PDA

View Full Version : b44 cvd's

rob84
22-09-2008, 03:37 PM
hi there i have a b44 the steel cvds have rusted pretty bad. is there any way of stopping this? or can i replace them with shiny ones if so which ones ? cheers
ashleyb4
22-09-2008, 03:43 PM
Just soak them in some wd40.

A
Lee
22-09-2008, 03:48 PM
That wont stop the rust ash :lol:

All you can do mate is when its been wet give it a good clean and brush off and then a blast with WD or similar but the ket is to stop it from getting damp :thumbsup:
rob84
22-09-2008, 04:08 PM
is there none that you can get that wont rust?
ashleyb4
22-09-2008, 04:23 PM
That wont stop the rust ash :lol:

All you can do mate is when its been wet give it a good clean and brush off and then a blast with WD or similar but the ket is to stop it from getting damp :thumbsup:

No but it gets rid of it when they do rust.

A
Lee
22-09-2008, 04:34 PM
Are you sure it just makes the rust disappear? :confused:
nitrokillah
23-10-2008, 09:50 AM
hey...
dose any one know where I can find shiny CVD's ???
MIP don't do them for the b44 :cry:
Has any one tryed fitting the B4 CVDs ??
zaquiz
23-10-2008, 02:22 PM
We talked about this in a thread only some days ago.

http://www.oople.com/forums/showthread.php?t=15157
Bungleaio
23-10-2008, 03:26 PM
We talked about this in a thread only some days ago.

http://www.oople.com/forums/showthread.php?t=15157

Thats about the wishbones not the drive shafts
enfieldbanana
24-10-2008, 10:27 AM
Hey,

Don't think the B4 and B44 CVD's are the same. They have different part numbers:

AS9599: B4 CVD's

AS9754: B44 Rear CVD's

AS9749: B44 Front CVD's

Anybody know where you can get hold of a set of Lunsford ti turnbuckels and hinge pins?

Andy
Mike Hudson
24-10-2008, 10:45 AM
dms-racing should have the lunsford turnbuckles its the b4 6 piece set that you want I think
Richard Lowe
24-10-2008, 11:21 AM
JConcepts do shiny CVD's for the BJ4 which will be a direct fit for the B44 :)
ben
24-10-2008, 11:28 AM
JConcepts do shiny CVD's for the BJ4 which will be a direct fit for the B44 :)

Are you sure on that rich? Or do you mean the whole cvd assembly?
Richard Lowe
24-10-2008, 12:23 PM
The whole driveshaft Ben :)
Mike Hudson
24-10-2008, 12:25 PM
JConcepts do shiny CVD's for the BJ4 which will be a direct fit for the B44 :)
only problem is if you have to use the stub axles from the jc cvds which i have seen a staggering amount of them snap and arn't cheap! :thumbdown: i know 2 people on this thread have broken plenty ;):woot:
ben
24-10-2008, 12:27 PM
Must of just had a few bad batches :woot:
Richard Lowe
24-10-2008, 12:48 PM
only problem is if you have to use the stub axles from the jc cvds which i have seen a staggering amount of them snap and arn't cheap! :thumbdown: i know 2 people on this thread have broken plenty ;):woot:
I think though 99% of the breakages though have been Ben's :woot:
ben
24-10-2008, 12:49 PM
Do i get a prize for breaking the most :confused: 8!!:woot: ANIMAL!!!!
Richard Lowe
24-10-2008, 12:52 PM
Manimal!

How many cat diff outdrives have you done now Ben, have you got into double figures yet?!