View Full Version : Show us your Tamiya TRF 201 XR.
xfactor
02-08-2013, 02:25 PM
Hi all,
Thought it would be nice to start a new thread for the new tamiya 201 xr, so here it is.
My new tamiya 201 xr with tamiya big bores.Any question please ask Enjoy :thumbsup:
andoiwebb
02-08-2013, 02:35 PM
Looks great, xfactor! You could make it look even better by adding a Vega Gen3 conversion!
Shame the spring retainers are a different shade of blue :(
Aussie Top Force
03-08-2013, 07:20 AM
Well done Xfactor! Very neat build and wiring. Is that a shorty pack with the receiver positioned under the rear bulkhead?
Thinking I might order the BB's for my 501X and 201+Exotec 8mm. But I'm very tempted to get the XR! I might wait until the mid mount conversion is available a build a mid mount XR from scratch??? Thus I'll have a rear motor and mid motor to play with.
As the tracks over here are sugared more and more, grip is no loner an issue on our clay tracks and mid mount appears to be where the trend is going.:thumbsup:
Thanks for the pictures!
xfactor
03-08-2013, 08:53 PM
Hi David,
Yes shortie pack with receiver and transponder at rear under bulkhead.I did this as not to kink the wires off the speedo and gain more air around the speedo by fitting the speedo on the battery bar due to no fan.
Mark.
Johnny Pedersen
12-08-2013, 08:02 PM
Hi all,
Here are my car :-)
Origineelreclamebord
12-08-2013, 09:51 PM
Hi all,
Here are my car :-)
That looks even more like a Vega than I thought! That said, it does look pretty neat, I wasn't expecting Tamiya to sell the conversion with an alu gearbox. I take it Tamiya anodized the casing, or did you have it done yourself? :)
Aussie Top Force
13-08-2013, 09:52 AM
Wow, looks nice! Where did you source the rear conversion from? Stellamodels hasn't released them yet.
Johnny Pedersen
13-08-2013, 03:21 PM
The conversion kit have arrived in Denmark, together with the new racing steering set :-)
Johnny Pedersen
13-08-2013, 03:23 PM
The gearbox are blue from Tamiya, it is standard :-) :)
andoiwebb
13-08-2013, 06:39 PM
Nice Vega copy, though the Vega conversion looks better.
trowta
14-08-2013, 12:32 AM
The conversion kit have arrived in Denmark, together with the new racing steering set :-)
do they ship international? if so do they have a website???
Fredrik Emilsson
14-08-2013, 10:13 AM
Nice Vega copy, though the Vega conversion looks better.
True, gearbox looks very similar to Vega. Would´nt say copy, but very similar.
Chassi looks very similar to 22.
Front similar to B4.
But most buggies have borrowed ideas and design from other models.
Would very much like to see some more "twists" from Tamiya.
But performance is of course the most important thing with TRF cars.
Origineelreclamebord
14-08-2013, 10:47 AM
Nice Vega copy, though the Vega conversion looks better.
That's only down to the badly shaped sidepods - if they would merge into the front bulkead and motor guard/rear bulkhead to make a smooth tub shape it would look better than the Vega :)
Racecrafter
15-08-2013, 02:44 AM
That's only down to the badly shaped sidepods - if they would merge into the front bulkead and motor guard/rear bulkhead to make a smooth tub shape it would look better than the Vega :)
Side guards were designed not to connect to the front nose piece or the rear bulkhead to aid in flex-tuning. :)
Origineelreclamebord
15-08-2013, 09:14 AM
Side guards were designed not to connect to the front nose piece or the rear bulkhead to aid in flex-tuning. :)
Imo it is just to cut costs. They could easily aid flex with bigger sidepods, look at the Xray XB4: It has a whole tub you can tighten onto the car in many configurations to adjust flex. So simply said, they could connect the sidepod in the front and rear, and add extra holes throughout the length of the sidepod to adjust rigidity (even specifically to a certain area of the car)...
So nice that the feature is on there, and I understand the TRF201's small market share doesn't give the best bargaining position to the director's board to increase the ambition of the project to a new kit, moulded sidepods or whatever... but in all honesty with Tamiya's rich history of attention to detail, they should know better :)
Aussie Top Force
15-08-2013, 09:55 AM
Imo it is just to cut costs. They could easily aid flex with bigger sidepods, look at the Xray XB4: It has a whole tub you can tighten onto the car in many configurations to adjust flex. So simply said, they could connect the sidepod in the front and rear, and add extra holes throughout the length of the sidepod to adjust rigidity (even specifically to a certain area of the car)...
So nice that the feature is on there, and I understand the TRF201's small market share doesn't give the best bargaining position to the director's board to increase the ambition of the project to a new kit, moulded sidepods or whatever... but in all honesty with Tamiya's rich history of attention to detail, they should know better :)
TRF Cars don't have a big market share (Globally) because they don't have a top ten USA driver. Lee Martin is good and certainly a contender for top 10 at the worlds, but they need a good USA based driver to mix up the AE, TLR and Kyosho drivers. Tamiya is a big company and makes many model products, so budget shouldn't be an issue. The cars have what it takes, all they need a US based driver to take them there! Kyosho have.
taomo
15-08-2013, 11:45 AM
Hi,
some pics of my TRF201XR. It is not finished yet because I am thinking about the saddle LiPos position before the soldering process. My local track is very similar than the Valladolid Euros 2013. What do you think? "stick" position would work better than "saddle" (I have the #54440 TRF201 Suspension Weight Block (5-Deg.)).
Johnny Pedersen, I want the new alu steering set, where did you buy it?
Best regards
patez
15-08-2013, 04:35 PM
Taomo, i tried saddle configuration without any extra weight and it felt very nose heavy on clay. then again there was lot of turf lookin parts in vallodid.. its not a rear traction machine like the old 201 imho.
D.A.R.C 1
15-08-2013, 05:00 PM
That's only down to the badly shaped sidepods - if they would merge into the front bulkead and motor guard/rear bulkhead to make a smooth tub shape it would look better than the Vega :)
I totally disagree with statement above
If it had a smooth tub shape etc like you say then it would look just like a Vega
No better no worse. The same.
taomo
15-08-2013, 08:21 PM
Taomo, i tried saddle configuration without any extra weight and it felt very nose heavy on clay. then again there was lot of turf lookin parts in vallodid.. its not a rear traction machine like the old 201 imho.
Thanks patez!
Origineelreclamebord
15-08-2013, 08:29 PM
I totally disagree with statement above
If it had a smooth tub shape etc like you say then it would look just like a Vega
No better no worse. The same.
I'm not saying it should consist of one machined piece - More like the 'Red Workshop' TRF201 that Lee Martin was driving at the 2013 Cactus Classic:
http://www.petitrc.com/setup/teamxtreme/setupvegaelitetrf201x/TRF201XVega_LeeMartin_CactusClassic2013031417/
...but with more overlap between front nose piece and sidepods :)
@patez: I think rear traction isn't the flavour of the month, but the priority has gone to increasing steering (even on RM cars). The chassis should prove stiffer at the back compared to the plastic T-plate of the original tub, so that in combination with a battery that's further forward should make quite a difference... So does it actually have more steering (aside from feeling more nose heavy)?
Has anyone driven the XM yet? And even better perhaps, has anyone been able to compare it with a Vega chassis? I'm curious to see how they compare because I've been hoping for Tamiya to do something with a mid-motor layout - I'd say a plate chassis like Tamiya's might be more flexible and easier to adjust to lower bite surfaces... but of course those things are best felt by someone on the track! :)
Racecrafter
15-08-2013, 08:34 PM
Imo it is just to cut costs. They could easily aid flex with bigger sidepods, look at the Xray XB4: It has a whole tub you can tighten onto the car in many configurations to adjust flex. So simply said, they could connect the sidepod in the front and rear, and add extra holes throughout the length of the sidepod to adjust rigidity (even specifically to a certain area of the car)...
So nice that the feature is on there, and I understand the TRF201's small market share doesn't give the best bargaining position to the director's board to increase the ambition of the project to a new kit, moulded sidepods or whatever... but in all honesty with Tamiya's rich history of attention to detail, they should know better :)
I want to first say that I'm not arguing just pointing out the intent of the design. You state it was to cut costs. Have you seen the side pods on the XR? They are machined out of an Acetal derivative which is expensive. There are 3 holes per side plus the inner 2 on the front which are plenty enough to tune with. To be honest I don't care for the "look" either but that is how it was designed.
Origineelreclamebord
15-08-2013, 08:49 PM
I want to first say that I'm not arguing just pointing out the intent of the design. You state it was to cut costs. Have you seen the side pods on the XR? They are machined out of an Acetal derivative which is expensive. There are 3 holes per side plus the inner 2 on the front which are plenty enough to tune with. To be honest I don't care for the "look" either but that is how it was designed.
It is indeed expensive - I know the price of that conversion isn't without reason. But the cost of a mould for two parts that size is considerable too. When you know that not everyone owning a TRF will even convert the car, machining is quite a sensible option I think: They could do it because they're expecting demand to be too limited to justify the production of a mould and/or this allows them to produce small batches without the need of much initial investment... so if the demand is higher than expected they can just machine another batch. I know Tamiya is a huge brand, but in these times no RC company will accept to lose money on any released model in their range - TRF included.
That said, I do appreciate the decision to go for machining from a quality perspective. With low production runs you can consider a cheap mould, lesser material quality or (too) short cycle times resulting in horrible parts... But on that front Tamiya always seem to make sure everything's well sorted! :)
Racecrafter
15-08-2013, 08:50 PM
I'm not saying it should consist of one machined piece - More like the 'Red Workshop' TRF201 that Lee Martin was driving at the 2013 Cactus Classic:
http://www.petitrc.com/setup/teamxtreme/setupvegaelitetrf201x/TRF201XVega_LeeMartin_CactusClassic2013031417/
...but with more overlap between front nose piece and sidepods :)
@patez: I think rear traction isn't the flavour of the month, but the priority has gone to increasing steering (even on RM cars). The chassis should prove stiffer at the back compared to the plastic T-plate of the original tub, so that in combination with a battery that's further forward should make quite a difference... So does it actually have more steering (aside from feeling more nose heavy)?
Has anyone driven the XM yet? And even better perhaps, has anyone been able to compare it with a Vega chassis? I'm curious to see how they compare because I've been hoping for Tamiya to do something with a mid-motor layout - I'd say a plate chassis like Tamiya's might be more flexible and easier to adjust to lower bite surfaces... but of course those things are best felt by someone on the track! :)
I agree that Red's car is gorgeous and the XR should have been produced in that way. The XR set up with the HRC shim under the trans and rear mount make the car very edgy. Once it's removed and the front shim replaced with a plastic 1mm shim the car is more stable. The XR has a ton more steering from front grip. The length in the chassis (and the added weight of it) make this happen. Adding the 30g weighted bulkhead adds to this even more. The rear is looser than the plastic chassis which is due to the lack of flex (no T-plate) and the length/ front weight.
TRX450RACER174
20-08-2013, 07:45 PM
My 201XR
http://i276.photobucket.com/albums/kk10/TRX450RACER174/04519661-FD95-4E97-B2D4-C7539624FEDC-10596-0000058C5114E925_zpsfb9fbf38.jpg
Aussie Top Force
23-08-2013, 11:33 AM
Curiosity killed this cat:lol: I ordered an XR kit and managed to find a brand new 201 kit on Ebay for a reasonable price. So I'm going to build up an XR from scratch rather than convert my existing 201.
Should be a good comparison. I already have some Big Bores on my 502X so can't wait to build it and get to the tracks!:thumbsup:
xfactor
23-08-2013, 03:45 PM
Top Aussie, do it do it do it :D
taomo
23-08-2013, 05:30 PM
It is not a bad idea Aussie Top Force!!!
kentech
28-08-2013, 09:28 AM
Posted some scans from Rc World magazine yesterday of Satoshi Maezumi's TRF201XR and TRF201XM including setups. All of them (5 pages) can be found here:
http://kentech.blogs.se/
I also have a complete new (NIB) TRF201 kit together with XR conversion kits + big bores for sale if anyone's interested:
http://www.oople.com/forums/showthread.php?t=134757
http://data9.blog.de/media/171/7205171_932bfa4410_o.jpeg
Here a Tamiya Japan magazine ad for the XR and XM:
http://data9.blog.de/media/162/7205162_5c3ead95c3_o.jpeg
Aussie Top Force
30-08-2013, 09:27 AM
I like the look of the midship car! Seems to be the way to go.
Will order the XM kit as soon as I can find one! Stella doesn't have them yet, and either does RCMart. TRF cars are hard to find in Aus so ordering from OS, and Ebay are my only options. Any body no an online store that has XM stocks?:confused:
t8rtot
31-08-2013, 04:28 PM
Now if they'd just bring an updated 511 to match.
Aussie Top Force
02-09-2013, 08:57 AM
Got my XR kit today from RC-Mart. It arrived as per the images. Not in a good way. Luckily the parts were untouched and all there as there was a rather large whole in the box, which was plugged by Aussie Post!
julius_makewar
02-09-2013, 10:10 AM
Hey Aussie,
I received my XR from RCMart today also (South Australia). The box was in much better condition than yours mate.
Cheers
Aussie Top Force
02-09-2013, 01:05 PM
Hey Aussie,
I received my XR from RCMart today also (South Australia). The box was in much better condition than yours mate.
Cheers
Good to know! Hopefully this was a one off! I ordered some extra parts as well. Luckily they were in the other end of the box, undamaged, however if they were at the end that was damaged, its likely they would have fallen out or have been damaged.
A lucky escape this time, all things considered! Stella Models packages much better and is similarly priced. Unfortunately for RC Mart, this one off trial will send me back to Stella.
julius_makewar
03-09-2013, 01:21 AM
I have purchased from RCMart a few times before without issue but they are a little slower than Stella and RCMushroom. I believe your packing issue to be a one off, in transit, incident.
Anyway, do you have a setup you are going to try on your XR? I am a little unsure regarding the rear suspension mount high and low setting. Is the included XR alloy suspension block raisers high position and the kit 201 plastic raisers used for normal/low position?
Cheers
Aussie Top Force
03-09-2013, 09:12 AM
I have purchased from RCMart a few times before without issue but they are a little slower than Stella and RCMushroom. I believe your packing issue to be a one off, in transit, incident.
Anyway, do you have a setup you are going to try on your XR? I am a little unsure regarding the rear suspension mount high and low setting. Is the included XR alloy suspension block raisers high position and the kit 201 plastic raisers used for normal/low position?
Cheers
RC Mart have agreed to give a $10 credit, which I think is reasonable in the circumstance, as none of the actual parts were damaged.
In respect of set up at the rear, I haven't figured out what I'm going to try as yet. I'm going to install the optional aluminium 3 degree suspension hangers. The question is are they a straight replacement for 'J1' and 'J5'?
I do know I am not running the 'J7' part on my TRF 201 LE with Exoctec +8 option.
I think I'll pull out the calipers and measure the thickness of the original T-plate and the XR chassis.
Anybody else have an answer?
trowta
05-09-2013, 12:25 AM
check out www.petitrc.com (http://www.petitrc.com) for all for questions regarding the rear suspension blocks and the like
regards
Tod TROWER
trowta
05-09-2013, 12:26 AM
I like the look of the midship car! Seems to be the way to go.
Will order the XM kit as soon as I can find one! Stella doesn't have them yet, and either does RCMart. TRF cars are hard to find in Aus so ordering from OS, and Ebay are my only options. Any body no an online store that has XM stocks?:confused:
try etamiya they had them listed on September 4 for delivery immediately
taomo
07-09-2013, 02:44 PM
My 201XR in a rainy day :lol:
Now we can buy the new alu steering set and 201XM in stella (and other stuff)
Best regards
Aussie Top Force
08-09-2013, 03:07 AM
Some pictures of my new built XR. XM conversion and electrics in the mail. Will do some back to back runs between new and old chassis before deciding on whether to buy another XR and covert the original as well, i.e., one XR and one XM, ready to run?
Aussie Top Force
09-09-2013, 09:31 AM
And the Paint Job. Decided to try some new colours. Looks pretty bright in sun light!
stevenich
11-09-2013, 12:18 AM
https://www.dropbox.com/s/6x95595eli7c7fl/2013-09-10%2018.19.10.jpg
Sumimasen
13-09-2013, 05:01 PM
First post!
Here is my TRF 201 before the XR conversion:
https://dl.dropboxusercontent.com/u/45937343/Tamiya_TRF_201_01.jpg
And part way through:
https://dl.dropboxusercontent.com/u/45937343/TRF201_XR.jpg
I'll post up finished pics once it's done. :-)
xfactor
13-09-2013, 09:22 PM
https://www.dropbox.com/s/6x95595eli7c7fl/2013-09-10%2018.19.10.jpg
Shocks in front of rear tower,cant see anything else different,whats the reason for fitting them in front of rear tower :confused:
stevenich
14-09-2013, 10:42 PM
Yes, Shocks on the front side. With the arms swapped the shock are at a terrible angle if mounted to the rear of the shock tower. To fix it requires 6-8mm spacer between lower shock eyelet and rear arm. That extra leverage looked fragile. I'll test and provide feedback.
Aussie Top Force
14-09-2013, 11:28 PM
Yes, Shocks on the front side. With the arms swapped the shock are at a terrible angle if mounted to the rear of the shock tower. To fix it requires 6-8mm spacer between lower shock eyelet and rear arm. That extra leverage looked fragile. I'll test and provide feedback.
Why swap the arms? This would only shorten the wheel base. Is it recommended by the instructions? I'm waiting for my XM from Stella.
xfactor
15-09-2013, 08:16 PM
Ok, i had the same problem with the tamiya vega, rear wishbones are reversed L goes on R,R goes on left with the sweep going towards the front of the car,what we do aswell is take 2mm off the wishbone (rear side) when fitted and put a 2mm washer to the (front side) of the wishbone this is for extra clearance off the corner of the chassis. Then i have fitted a 3mm washer at the bottom of the shock so as to give a better angle of the shock where it screws into the wishbone.
This maybe the same for the XM, but not sure as not got the XM as yet but try the above it may help.
Aussie Top Force
16-09-2013, 08:31 AM
The XM Conversion turned up today. The instructions suggest reversing the rear arms (left to right and visa versa) for tracks with lower traction.
Now I have a dilema. Run the car in rear motor configuration as built, or convert to XM before running:confused:
A good dilemma to have I guess! I've never run a mid motor 2wd so I think I'll covert for maiden run, plus the XM TRF Blue parts look the goods!:thumbsup:
stevenich
23-09-2013, 06:05 PM
Delete
Aussie Top Force
05-10-2013, 07:36 AM
Some pictures of my TRF 201 XM. Completed it today. Felt very neutral on the practice run (driveway/street). Can't wait to get it to the track:woot:
Hi, this is my TRF 201 XM/XR. I bought this package from Kentech. (Thx for the clean and fast sale btw) :thumbsup:
I ve got a new Proline Phantom body coming in next week also.:p
Probably going to build a lil' diff from what it is now as ESC needs a new spot.
I drove a TLR22 before this one and struggled with it. Not finding good balance driving it. Too tiny to build all elecs into. This TRF is much ez'er to find good setup and much better handling imo.
http://imageshack.us/a/img850/8381/s3ge.jpg
http://imageshack.us/a/img534/1355/3izh.jpg
fastfred
02-01-2014, 09:42 PM
Hello Everybody
In 2012 I raced the TRF 201 and replaced it with TLR22 to keep up with competition.
Unfortunately the 22 is a diva on low grip tracks or I am just not able to get a good setup... :confused: :confused:
As I love Tamiya, and due to the updates (BB shocks and XR Chassis), I decided to go for XR in 2014.
I still have all spares and ordered a new kit as well as all upgrades except the Aluminum steering.
For sure I will post a pic as soon as everything arrives.
There is only one question that is still in my mind.
Are there any rumors on a successor?
Gerrit
Origineelreclamebord
02-01-2014, 10:08 PM
Gerrit, I'm sure the 201XR will be a lovely car, but little setups are available so it may be hard to find a truly good setup for that...
Re- your TLR22, have you tried to replicate the setups from Wesley van Helmond? I drove his 22 and his 22 2.0 and it is amazing on low grip using mid-motor! I'm just saying: it may be worth a shot :)
Aussie Top Force
03-01-2014, 12:33 AM
My first run of the 201 XM was a day of chasing rear end grip on very dusty track! I had some success, but the track kept going away as well. I the end I swapped to my rear drive 201 LE with +8 Exotec conversion. It was more consistent.
That particular track is usually very grippy, but a think the lack of rain and high tempteratures was causing it to dry out and break up.
But thats why having a rear motor and mid motor 2wd is a good option! No need to rebuild the rear of the car to suit the track!
In time, when the track is in better condition I'll be able to tune the XM. One thing a I did do which helped was to move the top shock mounts front and rear inboard. Next time I'll play more with spring rates and role centre and rear toe. I've just purchased the XA mount for 3.5 degree to in. I may also try reversing the rear arms from side to side as per the instructions "for low grip tracks".
Most of all I need to work on my driving!
fastfred
03-01-2014, 05:58 AM
The 22 will be used as MM car for carpet tracks with a high amount of grip.
I will use it for this weekends Winterchamps 2014:
http://www.efac-hohenems.at/events/winterchamps/winterchamps-2014/
It is in German, sorry.
At this event Swiss Champion Patrick Hofer and former European Champion Hupo Hönigl will take part.
Under normal conditions (outdoor) I loose 7 seconds on Patrick :(
This might be the evidence that, no matter which car I drive, I need more practice.
But as a father, mountainbiker and with a job that wont release me for 10 hours a day, I just do not have enogh time.
Therefore I choose to drive XR just because it is a Tamiya and I like the look of it.
Sometimes it is just nice to build and tune a chassis and use it on the track
The XR for an outdoor clay track.
We have carpet jumps, but all in all it is low low low grip. We had blue grooves just one evening before a big race, after some rain all grip gone.
One of the more ambitious tracks around :-)
Aussie Top Force
04-01-2014, 12:03 AM
The 22 will be used as MM car for carpet tracks with a high amount of grip.
I will use it for this weekends Winterchamps 2014:
http://www.efac-hohenems.at/events/winterchamps/winterchamps-2014/
It is in German, sorry.
At this event Swiss Champion Patrick Hofer and former European Champion Hupo Hönigl will take part.
Under normal conditions (outdoor) I loose 7 seconds on Patrick :(
This might be the evidence that, no matter which car I drive, I need more practice.
But as a father, mountainbiker and with a job that wont release me for 10 hours a day, I just do not have enogh time.
Therefore I choose to drive XR just because it is a Tamiya and I like the look of it.
Sometimes it is just nice to build and tune a chassis and use it on the track
The XR for an outdoor clay track.
We have carpet jumps, but all in all it is low low low grip. We had blue grooves just one evening before a big race, after some rain all grip gone.
One of the more ambitious tracks around :-)
I'm pretty much in the same league. Father of 4 kids ranging from 4 to 11. The oldest has just started racing. With all the family commitments, work and no local track - the nearest is 1.5hours away I don't practice. Club racing is practice!
I race Tamiya for the same reason, love the quality and the fact that it looks great and is something different.
I'm glad the kids are interested, just more work in the pits though for me!
Firstly I'm loving the various 201's posted in this thread. I'm a die-hard Tamiya TRF fan so it's a shame the car isn't better supported by Tamiya.
I'm tempted to buy a new TRF201 to race at my local club as they are heavily discounted on the Tamiya-USA website at the moment.
However I also want to buy the XR chassis conversion (#42253) but they are still very expensive from Tamiya-USA. Does anyone know of alternative suppliers that still have stock of the XR conversion? All the obvious places seem to be out of stock.
Thanks :thumbsup:
Jamesk
27-01-2014, 03:08 PM
As for the XR and XM kits, i have been told by a farily reliable source that once the kits are sold there are no plans to make a new batch and the worlds verson will not be produced now.
Shame as iam impressed with the quality of the kits and the big bore shocks too
jK
Aussie Top Force
10-03-2014, 02:07 AM
I gave the XM another run for its money against some stiff competition yesterday, at the first "Sweep Cup", held at Castlehill, Sydney Australia.
Whilst, my driving still needs some work, the XM platform is not suitable for off road where traction is not consistently "high". I can see that it would be great on astro turf or manicured "sugared" track. It jumps well and cornered well at high speed (were grip was up) but, it had too much over steer where the track had low traction and it cost too much time. If you could stick to the "blue" line you could get a decent lap time, but trying to avoid other cars or make a move sent it sideways. They did sweep the track, which made things a lot better for Q3, but it was all too late by then.
So I'm going to covert it back to XR spec and see if I can drive it more consistently on a future visit to Castlehill. BTW TQ was a rear motor TLR 22.2.
I haven't given up on mid motor though. I keenly await the TRF 201 Mid Motor worlds kit, which moves the motor and batteries further back and sweeps the rear arms forward. Rear motor cars that were having success yesterday had more wait to the rear than the XM.
fastfred
22-03-2014, 06:01 PM
There it is:
https://lh4.googleusercontent.com/-D15yphnD6LI/Uy3Jf8a3oJI/AAAAAAAAGLo/nhtr9L66F8A/w511-h383-no/20140322_183147.jpg
https://lh6.googleusercontent.com/-_lKBchvKIRQ/Uy3JkruSUaI/AAAAAAAAGLw/4Hxj-3E6rdI/w287-h383-no/20140322_183251.jpg
What a beauty!!!
Hopped up with everything available except Titanium screws.
Look and feel is simply great.
Cheers
Gerrit
Aussie Top Force
23-03-2014, 01:45 AM
Although I've already placed XM pictures on this thread, after a couple of race meetings on our clay track, it became evident there simple isn't enough traction there to favour the mid motor configuration of the XM.
Thus, I've converted it back to XR configuration, but keeping the saddle pack battery configuration from the XM with the ESC behind the batteries.
The car feels well balanced, compared to the standards rear motor chassis with + 8 Exotek conversion. With a quick test run at home, the Exotec car had the tendency to wheel stand (a lot), whereas the XR with the saddle pack configuration does not.
The XR has every 201 option except aluminium steering and cooling pressure plates for the slipper.
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.