How to fill losi shocks properly

[Team No Idea]

Bonjour! my good lady's Academy has been fitted with old losi shocks, is there a correct way of filling them with oil? I have given it a try but i seem to be getting loads of air inside and loads of oil on the floor!:eh?:

[ashleyb4]

Fill then up to the bottom of the thread insert the cartridge with the shaft all the way in tighten it up a few turns then pull the shaft out push it back in again and tighten up. That should do the trick.

A

[ben]

Hmm my way is different to ashleys. I fill right to the top with shock oil, then i put the piston in with the cartridge to the top of the shock shaft. Next i screw the cartridge in 1 turn and then pull the shock shaft slowly out then slowly back in again and tighten the cartridge up with the shock shaft stull pushed right. Smooooth shocksssss. Id reccomend the nortech whities 'o' rings aswell. These make your shocks alot smoother :thumbsup:

HTH

[Team No Idea]

Excellent, thanks, i'll give it a wee try. I knew i was doing something wrong when the shock shafts were sucking themselves back in to the shock bodies when fully tightened!!! D'oh!

[ben]

They should suck themselves in and out a little bit!!!

[Team No Idea]

Ah, ok, looks like ill be getting messy again tomorrow evening then.......... i may be there some time !!! lol
Thanks for you help:thumbsup:

[ben]

Thanks for you help:thumbsup:

Anytime :)

[ashleyb4]

Its the same way ben its just if you fill them to the top you are just waisting oil and making more of a mess as the cartridge fills the part of the shock body where the thread is.

A

[ben]

Its the same way ben its just if you fill them to the top you are just waisting oil and making more of a mess as the cartridge fills the part of the shock body where the thread is.

A

Sorry pro!

[Lee]

I think your both being homo`s, just fill the shock body to the threads, screw the cartridge in a few turns, push the piston all the way in and then tighten the cartridge, pump the shock a few times then push in all the way, the shock should rebound about 5mm.

As uncle ben would say, "perfect every time" :D

[ashleyb4]

Sorry pro!

Its ok ben aslong as you have learnt for next time. :p

A

[ben]

hahahaha i dont think i learnt anything

[Chris Doughty]

i put the piston/shaft/cartridge into mine with the piston fully extended so the cartridge is next to the ball cup and leave it like that while I tighten it

[Kopite]

i put the piston/shaft/cartridge into mine with the piston fully extended so the cartridge is next to the ball cup and leave it like that while I tighten it

that's how i do it too mate, i never overfill the dampers then

:thumbsup:

[Lee]

Similar to mine then chaps, in a way.

And screw the body onto the cartridge, not the other way round, ;)

[Wraggy]

that's how i do it too mate, i never overfill the dampers then

:thumbsup:
well you 2 clearly dont know what your talking about !!! you should listen to Ash & Ben who been driving for years :woot::woot:

[Chrislong]

I do it different again.... the OCD way :(



Fill the body up to about 1mm below threads.

Slide the cartridge up the shaft to the rodend.

Find the slot on the cartridge.

Hold the body at approx 45 degrees, put cartridge into body with slot upwards.

tighten by turning the body, keeping slot upwards - may have too much pressure at this point.

Pump the shaft like a mofo

loosen (keeping slot to top, 45 degrees) release oil, retighten with RPM tools.

Put on car.

[bigred5765]

i use the schlong way as well, works a treat.

[Chris Doughty]

I do it different again.... the OCD way :(



Fill the body up to about 1mm below threads.

Slide the cartridge up the shaft to the rodend.

Find the slot on the cartridge.

Hold the body at approx 45 degrees, put cartridge into body with slot upwards.

tighten by turning the body, keeping slot upwards - may have too much pressure at this point.

Pump the shaft like a mofo

loosen (keeping slot to top, 45 degrees) release oil, retighten with RPM tools.

Put on car.

I agree with that

I also try and put the piston into the oil at as much angle as possible to minimise air trapped under it

[ben]

well you 2 clearly dont know what your talking about !!! you should listen to Ash & Ben who been driving for years :woot::woot:


hehehehe..... hmm i think its all your own preference how you fill your shocks. I really struggled to do associated shocks all the same. So drilled the shock caps for a bleed screw like the yokomo ones which made it alot easier for me to do them

[Kopite]

Slide the cartridge up the shaft to the rodend.


i must have issues, cos this sentence gave me a hard on :o

[bigred5765]

i must have issues, cos this sentence gave me a hard on :o

lol, do you have any relatives in the fictional town of Quahog:D
giggady giggady

[Lee]

No Carl, its fictional :woot:

[super__dan]

Schlong convinced me of his way, allows a little air in but am now agreed that's a good thing.

[Chrislong]

i must have issues, cos this sentence gave me a hard on :o

Im not sure whether to be worried or laugh, its more like a worried laugh. :D

[Stu]

I do it like the schlong,

fill with oil,
locate the slot,
pull the shaft up to the flange,
present your assembly to the hole,
screw in gently most of the way,
push the shaft in deep,
finish screwing,
mop up the inevitable mess.

[Kopite]

I do it like the schlong,

fill with oil,
locate the slot,
pull the shaft up to the flange,
present your assembly to the hole,
screw in gently most of the way,
push the shaft in deep,
finish screwing,
mop up the inevitable mess.

right, well now i've creamed myself :drool:

[Team No Idea]

LOl, cant do any of it for laughing at your replies:woot::thumbsup:

[Chrislong]

finish screwing,
mop up the inevitable mess.

..... don't use the curtains, unless you're in a hotel room.

[Lee]

I know someone who wiped himself on some birds curtains once, it turned out he left his wallet there and had to go back and ask for it later :woot:

[Stu]

wiped himself on some birds curtains

To be fair though her curtains should already have been messy.

[Chrislong]

As long as he didn't stand on the window sill to do it.

[Lee]

I think Stu means the beef curtains ;) :woot:

[Wraggy]

right, well now i've creamed myself :drool:
your missus cant be happy mate if thats all it takes .
still she gets an early night every time !!! :woot::woot:

[Kopite]

your missus cant be happy mate if thats all it takes .
still she gets an early night every time !!! :woot::woot:


she's usually asleep before i get cracking dude :woot:

[ben]

she's usually asleep before i get cracking dude :woot:

"cracking" the wot stan?:o

[Chrislong]

"cracking" the wot stan?:o

Its the sound of the mushroom stamp. :thumbsup:

[Lee]

I can just imagine your neighbours now stan, banging on the wall shouting

"can you keep it down building those shocks!"

[CLARKSON]

"cracking" the wot stan?:o

You boy, really need to get laid.

[c0sie]

Not only is this thread extremely helpfull (managed to build my Losi shocks perfectly thanks to all the advice!) but its also probably the funniest read in agggggges!! lol

[DaHomie]

Totally agree, you guys are not only brilliant shock builders you are as well hilarious!!

Keep it up please, both the excellent tips and your craziness ;-)

//DaHomie

Not only is this thread extremely helpfull (managed to build my Losi shocks perfectly thanks to all the advice!) but its also probably the funniest read in agggggges!! lol