PDA

View Full Version : Cat K1 Setups


Mossy
09-12-2012, 10:37 AM
Attached below is the setup i used at Silverstone Winter Series yesterday - high grip astro/carpet. I have found over testing that this is a good base starting setup and have been using at most places. The only changes I made yesterday was to go up 50wt all round.

Si

OneKiwi
09-12-2012, 12:30 PM
silly comment sorry

cmgreen
09-12-2012, 12:46 PM
Is that using core rc oil si?

Mossy
09-12-2012, 01:19 PM
Yeah Core Rc Oil

Mossy
02-01-2013, 11:26 AM
Any chance of making this thread sticky? People are already commenting that we could do with a setup section. I will do my very best to put new setups up when i test/race etc and Im sure Tom, Grant, Danny & Llloyd will do the same where possible.

Si

Mossy
02-01-2013, 11:51 AM
Kiddy Test Day & my starting setup for Worksop this Sunday

tyreman
02-01-2013, 05:22 PM
Simon is that right on the setup sheet, that you use 1.2mm pistons in the rear and 1.3mm in the front, or is that an error on the sheet?

mark christopher
02-01-2013, 06:57 PM
white = 1.2
black = 1.3
red = 1.4

tyreman
02-01-2013, 07:48 PM
white = 1.2
black = 1.3
red = 1.4

Mark thats not the question i was asking, and i was asking Simon.

mark christopher
02-01-2013, 08:23 PM
Mark thats not the question i was asking, and i was asking Simon.

sorry just rying to help!!
on simons set up sheets are piston colours which tie to the sizes
doubt simon would enter, the wrong piston colour and sizes down wrong

tony12795
02-01-2013, 08:25 PM
Preddy, yes that's right.

I also asked the question at Silverstone, Si runs smaller hole piston in the rear

chuckie stella
02-01-2013, 08:55 PM
Didn't work for me, then again we don't all have his thumbs!! :lol:

tony12795
02-01-2013, 09:12 PM
@ Father Christmas

SNAP!!

tony12795
02-01-2013, 09:12 PM
Ignore

Mossy
02-01-2013, 11:29 PM
The setup sheet is correct to what I've been running. To be honest I have been messing around with pistons in the front and this just what I have settled on for the time being. I run the setup with the bigger pistons in the front as at Silverstone I wanted the back to be pretty damped but the front to dip into the corners at low speed.

At Worksop I might well change this a little as I will want more rear end.

Si

Mossy
12-01-2013, 03:37 PM
Attached is the setup i finished on at Worksop last week, my apologies for the delay. I made a lot of changes throughout the day and this is the setup i ran in the final. Was really pleased with the car in the final, nothing between me and Nath Waters (if any of you saw the final) and not massively slower than Neil. The car was far more balanced on the shock settings and handled the table tops etc much better. The majority of my changes were to generate low speed steering, hence the extra washers under the front inner ball stud. Ill be starting with this exact setup tomorrow at Broxtowe, so any comments/ discussions please feel free to ask.

Cheers

Si

cmgreen
12-01-2013, 06:45 PM
Si see ur running the option chassis, is this carbon or s1?
Also the rear blocks your running rear low frong high, what does this do?

mark christopher
12-01-2013, 07:19 PM
Si see ur running the option chassis, is this carbon or s1?
Also the rear blocks your running rear low frong high, what does this do?

simon had a s1 but i believe it was still a test item
simon also runs the alloy rear blocks and fine tunes with washers, which you can not get with the kit part. (sat next to him at worksop and asked the same)

Razer
13-01-2013, 09:57 PM
So, this weekend was my debut with this beast, at the Petitrc race held at a cementhard clay track with varying grip, horribly executed jumps, and a reputation for killing any car you throw at it.

With the Schumacher in kit form, even though responsive and well jumping, this wasn't it's favourite playground. But I've only broken one suspension arm through a weekend of racing, and I now got a decent setup for clay:)

I switched to the white piston up front, Losi 40 oil, TLR green springs(3.5) and 7.5 yokes.
In the rear I had Losi 35 oil(felt heavier than kit), TLR yellow springs and a 1.3 mm Yokomo B-max roll bar, with a custom mount.

I was testing a few oils and springs, but this is what turned out best so far. I didn't have time for testing any links, toe adjustments and such, and the car is still a bit on edge, but this setup made me have the A-main pace, even if I couldn't deliver.

So far so good, I'm looking forward to more testing:)

Mossy
30-01-2013, 07:07 AM
Had a couple of pm's asking for my setup from Worksop on Sunday so i will do my best to get it up when i'm back from work tonight. My car was fantastic, best I have had it so far so hopeful I might have found a better base setup.

Si

Mossy
30-01-2013, 10:30 PM
Sundays setup guys, any questions let me know!

mark christopher
30-01-2013, 10:44 PM
Hi simon

Are they core springs?

TARTMAN
31-01-2013, 12:48 AM
I have been running the K1 is standard trim for a few meetings now. decided sunday at Torch, needed to start "adjusting/changing" things.
Mr Saddler, the most awsome dude surgested putting the rear end on the higer setting holes. did this. was unsure of the result 1st round after the change but have to say it worked for a bumpy track(torch), will go back to the lower settings for SHRCCC as a little smoother and its awsome there.
I also, added what a few people questioned as a LOT of under lipos weight. 110grams. The track was VERY wet, and i have to say made the car corner, grip and jump SOOOO much better. Well it did for me.

Yes it was alot of weight as a 1st try but the car was so much more stable and jumped perfectly. that i will be keeping the huge weight for the wet, maybe half that for the dry to start, but not had any track time in the dry as yet to try it(love the UK weather).
So, anyone struggling with jump/grip/handling, try some heavy weight(i use lead) under the pipos. you might like it..............;)

Mossy
31-01-2013, 06:42 AM
Yeah Core Rc springs

cmgreen
31-01-2013, 07:13 AM
And big bore shocks

chrispattinson
31-01-2013, 07:17 AM
Hi Simon ,
Regarding the anti squat, I'm not sure what the setup sheet is showing with the alloy block settings ...... So front high, rear low, but then lower the front by 1.5mm with the shims. Is my understanding correct?

cmgreen
31-01-2013, 10:09 AM
Hi Simon ,
Regarding the anti squat, I'm not sure what the setup sheet is showing with the alloy block settings ...... So front high, rear low, but then lower the front by 1.5mm with the shims. Is my understanding correct?

Think i can make out 3mm at the front none at the rear

chrispattinson
31-01-2013, 10:13 AM
Think i can make out 3mm at the front none at the rear

Yeah, I see that, but in the difference table it appears to read 1.5mm? The problem may be I don't understand how to read the setup sheet properly.

Andrew Twigger
31-01-2013, 10:22 AM
Unless the 3mm compensates for the front block being mounted in the 'high' position? If that's the case, what would be the advantage of running high front and low rear if the spacers are used to make the anti-squat the same anyway?

Even more confusing that the table itself tells you overall rear toe and not anti-squat too!

Cruise
31-01-2013, 10:24 AM
If you want to get the rear pin higher you will sometime hit the point when you canīt remove more washers.That will most likely happen in the front,so you put that one hole higher.As you want a short stack for bending reasons you leave the rear in the lower hole.


Cruise

chrispattinson
31-01-2013, 10:38 AM
Even more confusing that the table itself tells you overall rear toe and not anti-squat too!

Glad it's not just me Andy.

Mossy
31-01-2013, 08:59 PM
I run the pin high front/ low rear combination because i feel for me it gives me the most balance on the car. I find running pin high all rounds means the car rotates through the corner too much and pin low means loss of forward traction again in my opinion. This is something i ran on my SX3 and when testing put on my K1 and it made a big difference.

What you have to remember is that if you dont space the front block down when running this combination, you would technically be running 4mm worth of anti squat as the difference in hole height is 4mm. I space the front pin down by 2.5mm, therefore giving a an overall antisquat of 1.5mm, hence 1.95 degrees of squat. The calculation is worked out the same for toe in and antisquat, its just a typo on the setup sheet. Ralf's point of having to run this configuration is not correct, its just personal preference for me.

And yes I am running big bores at the moment.

Hope this helps!

chrispattinson
01-02-2013, 07:57 AM
Thanks Simon, it's good to get a bit of logic behind the setups. I'll give this setup a try on Sunday.

Cockerill
12-03-2013, 10:08 AM
My recent setups have been posted on Petit RC (http://www.petitrc.com/setup/schumacher/SetupSheetsSchumacherCatK1.html)

Worksop setup is here: http://www.petitrc.com/setup/schumacher/setupcatk1/K1_TomCockerill_Worksop20130310/

hansie
16-03-2013, 01:03 PM
Hello all,

I was wondering if anyone can tell me if the following part would fit on a K1

U3529 (a conversion for the SX)

If it fits it would give more rear camber link options instead of buying 3 different rear plates.

Greetings

Hans

ulrich
17-03-2013, 09:21 PM
Hello all,

I was wondering if anyone can tell me if the following part would fit on a K1

U3529 (a conversion for the SX)

If it fits it would give more rear camber link options instead of buying 3 different rear plates.

Greetings

Hans

This part dosenīt fit on the K1. If you want the options you have to buy two parts U4169 & U4170, the third is standard in kit.

hansie
22-03-2013, 05:33 AM
Hello,

Thanks for the reply, I will get the K1 parts then.

Greetings

Hans

zoomzoombang
22-03-2013, 04:03 PM
can anyone tell me the size of holes for the stock pistons? I am getting a 2nd hand K1 and for the life of me cannot find this info anywhere. Thanks. Also any pointers to useful :D upgrades will be appreciated.

mw02veg
22-03-2013, 04:43 PM
1.5mm

matdodd
22-03-2013, 07:57 PM
The kit black pistons in the K1 are 1.3mm

Ive found the U3404 Alloy Yoke 7.5deg and U4160 Rear Alloy Block Conversion Set are usefull upgrade

Mat

zoomzoombang
25-03-2013, 03:09 AM
matdodd: Thank you for the upgrade suggestions.

mw02veg & matdodd: so are the pistons 1.3 or 1.5? Still confused. Thanks :blush:

paulc
25-03-2013, 06:22 AM
White 1.2 mm
Black 1.3 mm (kit)
Red 1.4 mm

mw02veg
25-03-2013, 06:26 AM
My bad 1.5 is for big bore pistons
:cry:

zoomzoombang
25-03-2013, 07:57 AM
mw02veg & paulc: thanks for clarifying!

Thomas B
27-04-2013, 10:25 PM
Will it work to have the kit molded blocks in the position like in mossys setup? Rear low and front high. Or do i need the alu blocks?

stegger
28-04-2013, 04:37 PM
Will it work to have the kit molded blocks in the position like in mossys setup? Rear low and front high. Or do i need the alu blocks?

Alloy blocks mate. :)

corsair
29-04-2013, 02:49 AM
Has anybody tried the gear diffs into the setups?
The quality of the mouldings look good.

jimlee
29-04-2013, 07:36 PM
Anybody tried the gear diffs yet?
Works well for us on the polished wooden floors but disappointed at them leaking.
Anyone else have the same problem?

ulrich
29-04-2013, 08:53 PM
We tired them on astro, no leaking at all.. very pleased with them. At the temperature we have here in Denmark at the moment (have not seen spring yet and temp. around 10-13 deg. C), we found the 10000 and 5000 setting to stiff, until now we found 5000 front and 2000 rear best, will go for a 3000 in front next time.

badger5
01-05-2013, 06:25 AM
I see that the Schuey site says that 7000wt oil is a good all round starting point for astro but it would be good if there could be some more info on this.
The point of leaking could be down to the diff being overfilled, some guidelines on this would also be helpful, maybe another video.

stegger
10-05-2013, 11:03 PM
Anymore info on diff oils people are using would be a great help....
For say the southport track. Wet and dry conditions !

spud31
22-05-2013, 06:17 AM
Anyone got a polished wood floor setup for the k1?

merlin_341
22-05-2013, 06:45 AM
Anymore info on diff oils people are using would be a great help....
For say the southport track. Wet and dry conditions !

I run 7000 front and 3000 rear works great but have not tested on loose dirt yet but it feels like it should work

richardh
26-05-2013, 07:31 PM
Hi spud31,

I'm running the k1 on polished wood, this is my setup at the moment:

Front:

Standard small bore pistons, with 30wt oil and white core rc springs.
Shocks mounted in the middle on the tower and inside on the wishbone. Running 15deg of caster. 1 dink link mount, no spacers underneath. Zero toe and -1.5deg camber. Gear diff with 10k, though tempted to go down to 7.5k

Rear:
Red pistons, 30wt oil, core rc red springs. Middle hole on tower, outside on wishbone. Silver anti roll bar. 3dink mount with 4mm spacers underneath stud, middle hole on hub. Std toe, -1.5deg camber. Wishbone on low roll centre, with 3deg anti squat. Gear diff with 10k oil, though tempted to try 7.5k

Cells in forward position position with alloy chassis.

Toying with running the carbon chassis, but not 100% convinced convincedabout this for polished wood due to the weight loss...?

Hope that helps.

Richard

spud31
27-05-2013, 12:00 PM
Hi thanks for that what tyres are you running ?

richardh
27-05-2013, 07:48 PM
Running yellow mini-spikes - so long as the floor is clean and not too dusty the more worn they are they better.

spud31
27-05-2013, 08:34 PM
Hi im pretty close yo your setup running 5k front 2k rear and big bores with 3 hole pistons 35w front 30w rear core black front green rear springs
long wheel base and 2mm spacing on ackerman plate
I ran 30g plate under each battery which improved it.
am toying with s1 chassis to generate even more grip,

phoenix
01-07-2013, 05:48 PM
Does anybody have K1 setups from last weekend in Belgium, e.g. the Kampenhout track? Thanks !

Cockerill
02-07-2013, 06:47 AM
My Setup should be online later today or tomorrow, I will post a link when it's up!

Cockerill
02-07-2013, 10:53 AM
My Setups are posted, thanks to Arn0 :thumbsup:

http://www.petitrc.com/setup/schumacher/setupcatk1/K1_TomCockerill_Kampenhout2013062830/

http://www.petitrc.com/setup/schumacher/setupcougarsv2/CougarSV2_TomCockerill_Kampenhout2013062830/

Robbiejuk
02-07-2013, 12:14 PM
My Setups are posted, thanks to Arn0 :thumbsup:

http://www.petitrc.com/setup/schumacher/setupcatk1/K1_TomCockerill_Kampenhout2013062830/

http://www.petitrc.com/setup/schumacher/setupcougarsv2/CougarSV2_TomCockerill_Kampenhout2013062830/

Ball diff in the front and Gear in the back in the K1? Very interesting. How does that feel compared to Ball diff all round?

phoenix
11-07-2013, 08:33 PM
My Setups are posted, thanks to Arn0 :thumbsup:

http://www.petitrc.com/setup/schumacher/setupcatk1/K1_TomCockerill_Kampenhout2013062830/

http://www.petitrc.com/setup/schumacher/setupcougarsv2/CougarSV2_TomCockerill_Kampenhout2013062830/

Thanks Tom !

Cockerill
12-07-2013, 06:38 AM
Ball diff in the front and Gear in the back in the K1? Very interesting. How does that feel compared to Ball diff all round?

I completely missed this post!

In my limited running of gear diffs I've found that putting a gear diff in the rear gives the car a lot more drive out of corners. Keeping the ball diff in the front still allows the car to take rough/bumpy tracks pretty well.

stegger
12-07-2013, 06:48 AM
Are you running the front ball diff Tom as per kit setting ? or looser / tighter.

Cockerill
12-07-2013, 07:43 AM
Just as per kit

Robin A
06-10-2013, 05:57 PM
With the Worksop series starting a week today, please could one of the Schumacher guys suggest a good starting set-up. Preferably with gear diffs, alloy rear blocks, and 7.5 front yokes.

Also, it'd be interesting if they could detail if they are going with small or big bores, or if they are waiting to see the track before making that decision?

Kurtje
16-10-2013, 08:19 AM
Can anybody tell me what's the best setup for the belts? What is the right tension on them?

iggihk
17-10-2013, 04:39 PM
Can anybody tell me what's the best setup for the belts? What is the right tension on them?

I set them on the loosen side , as i found the car run smoother and not over heating after i loosen the belts as lose as possible (without skipping )

Kurtje
18-10-2013, 04:40 AM
Ok thank you.

I've watched some video's on youtube and they say the tension is good when you can move with your finger the belt a couple of mm's up and down.

badger5
18-10-2013, 07:26 AM
I see from Tom Cockerill's worlds set up sheet he was using the SV2 rear suspension arms, what difference will this make and are more parts required other than the suspension arms?

bobbin
18-10-2013, 10:34 AM
I see from Tom Cockerill's worlds set up sheet he was using the SV2 rear suspension arms, what difference will this make and are more parts required other than the suspension arms?

longer wheelbase see the link
http://www.petitrc.com/setup/schumacher/setupcatk1/K1_JohnSpencer_Valladolid2013071820/

Cheers
Robin

xtream
21-10-2013, 05:45 PM
has anyone an indoor carpet setup for the k1? may be with gear-diff?

thx

madmulc
02-11-2013, 12:51 PM
Hi

I was wondering if anybody had there setup for round one at worksop?

Cheers

James
24-11-2013, 09:03 PM
Hi

I was wondering if anybody had there setup for round one at worksop?

Cheers


This is my setup from Batley today, the car was amazing, managed to win.
The setup is the same apart from change rear springs to black for worksop and front springs to blue.

Dodgy Guy
24-11-2013, 09:23 PM
This is my setup from Batley today, the car was amazing, managed to win.
The setup is the same apart from change rear springs to black for worksop and front springs to blue.
Cheers for sharing this James. Your car looked excellent!
Great driving - well done!

spud31
24-11-2013, 10:19 PM
James
cant view this again, v small then if enlarged unreadable

Hans Wynants
05-02-2014, 07:24 PM
i can assume that this tread also will work for the Aero version? :lol:

is there anyone who hase a set up for the past EOS race in CHALERLOI please?

i will start training there shortly for the BNK race this season , and would like to put on a good set up from the start.

i heard mr. Lloyd Storey has raced there , and his car was very fast.

maybe Mr Cockerill can arrange a good set up ? :thumbsup:


thanks guy's

DragonRider
22-03-2014, 01:41 PM
I am looking at purchasing 2 K1 Aero kits for my boy (his first ever RC Build) and myself to get back into racing.

My son will be running Speed Passion electronics with a V3 8.5 and I will be running Speed Passion V3 7.5

Does anyone have a starting setup to run at TORCH (High Grip Astro) that I shoud start with.

Also any hop ups I need to get to install during the build.

Any help very much appreciated.

Cheers

Mark & Wesley

DragonRider
29-03-2014, 07:47 AM
Hi

Now ordered the 2 K1 AERO kits so just waiting on Mr or Mrs Postie.

I need to order the oils for both shocks and diffs has anyone got a base starting point so I know what to order and start with for high grip astro.

Cheers

Mark

Mossy
29-03-2014, 08:27 AM
Not ran at Torch, but I would be starting with 20k diff oil all round - Shocks would be 450wt 3 hole standard on Core Green for the front, 400wt 3 hole 1.6 on Core Black springs.

I'm not sure what kit pistons are to be honest.

DragonRider
29-03-2014, 08:37 AM
Thank you Mr Moss for the advice very much appreciated.

Cheers

Mark

madmulc
03-04-2014, 12:05 PM
Hi,

I am after a set up for my K1 to run Telford if possible, I cant remeber what setup I ran last yr for regionals Doh!!!!

Note to myself remember to write my set up down and file it :blush: lol

Cheers
Pete

Gayo
22-01-2015, 04:13 PM
What is the preferred chassis on astro? I am a happy owner of a K1 Aero (graphite chassis), I am considering an alloy chassis for the summer season, where I will mainly run on astro.
Most setups last year were with an alloy chassis, even on the slippery dirt of the Euros. Wouldn't the S1 chassis be better on such a slick track?