnr push is non existant now, very impressed, now looking forward to see what the 511 kit will include

mes
03-10-2012, 10:17 AM
At the end of the day it's all fashion .

I have never an big bores and prob never will unless they come with a future kit.

I'd say it depends on your race track. You'll probably not need big bores if your track is smooth. Thanks to some stupid rabbits, our astro track isn't any more, in fact there is a big pot hole in the last third of our straight. My Yoke handles that hole way better with the big bores and lands much smoother when jumping too far, without being overdamped as it would be with heavier shock oil. Big bores FTW! :thumbsup:

Airwave
05-10-2012, 10:05 PM
Got mine today, very interesting set of pieces... But I will have to wait to check the new behavior of the car...

traffman
06-10-2012, 12:18 AM
Just finished building mine , pics up sometime soon.

traffman
07-10-2012, 11:09 AM
My 502.2 is finished but my darling wife has pinched the iphone lead so i will post a pic when she returns from the Airport!

traffman
07-10-2012, 11:58 AM
502.2 x
You get the idea....

http://i64.photobucket.com/albums/h164/traffman/IMG_0896.jpg

Airwave
08-10-2012, 10:03 PM
Quick Galaxy S3 pictures...

There is the trf502x 2012 version:
http://t.imgbox.com/acyr0quK.jpg (http://imgbox.com/acyr0quK) http://t.imgbox.com/adsi9F9u.jpg (http://imgbox.com/adsi9F9u) http://t.imgbox.com/ackkjE9j.jpg (http://imgbox.com/ackkjE9j) http://t.imgbox.com/acbQLMcZ.jpg (http://imgbox.com/acbQLMcZ) http://t.imgbox.com/abzupanu.jpg (http://imgbox.com/abzupanu)

kidcongo
08-10-2012, 11:47 PM
Seems kinda redundant at this point to buy the original 502X kit and then buy the steering upgrade and the chassis upgrade. You end up with a lot of wasted parts. They should at this point just release a TRF 512 and get it over with for anyone who is planning on a purchase. Steering upgrade, chassis upgrade, and maybe some other bling included.

Chris
09-10-2012, 07:52 AM
The new schocktower in the TRF502X upgrade set is a big improvement!

Airwave
09-10-2012, 03:08 PM
why?

Chris
09-10-2012, 03:18 PM
why?

Countersunk holes which gives better acces to the rudebits or tamiya camber link attachment screws. :)

Tweaky
09-10-2012, 04:49 PM
Countersunk holes which gives better acces to the rudebits or tamiya camber link attachment screws. :)

It's also taller, and narrower!
Helps with the droop/driveshaft situation, and gives a bit more on full bounce.

Chris
09-10-2012, 04:54 PM
It's also taller, and narrower!
Helps with the droop/driveshaft situation, and gives a bit more on full bounce.

And gives the possibility to use longer springs, like the tamiya springs ;)

Airwave
11-10-2012, 10:26 AM
Ok thx, nothing I did not think about...

The new swaybar is quite impressive, too...

Chris
11-10-2012, 01:15 PM
Ok thx, nothing I did not think about...

The new swaybar is quite impressive, too...

It's the same swaybar as used on the TRF417 (X).
For carpet racing i use this swaybar (1.4 mm) front and rear. :thumbsup:
It's also available in 1.1mm, 1.2mm, 1.3mm, 1.5 mm and 1.6 mm

DavidAMS
14-10-2012, 05:24 PM
Anyone notice that the rear diff can't be accessed without removing the tower.. ?

Aussie Top Force
15-10-2012, 09:00 AM
Anyone notice that the rear diff can't be accessed without removing the tower.. ?

If you were using the Rudebits camber link, the same problem existed. I prefer the upgrade set option as it is much less 'fiddly'.

taomo
20-10-2012, 07:58 PM
The upgrade set arrived yesterday and I take some photos:
http://i.imgur.com/IQfkO.jpg
http://i.imgur.com/rmn7T.jpg
http://i.imgur.com/xCTEa.jpg
http://i.imgur.com/oQ1zR.jpg

Airwave
22-10-2012, 10:58 PM
If you were using the Rudebits camber link, the same problem existed. I prefer the upgrade set option as it is much less 'fiddly'.

Actually you can, but you have to unscrew half the 4 screws, pull the diff cover, then unscrew totally the 4 screws...

It is totally possible... Diff access was a pain in the as* and it does not improve at all!

traffman
22-10-2012, 11:47 PM
My first outing at Ayr with the new set up was really very good.

Very neutral nice smooth and decent traction .
You certainly feel the stiffer set up , the camber links are less fiddly than the rudebits.

Rudebits links are fine but the bling of the blue just gets an extra vote.

DavidAMS
23-10-2012, 06:17 AM
Actually you can, but you have to unscrew half the 4 screws, pull the diff cover, then unscrew totally the 4 screws...

It is totally possible... Diff access was a pain in the as* and it does not improve at all!

not with the new shock tower..

Arn0
09-11-2012, 04:07 AM
Editable Setup Sheet with 84310 Upgrade Set is now available.
Feel free to provide feedback (preferably by PM or email) if any mistake appears or improvements to suggest.

Airwave
09-11-2012, 04:44 PM
not with the new shock tower..
I do that this weekend... No problem with that.

I begin to unscrew the front screws (about 5 turns, until they are touching the carbon fiber) then unscrew totally the rear screws.

Once done, you can continue unscrewing the front ones, and finally the upper cell comes off...

DaveG28
22-01-2013, 09:01 AM
Guys, with the new rear tower can you run without any limiters in the rear shocks?

Chris
22-01-2013, 10:10 AM
Guys, with the new rear tower can you run without any limiters in the rear shocks?

Depends which hole you run at the whisbone:

inner hole --> 2mm limiter
middle hole --> no limiter
outer hole --> run the old shocktower

Aussie Top Force
03-02-2013, 07:18 AM
Here's my 502X sporting the Upgrade set and quite few other bits from the TRF option bucket!

marco NL
03-02-2013, 12:25 PM
nice :thumbsup::thumbsup::thumbsup:

MITamiya
07-02-2013, 02:26 PM
Looks great Aussie TF.

djmcnz
07-02-2013, 02:59 PM
Here's my 502X sporting the Upgrade set and quite few other bits from the TRF option bucket!

Yep, that's a winner - looks great.

But... are they Tamiya screws I see... :cry: If so I'd replace them ASAP (he says after drilling 14 out of a 501X chassis).

Aussie Top Force
08-02-2013, 02:14 AM
Yep, that's a winner - looks great.

But... are they Tamiya screws I see... :cry: If so I'd replace them ASAP (he says after drilling 14 out of a 501X chassis).

What do recommend as a replacement? And where from?

Chris
08-02-2013, 09:58 AM
Yep, that's a winner - looks great.

But... are they Tamiya screws I see... :cry: If so I'd replace them ASAP (he says after drilling 14 out of a 501X chassis).

Just buy a good wrench (Tamiya 42146). The screws are fine.

BTW: The screws are changed after the release of the TRF501X, all TRF kits from the TRF501X WE have improved quality of screws.

djmcnz
08-02-2013, 10:22 AM
What do recommend as a replacement? And where from?

I use Yeah Racing screws now (http://www.tqrcracing.com/shop/product_list.asp?s_cate_id=1207&s_maker_id=59) but there are many other options.

Edit: I've had good results from these guys in the past as well: http://www.rcscrewz.com/ (502X set (http://www.rcscrewz.com/product_info.php/p/tam142-tamiya-trf-502x-buggy-stainless-steel/products_id/3924))

Just buy a good wrench (Tamiya 42146). The screws are fine.

BTW: The screws are changed after the release of the TRF501X, all TRF kits from the TRF501X WE have improved quality of screws.

I'm not 100% in agreement with this. I agree they are improved but I don't consider them "fine". I have good tools, including hardened ball-end hexs and still find the Tamiya heads too soft. The old dark shiny ones from the 501X are simply terrible, the newer (less shiny, more copper colour) ones are not that much better IMHO. For the sake of 25 bucks I replace them all.

taomo
08-02-2013, 03:58 PM
In my opinion, I consider the screws included in the original 502x kit very soft. I recommend to change them by titanium screws, no doubt :)

Aussie Top Force
08-02-2013, 10:41 PM
Yes, I'm in agreement. I've had to replace both front top shock mounting screws. Both bent and a hex head striped elsewhere.

I'll look into all the options provided thanks!

djmcnz
08-02-2013, 10:52 PM
...and a hex head striped elsewhere...

That's the main problem - especially through carbon or alu into alu.

...I've had to replace both front top shock mounting screws...

If that's the case grab these as well: 54205 - Alu Damper Bushings

They'll help with the upper screws. Use proper 3mm lock nuts instead of the plastic ones as well. Tamiya items are 53022 (silver) or 54155 (blue) but of course you can use any brand.

NB: the bushings are threaded so remove the standard nut and replace it with an spacer!