View Full Version : Jörn MM and shocks rear
OneKiwi
11-03-2013, 06:48 PM
Anyone tried it?
Is it just a remove hubs ( for toe etc), arm flip, shock move?
http://i30.photobucket.com/albums/c338/simonandhanna/Capture-2.png
Lee24h
11-03-2013, 07:10 PM
Anyone tried it?
Is it just a remove hubs ( for toe etc), arm flip, shock move?
http://i30.photobucket.com/albums/c338/simonandhanna/Capture-2.png
very interesting what advantage will it give and presuming for high grip tracks.
burgie
11-03-2013, 07:20 PM
I have been running our 410 bad 210 like that for sometime now. It would appear to calme the rear end down a lot on bumpy sections, and generally help with rear grip.
The big downside is that the shock bodies become your rear bumper...
Si Coe
11-03-2013, 07:23 PM
Its a slightly longer wheelbase, and the weight is further back. Whilst the shocks are more vulnerable at the rear, the shock tower digs in less on rolling so its less likely to break.
Biggest downside is you have to trim the wing to go around the shocks.
OneKiwi
11-03-2013, 09:11 PM
It should give more rear traction, should be pretty good on the RM car as they will be a bit more protected.
Burgie do you have a pic of the 410 like that?
Legacy555
12-03-2013, 08:37 AM
It should give more rear traction
:thumbsup: Yeah, that's what I found - also gives more rotation in tight corners
RichyUK
12-03-2013, 11:09 AM
I am running mine like this again tonight as it goes. all i did was redrill holes in the rear of the wishbone.
OneKiwi
12-03-2013, 01:11 PM
So you didn't flip your arms??
Are you using the dimec as well or stock chassis
RichyUK
12-03-2013, 02:13 PM
So you didn't flip your arms??
Are you using the dimec as well or stock chassis
No, i was going to, but i like the idea of leaving the arms as they are so i can switch the shocks back and forth to test them back to back. i just measured the hole spacing from the front of the arm with vernier calipers and drilled new holes.
I am running the dimec20 chassis on mine :)
OneKiwi
12-03-2013, 02:28 PM
Not a bad idea.. Ill have to see how steady my hands are :woot:
Heres the RM pic from RCTech
http://www.rctech.net/forum/attachments/electric-off-road/1042312d1363019510-durango-dex210-thread-img_1052.jpg
Gregerl
12-03-2013, 06:01 PM
Hi Guys
This subject has me a bit puzzled, I am thinking a bit about what does what.
If you flip the arms over and stay shimmed the same way you were you will actually lengthen the wheelbase some, this will take away rear traction, but it will make it rotate a bit easier if the back end is sliding a bit, and it will calm it down over bumpy sections and probably make it a bit more directionally stable. When you move the dampers rearwards you are moving some weight, so it will give some more rear traction, but I believe not influencing as much as the effect of flipping the arms and thus lengthening the wheel base.
in addition I bet that the rear arms are twisting under acceleration, and the side that will be moving the most is the one where the damper isn't attached, so that will also account for some effect.
All of this will have different impact based on if you flip the arms or re-drill them since it will give different wheelbase and leverage on the arm.
Things to think about when you choose between re-drilling or flipping arms :-)
/Greger
KooBee
12-03-2013, 06:38 PM
Another angle.
http://eos.redrc.net/wp-content/gallery/eos-201213-rd3-leoben-austria/sun-durango-1.jpg
rcjunky
13-03-2013, 03:47 AM
I now have the same chassis and the rear mount shock set up, anyone have under body pics of the 210 and set up?
Mark Field
14-03-2013, 09:46 PM
I have tried re-drilling the wishbones and mounting the shocks on the rear, it does give more traction on slipper surfaces. I did try flipping the wishbones but the wishbones have some toe-in built in. Hence flipping the wishbones is not an option!!!!!
As for steady hands, its no prblem if you measure the hole centers and center punch:)
Durango needs to update the arms so there is another hole for the droop screw when you run the arms backwards:eh?:
I have tried re-drilling the wishbones and mounting the shocks on the rear, it does give more traction on slipper surfaces. I did try flipping the wishbones but the wishbones have some toe-in built in. Hence flipping the wishbones is not an option!!!!!
As for steady hands, its no prblem if you measure the hole centers and center punch:)
You're mistaken, they don't have any built-in toe in.
There is a 2mm wheelbase difference when you flip the wishbones however, so to get the same wheelbase with the wishbones flipped as middle with the wishbones in the normal position, you need to run all the spacers at the back.
dpackster1980
21-03-2013, 10:18 PM
I have tried re-drilling the wishbones and mounting the shocks on the rear, it does give more traction on slipper surfaces. I did try flipping the wishbones but the wishbones have some toe-in built in. Hence flipping the wishbones is not an option!!!!!
As for steady hands, its no prblem if you measure the hole centers and center punch:)
Very wrong indeed.
Toe in is determined by the pivot blocks and the hub inserts only not the wishbones.
dpackster1980
25-03-2013, 08:10 PM
Well I tried it last night on carpet and wooden floor it was really good. I don't think I'll be putting it back to standard I was well impressed. :thumbsup:
brooksy
27-03-2013, 06:42 PM
Any pics with the wheels off from the back?. Just want to know exactly where the holes are on the arms.
Phill
RichyUK
28-03-2013, 09:23 AM
Any pics with the wheels off from the back?. Just want to know exactly where the holes are on the arms.
Phill
i just used my vernier to measure the front ones from the outer hinge pin and replicated on the rear.
brooksy
28-03-2013, 01:30 PM
Cheers Richy,ill have a look at mine later. Have you run yours yet and if so what surface was it on and how did it go?. I'm running the Dimec20 chassis aswell. It will be the first time out on astro for it Saturday.
Phill
RichyUK
28-03-2013, 02:48 PM
Cheers Richy,ill have a look at mine later. Have you run yours yet and if so what surface was it on and how did it go?. I'm running the Dimec20 chassis aswell. It will be the first time out on astro for it Saturday.
Phill
Yes Phill, i've run it a couple of times at my local track Maritime which is a mix of carpet, a little astro and slippery wood. The car certainly feels more planted IMO with the shocks at the rear, less like it wants to break traction whilst cornering :)
brooksy
28-03-2013, 04:26 PM
Ill do mine the same as yours I think,drill holes at the back rather than flip the arms then I can test them against the normal position.:thumbsup:
Lee24h
29-03-2013, 10:59 AM
Any tips for if damage prevention that could be added when runningnthe configuration as 10 car finals make your cars rear end quite acident prone
RichyUK
29-03-2013, 03:37 PM
Any tips for if damage prevention that could be added when runningnthe configuration as 10 car finals make your cars rear end quite acident prone
Be faster than the the car in front :D
I know what you mean, it is a worry having them on the rear, much safer on the front, but its a risk you take. the bottoms are mounted pretty close to the wheels so theres a bit of protection there.
av4625
29-03-2013, 10:05 PM
Dont no y u guys worry about the shocks getting damaged, other manufacturers hav the shocks at the back with no problems, somebody would have to hit you pretty hard to damage them!
That's what I was thinking, the Losi can only be run this way. Just wish we could use the droop screw still.
AfroP
31-03-2013, 04:17 PM
That's what I was thinking, the Losi can only be run this way. Just wish we could use the droop screw still.
Drilling the holes on the back of the original arms will still allow the droop to be used.
Its an option
brooksy
31-03-2013, 06:30 PM
Ran mine with the shocks at the rear of the arms and the Dimec20 chassis yesterday at Broxtowe. Car was excellent even in the wet. Started to snow before my first race so I put BB greens on all round and I could go at speed into corners and the rear just held. I've got my first 2wd regional there next weekend and I'm going to leave it as is.
Only down side was my crap driving and i ended up breaking my gearbox casing believe it or not:woot:
AfroP
09-04-2013, 10:28 AM
ran mine with rear shocks and arms flipped on Sunday night on a slippy/carpeted youth center hall and it was aces.
back end felt far more planted than it usually does and I was able to give full acceleration on the slippy stuff without having to correct for loss of rear traction.
I'd highly recomend the switch
OneKiwi
09-04-2013, 12:16 PM
Ran mine with the shocks at the rear of the arms and the Dimec20 chassis yesterday at Broxtowe. Car was excellent even in the wet. Started to snow before my first race so I put BB greens on all round and I could go at speed into corners and the rear just held.
What setup were you running Brooksy, ditto AfroP
AfroP
09-04-2013, 12:35 PM
What setup were you running Brooksy, ditto AfroP
Front
Springs - dark red
Pistons - Kit
Oil - 30wt losi
Schuey yellow min spikes with medium foams
shocks mounted on outer hole on arms and mid hole on tower
Rear
Spring - Light green
Pistons - kit
Oil - 27.5wt losi
Schuey yellow mini spikes with medium foams
Shocks mounted on mid hole top and bottom
rear camber link has both spacers and mounted on 2nd hole from the outside on the hubs
No extra weight in the car at all, Dimec chassis and running ball diff
brooksy
09-04-2013, 02:33 PM
Ill post mine up later if I get chance. Ran it again at Broxtowe regional this weekend gone with same setup. First couple of races I had trouble with front end digging in too much,new old style staggers on front and part worn mini spikes on rear,but even so the back end didn't swing out. For the third race I put new mini spikes on the back and the car was mint. Put my best time in.
OneKiwi
09-04-2013, 06:00 PM
Thanks AfroP
Stock pistons? 6x 1.2 Front and 6x 1.3 rear ?? or have you plugged or drilled something.
Thats pretty similar to the setup I have but had trouble with the back end wanting to rotate..
But I had well worn spikes, so I have mounted up a new pair and will test again tomorrow
I had 4x1.3 and those oils
brooksy
09-04-2013, 08:38 PM
Setup for mine at a dry Broxtowe this weekend gone:-
Front
Kit Springs
Pistons - 4x1.2mm
Oil - Losi 35wt
Tyres - Shuey yellow staggers
Shocks - Outer hole on top and outer hole on bottom
Rear
Kit springs
Pistons - 6x1.2mm
Oil - Losi 30wt
Tyres - Shuey yellow mini spikes
Shocks - Center top and center bottom
Phill
danny the elfman
12-04-2013, 02:14 PM
Hey guys. There seems to be a lot of information in this thread and some of it contradicting to others. Could someone just answer these questions for me?
1) Where do I need to drill holes, is it better with the arms flipped or drilled?
2) Does this work for both DIMEC and standard chassis', and does it work best on a grippy or low traction surface?
3) What are the exact steps In need to follow to do this?
Thanks
Dan
brooksy
12-04-2013, 02:48 PM
I've drilled the holes rather than flip the arms. All I did was measure from center of hinge pin hole to center of middle hole and drill where appropriate on the back.
I would think it would have the same effect on both chassis'.(not 100% certain though)
Not tried it on low grip yet,just high grip astro.
Phill.
OneKiwi
12-04-2013, 05:59 PM
I tried it on the +8 chassis, I flipped the arms at first then thought that I might want to try it back to back with the normal postítion, which flipping the arms with the shims and piviot balls out at the track isn't as easy as just drilling and then just swapping the shocks over.
I had troubles with the buggy wanting to swap ends all the time, but discovered that my rear shocks where way off and I put on some new rear tires.
That helped a lot and like a previous poster said I can get on power earlier out of corners.
If the weather holds up for sunday Ill give the stock chassis with rear shocks a go
NeilRalph77
08-05-2013, 07:11 AM
Ill give the stock chassis with rear shocks a go
And the results were?
OneKiwi
08-05-2013, 08:28 AM
Works well but I find the weight of the stock chassis makes it feel a bit lazy as I have to have heavier shocks
I like the plastic +8 for weight then I can go lighter shocks. It feels a little more nimble.
dbizzle5
08-05-2013, 05:43 PM
Anyone got any pics of how to do this on the 410?
OneKiwi
11-07-2013, 10:43 AM
Heres one, I flipped the arms and redrilled for the ARB. Didn't get to try it more than a couple of packs on turf, before I sold the 410 but it felt good.
http://i30.photobucket.com/albums/c338/simonandhanna/IMG_20130618_130027.jpg
Loheswaran
22-10-2013, 07:25 AM
Now I am no great shakes, at driving and hadn't driven for over 7 months. I tried this mod out (shocks to the rear) with a longer chassis.
I found that the rear end was a bit heavy and sluggish - hard to describe. Should I try lighter oils - will that do the trick?
Dino_D
22-10-2013, 06:29 PM
Now I am no great shakes, at driving and hadn't driven for over 7 months. I tried this mod out (shocks to the rear) with a longer chassis.
I found that the rear end was a bit heavy and sluggish - hard to describe. Should I try lighter oils - will that do the trick?
I think you got too much roll
Adjust the roll center.
Try removing the spacers under the inner camber links.
Or use shorter links.
dex210Nick
26-10-2013, 11:50 AM
Has anybody know what exactly this mod changes? I've seen so many people do this and say it's great, but nobody explains why.
with the arms swept forward for toe angle, flipping the shock holes to the backside would actually push them further out from the chassis slightly compared to normal. That would effectively be the same as a slightly stiffer spring. It seems like most people extend their wheelbase when they do this. Is the difference in handling just the result of the change in wheelbase?
I just weighed one of my shocks and it came out to 20g. I think moving a total of 40g to the very back of the car might make the biggest change. I'll have to try it and see how it comes out on the scales. I could always use more weight over the rear in my car.
rcjunky
28-10-2013, 04:50 AM
I think it has to do with the weight and where the weight is. It gives more of a pengelum effect similar to rear motor, to a lesser extent.
flanny
30-10-2013, 02:45 PM
is there any real gain with this modification on a high bite carpet track or is it more aimed at clay or Astro tracks
Legacy555
30-10-2013, 03:01 PM
Definite gain.
It increases traction or lets you run less rear pack and maintain the traction you have.
Downside is that you have hung more weight both beyond the rear axle and more importantly away from the polar centre of the car.
Origineelreclamebord
30-10-2013, 03:13 PM
is there any real gain with this modification on a high bite carpet track or is it more aimed at clay or Astro tracks
http://www.teamxray.com/xb4/images/slider_2_1.jpg
http://www.teamxray.com/xb4/images/slider_2_2.jpg
This is what Xray recommend on their XB4. I know it's neither a 2WD nor a TD, but apparently it's for high traction. My guess is that the rearward shock position would indeed add a little pendulum effect - which you don't really want/need on low-bite because the back end will 'always' try to step out, whereas on high-bite it might be preferable to have the rear end slide out that tiny bit (more) - much like you see in slow-mo shots from F1 cars - it helps the chassis point more towards the inside of the corner (increasing steering in a way) I think? :eh?:
flanny
30-10-2013, 08:01 PM
Write goin to have a go at this but getting mixed opinion am I better flipping or drilling that's the question???
mistkerl
13-11-2013, 07:01 PM
Hi Flanny,
i have drilled the holes today! Pics will follow!
'caster master
13-11-2013, 07:15 PM
I think the main effect of putting the shocks in front of or behind the arm is the way the arm twists when the suspension is in use.
mrspeedy
13-11-2013, 08:10 PM
plus the fact that your putting 2 rather heavy components of the car quite a lot further back .. !!
I just flipped the arms and all on mine .. seems to work on sandy astro rather nicely .. also went back up to kit rear springs instead of the lt greens ... best my 'Rangos ever been .. and on kit chassis too :p
how about the DESC 210 anyone done the shock mod
mistkerl
14-11-2013, 07:48 AM
I will post a few Pics from my DESC210R with flipped arms later.
Danosborne6661
14-11-2013, 09:19 AM
how about the DESC 210 anyone done the shock mod
I've flipped mine Neal. You just have to dremmel the wishbone slightly on the inside to clear the diff outdrives.
mistkerl
15-11-2013, 08:28 AM
[/URL][URL="http://abload.de/image.php?img=img_2245tes6y.jpg"]http://abload.de/img/img_2245tes6y.jpg (http://abload.de/image.php?img=img_2245tes6y.jpg)
http://abload.de/img/img_22469qsgk.jpg (http://abload.de/image.php?img=img_22469qsgk.jpg)
http://abload.de/img/img_2247tcskb.jpg (http://abload.de/image.php?img=img_2247tcskb.jpg)
http://abload.de/img/img_2248umst5.jpg (http://abload.de/image.php?img=img_2248umst5.jpg)
http://abload.de/img/img_22495ss9x.jpg (http://abload.de/image.php?img=img_22495ss9x.jpg)
http://abload.de/img/img_2250g8sse.jpg (http://abload.de/image.php?img=img_2250g8sse.jpg)
Flip arms is much better than drill holes (DEX210). I added 4mm shims so that the damper is straight (see picture). If you flip the arms of your DESC210R you need to dremel some plastic. Danosborne6661 (http://www.oople.com/forums/member.php?u=1208) already say that.
Hi
I was asking about doing it on the SCT and what differance it makes to the handling and lap times.
Regards
CARB
mistkerl
17-11-2013, 06:29 PM
DESC210R
http://abload.de/thumb/img_2261kdsdw.jpg (http://abload.de/image.php?img=img_2261kdsdw.jpg) http://abload.de/thumb/img_2260nisxt.jpg (http://abload.de/image.php?img=img_2260nisxt.jpg) http://abload.de/thumb/img_2262y8s1g.jpg (http://abload.de/image.php?img=img_2262y8s1g.jpg) http://abload.de/thumb/img_22599vsrd.jpg (http://abload.de/image.php?img=img_22599vsrd.jpg)
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.