PDA

View Full Version : TRF511 Chassis Upgrade Set


marco NL
26-09-2012, 06:19 AM
84315 TRF511 Chassis Upgrade Set - should be released in December.

http://kentech.blogs.se/

DeMogoobra
26-09-2012, 09:46 AM
Really looking forward.

Wonder what it will be? It is such a great car already. Hopefully some diffcovers and gear diffs w metal gears. I doubt that though. Going to be very interesting never the less.

stefke
26-09-2012, 12:18 PM
An upgrade set for a car you can't buy anymore ???

Let's hope it's the first indication for a new run of TRF511 kits

AaronR
28-09-2012, 05:47 PM
Longer would be good!

HeavyD99
08-10-2012, 09:03 PM
Came across this info on a (German) Planet RC site - 219 Francs!

http://www.planet-rc.ch/product_info.php/info/p142403_84315-Tamiya-TRF511-Upgrade-Set.html/XTCsid/5c10

New:
Drive Belts
39 Tooth pullies
502x Battery Tray
New Lower chassis - narrower
New Rear lower suspension mounts
New motor mount
New motor bridge
New Diff joints

D.

SimonW
08-10-2012, 09:27 PM
£145 roughly, mmmm

HeavyD99
08-10-2012, 10:51 PM
I just checked that site again, and the price is down to 185 Fr., LOL, hopefully by tomorrow it'll be down to a more reasonable price.

DeMogoobra
09-10-2012, 05:58 AM
Had higher hopes honestly. Like included diffcovers. Those new belts won't do me any good if geardiffs are used. From 38 to 39 tooth pulleys.

Waiting to see how the new Xray car looks.

kentech
09-10-2012, 06:51 AM
Had higher hopes honestly. Like included diffcovers. Those new belts won't do me any good if geardiffs are used. From 38 to 39 tooth pulleys.

Waiting to see how the new Xray car looks.

There is already a 39T gear diff pulley/case available:

51463 TA06 Fnt Gear Diff Pulley - & Case Set 39T
http://www.tamiyausa.com/product/item.php?product-id=51463

DeMogoobra
09-10-2012, 06:52 AM
Ha ha, my heart just went back to normal pace ;)

Chris
09-10-2012, 07:55 AM
Nice!

http://www.planet-rc.ch/images/product_images/popup_images/10_84315.jpg?XTCsid=1e1e25247319f16fdc940132dff79d 99

Fredrik Emilsson
09-10-2012, 08:05 AM
Yes, swapped drive belts=motor further in etc.

Nice upgrade!:)

rcyogi1
09-10-2012, 03:27 PM
Hello!

Can I use this set for my 501x also?

regards
Tom

olefiloux
09-10-2012, 04:42 PM
Yes, swapped drive belts=motor further in etc.

Nice upgrade!:)

Further forward, or further back?? what will it change exactly!??

James
09-10-2012, 04:47 PM
The belts on the spur pulley are swapped so in theory the motor could be moved further inboard, would make the car a little more 'reactive' I'd suggest, but not much.

Chris
09-10-2012, 04:52 PM
Hello!

Can I use this set for my 501x also?

regards
Tom

no you can not

HeavyD99
09-10-2012, 04:53 PM
I just received my dust covers (& lipo tray) from Fredrik and with this f/r belt swap they will not fit! Some really nice bits, top level racers will get the most out of it I'm sure, but for me at the club level, I like my "old" 511 the way it is now.

olefiloux
09-10-2012, 05:01 PM
Thanks James.
so the motor in more in the axle of the car... great.
Fredrick.... please, let's do some new parts:lol:

rcaddict
09-10-2012, 07:35 PM
So Fredrik's new gear diff covers wont work with this new upgrade set??

DaveG28
09-10-2012, 11:44 PM
Hmmm, not sure this is enough to tempt me back out of the 502....especially as there is still no word of any re-release of the 511 itself! I just wish the 502 had gear diff's....

HeavyD99
10-10-2012, 12:15 AM
Hmmm, not sure this is enough to tempt me back out of the 502....especially as there is still no word of any re-release of the 511 itself! I just wish the 502 had gear diff's....

Why not build your own gear diffs? A mix of Durango and one or two ther manufacturers and you've got gear diffs.

Airwave
11-10-2012, 10:25 AM
Very complicated! Durango are too big, you will have to sand your plastic parts! and change dogbones too!

I quite like the balls diffs... But I do replace the Tamiya "thrustbearing" by a real one and now it is butter smooth...

90% of the time you have a crunchy diff, it comes from this part...

Tweaky
11-10-2012, 12:01 PM
Hi Airwave

What do you replace them with?, as i'm at the point of no return with my ball diffs in the 502.

Cheers

I quite like the balls diffs... But I do replace the Tamiya "thrustbearing" by a real one and now it is butter smooth...

90% of the time you have a crunchy diff, it comes from this part...

Fredrik Emilsson
19-10-2012, 09:45 AM
TRF511 now discontinued on tamiyausa.com

Could indicate that new version will be released, probably with the upgrade kit.
Like TRF201 with upgrade set.

DeMogoobra
19-10-2012, 10:38 AM
Ohhh, me like :)

David Church
19-10-2012, 10:49 AM
TRF511 now discontinued on tamiyausa.com

Could indicate that new version will be released, probably with the upgrade kit.
Like TRF201 with upgrade set.


I do hope they release a new car!!!!

super__dan
20-10-2012, 09:01 PM
Hi Airwave

What do you replace them with?, as i'm at the point of no return with my ball diffs in the 502.

Cheers



I'm interested in this too?

DaveG28
20-10-2012, 09:50 PM
I'm interested in this too?

Do the old style pre built thrust races still fit? I never had a problem with them?

I have the same 502 issues are others here, to avoid diff slip they end up tighter than I want them, and then gravelly very quickly!

Rich D
20-10-2012, 10:07 PM
Do the old style pre built thrust races still fit? I never had a problem with them?

I have the same 502 issues are others here, to avoid diff slip they end up tighter than I want them, and then gravelly very quickly!


I found the same Dave regarding the slip. I superglue the plates to the outdrives now and havent looked back. Next time you rebuild your diffs, look at the wear on the outdrives where the plates have been slipping ! Theres a flat machined on the outdrives but for some reason no flat on the diff ring which would cure the problem without the need for the glue. Try it.

Origineelreclamebord
21-10-2012, 06:26 AM
I found the same Dave regarding the slip. I superglue the plates to the outdrives now and havent looked back. Next time you rebuild your diffs, look at the wear on the outdrives where the plates have been slipping ! Theres a flat machined on the outdrives but for some reason no flat on the diff ring which would cure the problem without the need for the glue. Try it.

I don't glue them, I use Tamiya AW grease: It's extremely sticky and thick, so it's so slow reacting that it won't slip (and it's more easily removeable than glue). That said, I like the ball diffs as well, but mine did get quite grainy. I cleaned everything but it was still grainy, so I think the thrust bearing is up next to replace (even though I used ceramic thrust bearing balls it's probably past the best life). I nowadays use a gear diff (in my 201) though, which also works well so far, so I feel no need to rush :)

Rich D
21-10-2012, 01:04 PM
I don't glue them, I use Tamiya AW grease: It's extremely sticky and thick, so it's so slow reacting that it won't slip (and it's more easily removeable than glue). That said, I like the ball diffs as well, but mine did get quite grainy. I cleaned everything but it was still grainy, so I think the thrust bearing is up next to replace (even though I used ceramic thrust bearing balls it's probably past the best life). I nowadays use a gear diff (in my 201) though, which also works well so far, so I feel no need to rush :)


Yeah i have tried the AW grease and the VG diff plate grease. The hard friction damper grease too. Its stickier than the AW stuff. Definitely better than diff lube on the backs of the plates, i found that they still slip on high grip surfaces though. I have a spare diff so i can leave the glued one soaking in Acetone overnight to remove the plates once in a while. It all depends what surfaces you race on as to whether you need to bother to glue them IMO.

Airwave
22-10-2012, 10:55 PM
I do confess guys, the real challenge was to find a thrustbearing which can fit the 2.6mm screw... Tamiya only sells 2mm...

So I look on the web, and after days of search (:D), I finally manage to found a compatible one....

http://www.redrc.net/2011/01/t-o-p-photon-thrust-bearing-sabre-fd-gear-diff/

Then I found a shop carrying TOP parts and ordered them... A really great improvement for me, I'm quite disabled when it comes to build a godd smoothy differential...

Hope this helps!

DavidAMS
23-10-2012, 06:56 PM
i found the thrust bearing airwave is on about, http://www.raceport.de/TOP%20Racing%20DE/product_info.php?products_id=1120

only 5 euro, worth a try.

HeavyD99
23-10-2012, 08:55 PM
...or use the 417/201 thrust kit. It's not the same 'captured' ring style, but you can upgrade to ceramic thrust balls - or simply buy a complete B-fast thrust kit, available in carbide or ceramic.

Airwave
27-10-2012, 12:50 PM
My point is that captive balls are the key... The fact is that when the diff run at high speed, the balls are "ejected" by the centripetal force and roll on the inside face of the diff joints, and I'm not sure the inner surface is as polished as the pressure plates... My theory is that produces the "crunch effect" so fast!

Bu that's only my theory... :blush:

msxmre
27-10-2012, 01:56 PM
Airwave that's what I've always thought, just never been able to put it as nicely into words. Top job m8,
Scotty....

msxmre
27-10-2012, 01:57 PM
I bought buds balls ceramics for my TRF502 and never had any problems so far.
Scotty....

qatmix
27-10-2012, 02:23 PM
On my Touring car (TRF) I used ball diffs and ceramics (same on my 501x) and they probably get serviced twice a year.

I would used ceramic balls on the non captive Thrust bearings. I also use Tamiya AW grease on these. Its seems to keep the thrust bearing smooth for ages.

HeavyD99
27-10-2012, 02:44 PM
My point is that captive balls are the key... The fact is that when the diff run at high speed, the balls are "ejected" by the centripetal force and roll on the inside face of the diff joints, and I'm not sure the inner surface is as polished as the pressure plates... My theory is that produces the "crunch effect" so fast!

Bu that's only my theory... :blush:

Well, it's an interesting theory, and makes a lot of sense, but I've never had the issue of thrust balls being ejected or running on the inside of the diff joint - most often when I check the rings, they have worn in the middle - not to the outside of the ring.

If it works for TC's running 4.0 motors, it'll work in a slipping and sliding off road buggy running 6.5's.

Fredrik Emilsson
06-11-2012, 09:24 AM
This parts set is designed for the TRF511 Chassis and includes a wide range of race-spec Option Parts to further improve its performance potential. The new carbon lower deck and aluminum rear suspension mounts enable the chassis to be compatible with square-shaped battery packs. The new aluminum motor mount shifts the motor position towards the center of the chassis. In addition, the use of 39T pulleys results in an optimum secondary gear reduction ratio.


Set Contents
2.25mm Carbon Fiber Lower Deck (new)
Aluminum Rear Suspension Mounts (new)
Aluminum Slide Motor Mount (new)
Aluminum Center Bulkhead Bridge (new)
Diff Joints (Front & Rear) (new)
Drive Belts (Front & Rear) (new)
TRF502X J parts (battery holder)
39T Ball Diff Pulley (Front and Rear)
TRF417 Diff Plates (Front and Rear)

HeavyD99
06-11-2012, 05:27 PM
I had gear diffs in my DB01R, and they leaked out in one race night - made a mess of the cases and belts. Pulled them out, rebuilt them using some green slime, and same thing. They leaked out around the outdrive, not at the case halves, so the gasket was not the issue, it was the o-ring and the three spacers which were not doing their job. I wanted to run gear diffs so badly as well. I have not tried a thicker/wider spacer yet, that might solve the issue - but a well built ball diff still seems to be the way to go.

Lee Martin
06-11-2012, 07:15 PM
If it works for TC's running 4.0 motors, it'll work in a slipping and sliding off road buggy running 6.5's.

I wouldnt be so sure... off road cars have a lot more force running through the diffs than the fastest touring car.

Same with anything off road to on road... a F1 gear box would not last 5 minutes banging around in a rally car for example. Dont under estimate the strain the off road diff goes through.

:drool:

HeavyD99
07-11-2012, 04:25 AM
So put this debate to rest Lee - whaddya use in your diff, the 'captured' thrust bearing kit or separate diff balls and diff rings?

kentech
08-11-2012, 01:51 PM
http://kentech.blogs.se/

http://data8.blog.de/media/160/6717160_76366cd0ba_o.jpg

DeMogoobra
08-11-2012, 03:55 PM
Does not seem like there will be another realise of 511 though?

James
08-11-2012, 04:16 PM
I love this quote from the description:

"We will release a set of upgrade parts to further enhance the combat power of ITEM42139 TRF511 Chassis Kit."

Chris
08-11-2012, 05:40 PM
I mounted the 39T pulleys today, they fit perfectly without contact the gear covers. :)

Fabs
21-11-2012, 05:03 PM
The TRF417 diff rings that are to be used with the new ball diffs do have the D cutout that will lock up with the outdrives...

HeavyD99
19-12-2012, 02:47 AM
Aluminum Slide Motor Mount (new)
Aluminum Center Bulkhead Bridge (new)
Drive Belts (Front & Rear) (new)
39T Ball Diff Pulley (Front and Rear)

Anyone know if these bits can be purchased separately?

clint
19-12-2012, 04:09 AM
Hey Daragh, Gordie got the 511 upgrade kit from Tom, looks like a sweet kit!!

Chris
19-12-2012, 10:21 AM
Hey Daragh, Gordie got the 511 upgrade kit from Tom, looks like a sweet kit!!

Pictures?

djmcnz
19-12-2012, 11:26 AM
Ordered.

I think €108 + shipping is not a bad deal. Should have it for the new year, can't expect speedy shipping at this time.

Anybody know if I will be able to re-purpose any of the original 511 bits I end up with to a 501X for any benefit?

James
19-12-2012, 01:05 PM
Where was this ordered from please?

djmcnz
19-12-2012, 02:12 PM
Here you go:

http://www.tamiya-asia.com/shop/tamiya/84315/110/rc/trf511/upgrade/set-p-90058644.html

AaronR
28-12-2012, 06:44 PM
Just noticed stella models shows them on their eBay store.

t8rtot
29-12-2012, 05:19 PM
Any idea if Tamiya will re-release the 511 or an updated car (Worlds Edition)?

djmcnz
03-01-2013, 01:35 PM
Yay! Weekend project... :)

http://dl.dropbox.com/u/10492238/IMG_20130103_132726.jpg

Edit: WTF Tamiya?

The upgrade kit requires you to trim 3 x plastic parts from the stock kit (B2, B8 and A1 if you're still using plastic steering). It would have been relatively simple to re-mould these and include them in the upgrade.

But worse the instructions call for you to "Cut of any sections on BD20 [from the stock kit] that come in direct contact with the ball differential" great but BD20 is an aluminium part!! It's the front suspension mount. :-| What are we meant to do, take a grinder to it???

trf14
21-03-2013, 08:43 PM
Anybody a good set up for dirt with the upgrade trf511
Thx

rcaddict
30-06-2013, 03:42 AM
Can I use my old Fredrik diff covers, or do I have to buy new ones now with this upgrade set? :confused:

James
30-06-2013, 07:40 AM
If you use the old pulleys you might be ok, I assume you can use the gear diffs with the new belts - just simply turn the eccentric housings round further to keep them tight enough - anyone?

djmcnz
30-06-2013, 03:03 PM
Be careful if you use any diff cover with any 39t pulley in these, I ruined two pulleys and a belt doing so. There's insufficient clearance within the bulkhead assembly to allow anything to pass through causing everything to bind if even a tiny stone gets in (which it will if there are any at all on your track). I posted about it on here somewhere.

HeavyD99
30-06-2013, 08:13 PM
Can I use my old Fredrik diff covers, or do I have to buy new ones now with this upgrade set? :confused:

The old diff covers will not work - you'll need Fredrik's new "upgrade kit" diff covers, 1) because the pulleys are larger and 2) the diff/belt is now running/coming out "on the other side". They are already available - see Fredrik's thread.

@trf14, As for set ups, the suspension set up is basically the same for the old 511 vs. the upgrade kit - go to petitrc.com and look for set ups there.

Fredrik Emilsson
02-07-2013, 09:44 AM
Would say, be careful to run with 511 at all on tracks with small stones.
I have ruined several pulleys and belts running without covers.
They get stuck between pulley and rear suspension mount.

Short diff covers give some protection, but as I have said before, not sufficient protection on those kind of tracks.

You will need long diff covers to get proper protection on tracks with small stones.

Might do a revised long diff cover for conversion set.

djmcnz
02-07-2013, 10:13 AM
I'd be interested in the long ones again.

My track hasn't changed in 4 years so the stones were always there (very, very small 2mm - 3mm stones).

Never had a problem with your long diff cover, it was awesome.

As soon as I got the upgrade kit and used short covers disaster struck (combination of smaller cover and bigger pulley).

Running without covers now with no immediate issues (because the stones seem to get spit right out again if they're 'ingested') but the the peace of mind would be good because something will eventually get jammed.

rcaddict
02-07-2013, 03:10 PM
Hey Fred!
I'm in for some revised long diff covers too. :D

Keep us updated! :thumbsup:

Fabs
24-09-2013, 09:48 PM
My TRF511 with upgrade set is for sale

http://www.oople.com/forums/showthread.php?t=136610

AaronR
02-02-2014, 01:11 PM
....

rcaddict
10-02-2014, 07:57 PM
Looks like Fabs is getting ready for a 503. ;)