PDA

View Full Version : superstox advise


tisher
13-10-2012, 09:22 AM
just run my superstox last night built to the book running 13.5 on a blinky setting the car was near impossible to drive it was awful. It veered of every time you tried to put any power down it was really snappy into every corner.

In rd2 I moved the rear springs to the outside setting buried even more additive on the back car still kicked all over the place like a bad set up dave but was slightly better.

So rd3 I put some toe in on the front turned down my throttle curve to -100% and turned my steering epa down to 50 :woot: it was better then but still a lap off the pace.

At the moment I am a bit disheartened with it and thinking of going back to the dave as it would have been quicker with its stock g12 than this.

So has anyone got any tips on stopping the back end from kicking all over when putting any sort of power down and stop it being so snappy on the corners all advise would be great cheers:)

neallewis
13-10-2012, 09:45 AM
Throw away the kit front tyres. Use 60 or 50 shore tyres. Check your ride height, set it for 4mm. I've gone harder on the front springs, and am going to try a harder rear spring tonight. Use the middle holes on rear pod. I initially ran without Orings in the links, but run them now.

CAT3K
13-10-2012, 10:00 AM
The kit fronts are very grippy, i changed mine for 50's. I also changed my servo position to as far back as i could get it to make it less snappy. The steering on my radio is only set to 70% as well.

Are you running the diff or not? With diff mine is a dream to drive, without i have to run the softest O rings under the links, i didn't like it with no O ring at all.

I can say honestly say that mine was as quick out of the box (with diff) as a well set up dave.

mark christopher
13-10-2012, 10:24 AM
i run kit tyres all round with no issues

two things to check, double chech the link length of the turnbuckle infront of motor pod, this must be correct to the book, and what gear ratio are you running, i run 30/70 on a small track as the rear stepped out on power if a low gear ratio was used, not the only on to find this

neallewis
13-10-2012, 10:45 AM
double chech the link length of the turnbuckle infront of motor pod, this must be correct to the book,

yes this is important! I forgot that one.
Even with that critical adjustment set right, mine did used to pull sometimes on acceleration depending on carpet and direction of the pile. That went away when I got the diff.

stegger
13-10-2012, 12:04 PM
i run kit tyres all round with no issues

two things to check, double chech the link length of the turnbuckle infront of motor pod, this must be correct to the book, and what gear ratio are you running, i run 30/70 on a small track as the rear stepped out on power if a low gear ratio was used, not the only on to find this

What dia tyres Mark, blinky mode, motor ?

mark christopher
13-10-2012, 01:40 PM
47/35 shore, 47.5/50mm thunderpower motor 25 deg timing blinky speedo (hobbywing 1s) 30/70 pin/spur

tisher
13-10-2012, 02:31 PM
so are all you guys running a diff then I know this would no doubt calm the back end down as you could set a bit of slip
I was running the kit spur and 16 pinion last night
cheers for all the advise so far guys I really want this car to work for me as I enjoy running mardave class the most for my friday fun nights

stegger
13-10-2012, 03:14 PM
47/35 shore, 47.5/50mm thunderpower motor 25 deg timing blinky speedo (hobbywing 1s) 30/70 pin/spur

Cheers Mark. Might be a daft question this but can a certain speedo be better than another speedo on blinky mode ?

mark christopher
13-10-2012, 03:59 PM
Cheers Mark. Might be a daft question this but can a certain speedo be better than another speedo on blinky mode ?
suposedly no, but im sure there will br slight differences in punch etc

reg
13-10-2012, 07:59 PM
mine was the same,untill i fitted the diff,total changed the car,its ace to drive now:thumbsup:

PaulUpton
13-10-2012, 08:22 PM
Cheers Mark. Might be a daft question this but can a certain speedo be better than another speedo on blinky mode ?

From what I've heard the hobbywing speedo has a certain amount of static timing built into it even in blinky mode. There is a noticeable difference when I've races against people using hobbywing vs my core pacer

stegger
13-10-2012, 11:34 PM
From what I've heard the hobbywing speedo has a certain amount of static timing built into it even in blinky mode. There is a noticeable difference when I've races against people using hobbywing vs my core pacer
Interesting , so the only real way of having a "STOCK SETTING" would be for all manufacturers to run the same software or components and that wouldn't happen ! Not really a equal playing field !

It would be good to see what people were using today to see if there was an advantage.

Chequered Flag Racing
14-10-2012, 06:21 AM
Join in here @ GT12 Circuit Cars UK (https://www.facebook.com/groups/336445139755237/) and join a 200 strong community ;)

PaulUpton
14-10-2012, 03:51 PM
You cab also do something with a lrp speedo it give it timing in blinky mode

sosidge
14-10-2012, 08:14 PM
You cab also do something with a lrp speedo it give it timing in blinky mode

So what you are saying is that the people at ROAR who are putting all these ESCs on an oscilloscope to check that they are built to the exact blinky specification are doing it wrong and that a significant proportion of the ESCs allow you to cheat?

In that case could you explain why my "cheat" Hobbywing Xtreme Stock ESC is exactly the same speed as my (hopefully legal) Speed Passion Reventon ESC? And can you explain why LRP (who happened to have helped create the Blinky spec) are still submitting cheat speedos? And can you explain why the A-final cars at the Cotswold BRCA Clubman's national on a 60m straight were incredibly even on pace, with a variety of ESCs in use?

The problem with Blinky is that everyone is paranoid about getting beaten, And if people get beaten, they suspect foul play. The truth is, some people are better at preparing their powertrain, some people are better drivers, and some people are both.

PaulUpton
14-10-2012, 08:34 PM
Ummm cheating, don't think I mentioned that. You think your speedo is cheating, maybe what I heard is correct. :lol:

Just saying what I have been told. The LRP 'trick' is a sequence of some sort you do to change settings on it. Obviously only LRP insiders would know this, unless its not true and just a romour.

Not worried about being beaten, infact the 4 GT12 meetings I've done I've TQ'ed and won all 4, even beaten your "cheat" speedos :woot: all about corner speed with GT12 ;)

Not sure how they check speedos, but would the way they check them only check timing advance or will it do static timing. As that's what I have heard the hobby wing has over the core one

From MY experience the hobby wing speedos I've ran against have had higher top end than my core with roughly the same rollout/lipo ratings.

Chequered Flag Racing
14-10-2012, 08:48 PM
mine was the same,untill i fitted the diff,total changed the car,its ace to drive now:thumbsup:

I had the diff fitted and the car was sh*te. Changed the rears which were kit 32's to another set of 32's and it was sorted. So can only have been the tyres. Now have the V12VRXce though :D

Motor and gearing go for around 68/70mmpr. I went to Barley Mow and checked in with Mark Jewitt re rollout for a smaller track and he said just leave as is. He was right.

Martyn (Bomber)
14-10-2012, 09:40 PM
Not worried about being beaten, infact the 4 GT12 meetings I've done I've TQ'ed and won all 4

Are these club meetings ???

PaulUpton
15-10-2012, 01:18 AM
Are these club meetings ???

Yep, they were in deed. HRCC, Bedford and MK but beating people who were in the A final at the national over weekend. ;)

Even made A finals at touring car meetings with it too

Anyway this thread was someone asking for advice, not about cheaty speedos and me :blush: let's keep on track.

mark christopher
15-10-2012, 08:21 AM
So what you are saying is that the people at ROAR who are putting all these ESCs on an oscilloscope to check that they are built to the exact blinky specification are doing it wrong and that a significant proportion of the ESCs allow you to cheat?

In that case could you explain why my "cheat" Hobbywing Xtreme Stock ESC is exactly the same speed as my (hopefully legal) Speed Passion Reventon ESC? And can you explain why LRP (who happened to have helped create the Blinky spec) are still submitting cheat speedos? And can you explain why the A-final cars at the Cotswold BRCA Clubman's national on a 60m straight were incredibly even on pace, with a variety of ESCs in use?

The problem with Blinky is that everyone is paranoid about getting beaten, And if people get beaten, they suspect foul play. The truth is, some people are better at preparing their powertrain, some people are better drivers, and some people are both.
you culd be thinking of static speedo timing/punch and not on the fly timing

russmini
15-10-2012, 10:49 AM
Well, I can't fault it. I run a setup very close to kit, even Saturday at Tamworth running kit front springs and foams. Rear springs kit and in middle position.
Always run 37's on the rear.
TQ'd racing on Saturday and the car was awesome.

I would add I've had a few weeks of soso results whilst testing different front end setups. After starting to slowly going backwards to kit, each change resulted in me being quicker. So for me, from now on kit/what I said above is where I'll always run mine now.

SlowOne
15-10-2012, 04:10 PM
so are all you guys running a diff then I know this would no doubt calm the back end down as you could set a bit of slipNever run a ball diff with slip in it. It will flat the balls or the rings or both, and then as a diff it is not much better than a solid axle from a handling perspective. If you can't make the car handle unless it has less power (which is all a slipping diff is doing) then sort the car out.

From what I've heard the hobbywing speedo has a certain amount of static timing built into it even in blinky mode. There is a noticeable difference when I've races against people using hobbywing vs my core pacerComplete rubbish. See the BRCA 12th Rules for the correct definition of a blinky speedo. This is the definition used by ROAR and is what their lab uses to check a speedo. It is the definition being worked by the BRCA for their use.

Interesting , so the only real way of having a "STOCK SETTING" would be for all manufacturers to run the same software or components and that wouldn't happen ! Not really a equal playing field !

It would be good to see what people were using today to see if there was an advantage.Correct, and for all motors to be run with the sensors at the same angle to the stacks. That's why there is a speedo that people reckon is just a smidge better than the rest...

You cab also do something with a lrp speedo it give it timing in blinky modeNo you can't... period. Maybe the factory could, but you can't. And the factory never would since if they were caught cheating their reputation would be rubbished and their products banned by all the National Associations. If there is one guy passionate about sticking to the Rules it is Jurgen Lautenbach.

So what you are saying is that the people at ROAR who are putting all these ESCs on an oscilloscope to check that they are built to the exact blinky specification are doing it wrong and that a significant proportion of the ESCs allow you to cheat?

In that case could you explain why my "cheat" Hobbywing Xtreme Stock ESC is exactly the same speed as my (hopefully legal) Speed Passion Reventon ESC? And can you explain why LRP (who happened to have helped create the Blinky spec) are still submitting cheat speedos? And can you explain why the A-final cars at the Cotswold BRCA Clubman's national on a 60m straight were incredibly even on pace, with a variety of ESCs in use?

The problem with Blinky is that everyone is paranoid about getting beaten, And if people get beaten, they suspect foul play. The truth is, some people are better at preparing their powertrain, some people are better drivers, and some people are both.Now there's a guy who knows the facts, and what he is talking about!

Just saying what I have been told. The LRP 'trick' is a sequence of some sort you do to change settings on it. Obviously only LRP insiders would know this, unless its not true and just a romour.

Not worried about being beaten, infact the 4 GT12 meetings I've done I've TQ'ed and won all 4, even beaten your "cheat" speedos :woot: all about corner speed with GT12 ;)

Not sure how they check speedos, but would the way they check them only check timing advance or will it do static timing. As that's what I have heard the hobby wing has over the core one

From MY experience the hobby wing speedos I've ran against have had higher top end than my core with roughly the same rollout/lipo ratings.It's just a rumour... they check them electronically and examine their software and then they confirm the blinky mode signal... and you have found the speedo that has a smidge more, but only in one variety... ;)

But let's get back to helping out with the Supastox... :thumbsup:

tisher
16-10-2012, 07:51 AM
Never run a ball diff with slip in it. It will flat the balls or the rings or both, and then as a diff it is not much better than a solid axle from a handling perspective. If you can't make the car handle unless it has less power (which is all a slipping diff is doing) then sort the car out

But let's get back to helping out with the Supastox... :thumbsup:


Hence why I am asking for some advise :)on friday I could not even get the car off the line with any more than quarter throttle it just veered off to the left soon as any sort of power was put down I am going to try some of the above advise for this friday to see if I can calm it down

russmini
16-10-2012, 10:43 AM
What prep do you do before you get to the line? Can you have an installation lap or 2 etc? I have always found that for at least half a lap, the back end is very loose, but by the time I've done an installation lap, the car is sorted. I also usually never apply full throttle off the line, I always build it up. For the final on Saturday, I managed to do 3 or 4 practice starts, gunning the throttle each time. I had TQ'd, so wanted to get the hell out of there. It worked perfectly.
Perhaps that's something you could try?

tisher
16-10-2012, 01:33 PM
What prep do you do before you get to the line? Can you have an installation lap or 2 etc? I have always found that for at least half a lap, the back end is very loose, but by the time I've done an installation lap, the car is sorted. I also usually never apply full throttle off the line, I always build it up. For the final on Saturday, I managed to do 3 or 4 practice starts, gunning the throttle each time. I had TQ'd, so wanted to get the hell out of there. It worked perfectly.
Perhaps that's something you could try?


yea get a few laps to warm up the tyres etc the car just felt like it had way to much torque I have managed to get hold of a diff so going to put that in but I am new to brushless 12ths I did one series with a g12 mardave that ran really well but this thing was just a nightmare :woot:

SlowOne
16-10-2012, 02:10 PM
I hope this helps some of you, even though it is not the only cause of Tisher's problem IMHO...

You should not have to run any installation laps to bed the tyres down. Installation laps are to test grip and set steering throw based on what you feel the car is doing, and to confirm what the grip level now is.

When applying additive to foam tyres for carpet, rears are usually done for twice the time of fronts. Ideally, using CS High or Speedtech, rears should be done for 20 minutes, and fronts for 10 minutes. Rears should be full width additive, and fronts half width. Apply sparingly with a soft-haired brush. Soaking them just makes them soft and wastes additive.

Remove all the excess additive with a towel, and then rub the tyres until they are 'dry' to the touch. Take care not to spread that additive across the whole front tyre when doing this. Now make a final dry using a piece of he towel that has no additive on it. All this should be complete the heat before you run so the tyres are completely dry and ready to race.

On a club night there often isn't time for that procedure, so try using only two sets of tyres and alternate them from side to side, and heat to heat. After their first application of additive, cut the time the additive sits on them in half, but still make sure they are rubbed dry. Wherever possible, let them sit in that state for a heat before you race.

If you can't let them sit, then rub harder to make them dryer. Drive the first few corners of your installation lap slowly, then do a couple of standing starts to dry off the rears completely. If possible, make the car understeer on a couple of corners to dry off the fronts. Now you are ready to race.

The object of the exercise is to have dry tyres at the start of the race. That will give you the most consistent handling throughout the race. If you start on wet tyres the car will be everywhere, you will lose loads of time, and then during the race the handling will change. That's not a good basis for changing set-ups to gain lap time!

I do see drivers coming from TC put cars down with wet tyres - not good! Also, just because the tyres dry when you race them does not mean they are 'stable' for a whole race. On high-grip tracks, wet tyres will react differently with the additive already on the carpet, and that will again make the handling change through the race. Dry tyres are the key to a good race time. HTH :)

joker
16-10-2012, 03:09 PM
dose it do this just of the line?i sounds like your diff is the main problem here not tyres try doing it up a small bit and try the car on the track keep doing this till it pulls straight line also cheack the alinement of the rear pod with the chassis and ajust the turnbuckle if needed also check the tweak and the weight blance of the car if you do all this and it still dose it make shore nothing is bent or broken i have seen a few warped chassis

tisher
16-10-2012, 03:35 PM
Right guys first thing cheers for all the advise it has been well appreciated.


Are you all ready for the epic FAIL of the week I have just gone through all the car again and you are not going to believe what I have c....ked up on.
In my infinite wisdom I decided last week to leave the body post full size as I have not got my new shell yet. Here's the best bit the rear posts had completely locked the sag out of the back of the car holding it up at about 6mm and had absolute no suspension at all completely rigid:woot::lol:

I thought on the night the is no way shumacher would make a car this bad :lol:

On a plus note I was only one lap off the pace god help them friday:D

Cheers everyone who have posted some great help:)

joker
16-10-2012, 04:37 PM
pms!!!!!!:woot::woot::woot::woot:

reg
16-10-2012, 05:30 PM
:woot:

SlowOne
16-10-2012, 07:25 PM
I am not laughing... not even sniggering... I am crying with laughter!!!! :cry: :lol:

Cruel, I know. If I've made this sort of schoolboy error once, I have done it a hundred times. The moral of the story is always the same - if something happens to a good car that everyone else finds just fine, go back and check, check and check again because the chances of one having dropped clanger are better than David Cameron voting Tory.

Glad it's sorted though, only one thing worse than a cock-up; a mystery... ;)

tisher
20-10-2012, 06:12 PM
much better last night guys managed to get 4th place even tho I was leading until I was took out on numerous occasions.
Really struggled with the core rc esc the reverse does not seem to want to come in quick enough ended up doing a 20sec lap on a 11 sec track in the final because of it.
Is there any escs that don't have a delay for reverse.
Another thing tho there seems to be alot of cars that are quicker by long way compared to mine is there any way to make it quicker with out cheating:lol:

mark christopher
20-10-2012, 07:20 PM
much better last night guys managed to get 4th place even tho I was leading until I was took out on numerous occasions.
Really struggled with the core rc esc the reverse does not seem to want to come in quick enough ended up doing a 20sec lap on a 11 sec track in the final because of it.
Is there any escs that don't have a delay for reverse.
Another thing tho there seems to be alot of cars that are quicker by long way compared to mine is there any way to make it quicker with out cheating:lol:
lots of clubs/nationals dont allow reverse.
see if there running blinky, if not add some timing

tisher
20-10-2012, 07:36 PM
so even if you ramp up the timing on the motor you are still within the rules :woot: I think I might do that next week Nice one:thumbsup:

cr1tch
20-10-2012, 11:08 PM
so even if you ramp up the timing on the motor you are still within the rules :woot: I think I might do that next week Nice one:thumbsup:

Martin Give me a shout at the club i will be happy to help, though i wont make you as quick as my mardave :p:p:p:p

mark christopher
21-10-2012, 01:35 PM
so even if you ramp up the timing on the motor you are still within the rules :woot: I think I might do that next week Nice one:thumbsup:

What rules do ur club run too, mine is open Speedo

Joe_K
25-10-2012, 03:01 PM
Hi guys,Just bought a SupaStox and will be running it in 2S 21.5T.Just a few questions for those of you with more experience of these cars really.

1) I'll be running this on a fairly open track (30M straight). What rollout should I be looking at? 70-ish MMPR?

2) What sort of tyre diameters do you go for? Where do you start from? 51mm on the rear?

3) What tyre diameter split do you run rear to front? 2.5mm? 3.5mm?

4) What shells work? My current thinking is to go with the Ascari.

5) I've noticed that my steering blocks are a tight fit onto the metal steering posts. What were your solutions? Should I just file it out a little with a needle file or is there a better way?

Cheers folks, looking forward to seeing what these cars can do.Joe

Chequered Flag Racing
25-10-2012, 03:39 PM
Hi guys,Just bought a SupaStox and will be running it in 2S 21.5T.Just a few questions for those of you with more experience of these cars really.



4) What shells work? My current thinking is to go with the Ascari.
Ascari is safe, Lotus is pointy


5) I've noticed that my steering blocks are a tight fit onto the metal steering posts. What were your solutions? Should I just file it out a little with a needle file or is there a better way?
Sounds like you've nipped up the stub axle to much. Back the nut off and report back. If no better run a drill bit through by hand.



and if you don't get the answer your looking for try here https://www.facebook.com/groups/336445139755237/ ;)

mark christopher
25-10-2012, 06:04 PM
Hi guys,Just bought a SupaStox and will be running it in 2S 21.5T.Just a few questions for those of you with more experience of these cars really.

1) I'll be running this on a fairly open track (30M straight). What rollout should I be looking at? 70-ish MMPR?

2) What sort of tyre diameters do you go for? Where do you start from? 51mm on the rear?

3) What tyre diameter split do you run rear to front? 2.5mm? 3.5mm?

4) What shells work? My current thinking is to go with the Ascari.

5) I've noticed that my steering blocks are a tight fit onto the metal steering posts. What were your solutions? Should I just file it out a little with a needle file or is there a better way?

Cheers folks, looking forward to seeing what these cars can do.Joe



hi joe i only run 1s 13.5 so not much help on that (get a 1s and 13.5 would be my recomendation) as you can then do nationals should you wish
1/ 13.5 im around 65 to 70
2/3 i started at 50mm rear with 2mm split and found that fine
4/ my club had no shell restriction so i run the touring car, but the ascari is good with the lotus seeming to be the "choice" however im not sure what was run at the recent national
5/ i had this on mine and found that if you slaken the nut that holds the king pin in the steering block it does not do it, theory was that as i tightend the nut the hex in the block twisted slightly distorting the plastic.

Chequered Flag Racing
25-10-2012, 08:36 PM
however im not sure what was run at the recent national


as per rules

top ten from Sunday

Adam Catchpole / Lotus
Chris Ashton / Ascari
Mark Jewitt / Ascari
Peter Craig / Lotus
Jamie Mcdonagh / ?
Glenn Atterton / Ascari
Graham Oliver / Ascari
Stephen Dobson / ?
Barry Manning / ?
Mick Harris / ?

mark christopher
25-10-2012, 08:44 PM
as per rules

top ten from Sunday

Adam Catchpole / Lotus
Chris Ashton / Ascari
Mark Jewitt / Ascari
Peter Craig / Lotus
Jamie Mcdonagh / ?
Glenn Atterton / Ascari
Graham Oliver / Ascari
Stephen Dobson / ?
Barry Manning / ?
Mick Harris / ?

glen i meant as in the lotus/ascari as your list ;) Joe's 21.5 would not be "as per rules"

tisher
26-10-2012, 11:07 PM
Right guys after a bit more advise:) second proper run out tonight the car is getting quicker now but I am seriously struggling with grip roll:woot: I am running 37 rear 50 front its that bad I have been hardly putting any additive on any ideas guys as this cost me badly in the final:cry:I forgot to mention I moved out the rear springs into the middle and this helped a little bit

neallewis
26-10-2012, 11:44 PM
Right guys after a bit more advise:) second proper run out tonight the car is getting quicker now but I am seriously struggling with grip roll:woot: I am running 37 rear 50 front its that bad I have been hardly putting any additive on any ideas guys as this cost me badly in the final:cry:I forgot to mention I moved out the rear springs into the middle and this helped a little bit

Run 4mm ride height all round. it may dip to 3.5mm under cells. 60 shore fronts, inner 1/2 additive, full additive on rears. I run stiffer springs than kit, red fronts, blue rears I think, might be green fronts? I run middle holes on rear pod. Are you running orings on links?

joker
27-10-2012, 12:10 AM
im running 37 and 50 and i never put any additive on them dont think that you have to put additive on them try runing it with non next time ive got the kit springs on but i have move the rear springs to the outer holes and ive got red o rings on all the links. 4mm ride hite ive got no hint of grip roll and its very good

neallewis
27-10-2012, 12:30 AM
I was grip rolling lots running no additive. Soon as I started plastering it on for every race, grip roll went. I took some advice from some of the more experienced 1/12th racers in my club, who all said the additive stops you grip rolling. By not running it, the tyres slip then grip hard, causing the grip rolls. It starts off fine, then as the grip comes up during the evening, the roll gets worse. Running additive every race got rid of my grip roll. A high car, or really high walled un-trued tyres will also have it however. if you have taken care of that, plaster on the additive...

tisher
27-10-2012, 10:09 AM
A couple of different opinions there:) I found the beginning of the meet the car was brilliant I was 2nd overall until round 3 when it started biting in and grip rolling I was running less additive so maybe I will try banging loads on and see what it does:) I will get hold of a spring set as well to try harder springs. I am running the kit o rings as well something I have noticed is that you can not get the front of the car down to 4mm

CAT3K
27-10-2012, 10:55 AM
A couple of different opinions there:) I found the beginning of the meet the car was brilliant I was 2nd overall until round 3 when it started biting in and grip rolling I was running less additive so maybe I will try banging loads on and see what it does:) I will get hold of a spring set as well to try harder springs. I am running the kit o rings as well something I have noticed is that you can not get the front of the car down to 4mm

Flip the m3 nuts on the front springs over so it's nyloc side down, then you can run the nuts higher on the screw and get the front end as low as you like :)

joker
27-10-2012, 12:13 PM
ye do what cat3k said you my need to put some more washers under the wishbone think where all running about 4/5mm of washers you can get them down to 2mm ride hite evan with full tyres

neallewis
27-10-2012, 01:43 PM
A couple of different opinions there:) I found the beginning of the meet the car was brilliant I was 2nd overall until round 3 when it started biting in and grip rolling I was running less additive so maybe I will try banging loads on and see what it does:) I will get hold of a spring set as well to try harder springs. I am running the kit o rings as well something I have noticed is that you can not get the front of the car down to 4mm

That's exactly the situation i was finding. Run more additive. I'm on red fronts and blue rear springs, but green work well on front also. Reversing the front lock nuts is an option or swapping the 30mm bolts for 35mm.

Apricot Slice
28-10-2012, 12:06 AM
I want to help if I can but am too lazy to read the whole thread so excuse me if I am repeating things.

I would make sure there is no sloppiness in the grommet department.
If the grommets squidge about under cornering load it will cause additional steering and nackker your driving. (chassis flex will do the same thing because of the big distance between servo mounts and suspension mounts.)

I am running kit (sstox) tires, green springs on front and mardave pod at rear with no diff. (sstox rear is silly) It feels pretty good. My test driver has a diff in his and raced twice and got first and a second.

SlowOne
28-10-2012, 08:05 PM
I realise it is counter-intuitive, nonetheless when the grip comes up you need the car to be softer. Additionally, the car needs to have smaller diameter tyres to remove some sidewall flex. Try 45mm fronts and 47mm rears.

You can also brush superglue on to the sidewalls of the front tyres to remove some grip, but that should only be in extremely high grip. The glue should be sidewall only, to the top of the sidewall, but not any on the tread of the tyre.

I see lots of cars where drivers are going harder and harder on the springs and tyres as the grip comes up, and then having grip-roll. The reason that it works better if you put some additive on is because that softens the tyre. As a rule of thumb, as the grip comes up use softer fronts. If the level of grip locks the rear in, then go to a harder rear.

50 front is too hard for your carpet. Go down to a 45 and see what happens, if necessary go to a 42. IF you can true them down to 47/45 then do so.

I do think from your description there is something up with the car, so a rebuild with the instructions in front of you might not go amiss. I've been doing this for 35 years, and mistakes made when building the car are still in my repertoire! HTH :)

tisher
28-10-2012, 08:45 PM
I realise it is counter-intuitive, nonetheless when the grip comes up you need the car to be softer. Additionally, the car needs to have smaller diameter tyres to remove some sidewall flex. Try 45mm fronts and 47mm rears.

You can also brush superglue on to the sidewalls of the front tyres to remove some grip, but that should only be in extremely high grip. The glue should be sidewall only, to the top of the sidewall, but not any on the tread of the tyre.

I see lots of cars where drivers are going harder and harder on the springs and tyres as the grip comes up, and then having grip-roll. The reason that it works better if you put some additive on is because that softens the tyre. As a rule of thumb, as the grip comes up use softer fronts. If the level of grip locks the rear in, then go to a harder rear.

50 front is too hard for your carpet. Go down to a 45 and see what happens, if necessary go to a 42. IF you can true them down to 47/45 then do so.

I do think from your description there is something up with the car, so a rebuild with the instructions in front of you might not go amiss. I've been doing this for 35 years, and mistakes made when building the car are still in my repertoire! HTH :)


Cheers for the advise I dont think I have done any thing wrong building the car but there must be something I am doing wrong as I used to get the same problem with the dave the only thing I can not do is true the tyres down as I have no way of doing this I always have to run them out of the box maybe this is the problem i dont know:thumbdown:

SlowOne
29-10-2012, 06:39 AM
The latest batches of Contact tyres will be coming in at 45 front and 47-ish rear, so hang in there!

neallewis
29-10-2012, 11:05 AM
Cheers for the advise I dont think I have done any thing wrong building the car but there must be something I am doing wrong as I used to get the same problem with the dave the only thing I can not do is true the tyres down as I have no way of doing this I always have to run them out of the box maybe this is the problem i dont know:thumbdown:

If you had the same problem it must be tyre related. did you coat them with additive?
If you run your tyres a bit, they wear down, no need to true ;-)
Has anyone at your club got one that they can bring on a race night, or let them take home a set of your tyres to true down for the next meeting?

KJR
30-10-2012, 08:17 PM
The latest batches of Contact tyres will be coming in at 45 front and 47-ish rear, so hang in there!

This is a real shame. I normally start my tyres at 49 rear and 47 front. If you happen to be running a non adjustable rear pod then it means you will only get about 2mm of wear before you run out of rear ride height on a mardave.

Better get stocked up now !!

Dave Dodd
30-10-2012, 08:53 PM
omg, cant believe they are changing the diameter again :cry: .... just got my car working gr8 on 52mm + they last longer.. now gonna be 47mm :eh?:

SlowOne
01-11-2012, 08:16 PM
You'll find the new tyre sizes will be worth it for the handling improvement you'll get. ;)

4_cell_racer
02-11-2012, 02:15 AM
You'll find the new tyre sizes will be worth it for the handling improvement you'll get. ;)
But will they be cheaper lol :D

GhostlyRock
02-11-2012, 05:21 PM
Take note of what the slowone says, 1/12th guys have loads of experience running foams and fighting grip roll. The smaller the tyres dia. generally you will get less grip roll due the rubber not moving across the tyre as much.
I bit the bullet, trued my tyres, 45.5/46.5, 35 rear 47 front, still run the kit springs, car handles a dream. If you still get it in high grip situations, superglue the front sidewalls and go for a softer spring, trust me it works.

Leelosi
04-11-2012, 11:50 PM
mine was the same,untill i fitted the diff,total changed the car,its ace to drive now:thumbsup:

And to make it even better buy the front suspension kit from schumacher. But don't forget the 4 grommets you need to buy. Pain to get in but I used a littlle fairy liquid to persuade them in to position

Addicted2blue
10-11-2012, 12:53 PM
Is there a special tool needed to true down the tires for the supastox?
I'm just asking this because last wknd i saw these cars at the track i went and they look great so i'm considering to buy one of this great cars.
So i have no idea of what the wheels look like on the inside, just asking this to know more of what i'm willing to start with

Martyn (Bomber)
10-11-2012, 01:26 PM
Is there a special tool needed to true down the tires for the supastox?
I'm just asking this because last wknd i saw these cars at the track i went and they look great so i'm considering to buy one of this great cars.
So i have no idea of what the wheels look like on the inside, just asking this to know more of what i'm willing to start with

There is a tool called a Tire Truer that will take down your tires to whatever diameter you want but most people now just buy the Contact's that are already trued & glued, here are a list of whats available ;)

http://www.racing-cars.com/sp/category/Manufacturer/subcategory/Contact_RC/templateid/12/searchbox7/1-12_Foams;_Supastox-Mardave.html

Addicted2blue
10-11-2012, 01:54 PM
I have already a tire trues on order, it's on it's way to me but that wasn't the question.
The question was do i need a special tool to be able to true down the supastox tires on the tire truer.
Meaning the mounting tool on wich you mount the tire/wheel what kind of tool is it that you would need.
As far as i know of there are 4 kind of mounting tools, for 1/8th scale wheels (wich i think it won't fit in the wheels), for 1/10th scale touring car wheels, for 1/12th scale pan car wheels or for Tamiya F1 wheels.

Getpip
10-11-2012, 02:03 PM
The item you need is called an Arbor.
Try here...
http://www.mardavespares.com/foam-tyres-accessories/tyre-truers-arbors/mardave-racing-tyre-truer-arbour

Or here...
http://www.activescalemodels.co.uk/mardave-g47-tyre-true-arbour-14403-p.asp

Chequered Flag Racing
10-11-2012, 02:08 PM
The item you need is called an Arbor.
Try here...
http://www.mardavespares.com/foam-tyres-accessories/tyre-truers-arbors/mardave-racing-tyre-truer-arbour

Addicted2blue

If the truer doesn't have a threaded shaft you'll need to drill, tap & grub screw the Mardave arbour and file a flat on the truer shaft. Or you can drill through the arbour and shaft and use a strong body clip to hold it in place.

If the truer has a threaded shaft then the Mardave arbour just screws on if the threads are the same.

Addicted2blue
10-11-2012, 02:23 PM
The item you need is called an Arbor.
Try here...
http://www.mardavespares.com/foam-tyres-accessories/tyre-truers-arbors/mardave-racing-tyre-truer-arbour

Or here...
http://www.activescalemodels.co.uk/mardave-g47-tyre-true-arbour-14403-p.asp

Thank you very much, that was the answer i was looking for :)

Kind regards

SlowOne
10-11-2012, 06:35 PM
Please check which truer you have ordered. Does it have a screwed shaft that will fit the Mardave arbor? Most have a plain 8mm shaft and that arbor will not fit. If you don't have the tools to modify the arbor as Glenn said, you're a bit stuck!

Strangely, neither Mardave nor Schumacher do an arbor that fits an 8mm shaft, and more truers have that attachment than any other!!

mark christopher
10-11-2012, 07:23 PM
you mean like this pete?

http://sphotos-f.ak.fbcdn.net/hphotos-ak-prn1/544991_10150785563921156_56361301_n.jpg

SlowOne
10-11-2012, 10:19 PM
Yup, that's the one. I made my own from an old Integy TC arbor and the axle from a PB Mustang! Is that commercially available? If it is, Addicted needs one! :)

Martyn (Bomber)
11-11-2012, 03:24 AM
The question was do i need a special tool to be able to true down the supastox tires on the tire truer.

No! This was not your first question, you asked "Is there a special tool needed to true down the tires for the supastox?" as I don't know your level of knowledge I answered a Tire Truer.

All sorted now tho :D

mark christopher
11-11-2012, 06:11 AM
Pdw unfortunately not its one I had

Addicted2blue
12-11-2012, 05:52 PM
Please check which truer you have ordered. Does it have a screwed shaft that will fit the Mardave arbor? Most have a plain 8mm shaft and that arbor will not fit. If you don't have the tools to modify the arbor as Glenn said, you're a bit stuck!

Strangely, neither Mardave nor Schumacher do an arbor that fits an 8mm shaft, and more truers have that attachment than any other!!

I've ordered a 3 Racing tire truer, don't know what shaft it has. When it arrives i will check it :)

@Martyn (Bomber): with that special tool i ment the arbor (just didn't know the correct word for it, but still thx for answering)

SlowOne
12-11-2012, 09:12 PM
That truer has an 8mm shaft for the arbor. HTH :)

Addicted2blue
12-11-2012, 10:06 PM
that means bad luck :(
I thought the arbors are universal, guess i need to find another solution.

Addicted2blue
13-11-2012, 09:44 AM
Perhaps maybe the arbor from the following link is designed for a regular 8mm shaft or isn't it, doesn anybody know this for sure?
http://www.activescalemodels.co.uk/m...ur-14403-p.asp (http://www.activescalemodels.co.uk/mardave-g47-tyre-true-arbour-14403-p.asp)

mark christopher
13-11-2012, 10:15 AM
it is but your shaft needs to have a thread on the end

mark christopher
13-11-2012, 11:05 AM
sure 3 racing truer is 8mm not sue if it has the threads though

Chequered Flag Racing
13-11-2012, 11:46 AM
I have a TopCad truer. 8mm plain shaft. Drilled and tapped Mardave arbor and filed a flat on the shaft.