View Full Version : XX4 steering bellcrank
matthewjtovey
23-07-2014, 09:21 AM
Hi,
Was running my xx4 at the weekend and the bellcrank arm slipped on an impact. Its started to flatten a few of the splines. Is it a complete write off or can it be salvaged? I've seen how people use longer bolts and washers to stop it happening but saw them too late!
If I need a new one where can I get one from? Any other tips to stop it happening?
Thanks for your help.
Matt
Oscar
23-07-2014, 09:01 PM
LOSA1550 I think is still available.
I was lucky enough a few years back to get a full alloy bellcrank setup, but prior to that had ran the drive pin mod. Essentially you drill from the top down and insert a steel pin (similar to the ones used on the rear axles which drive the wheels), this plus a smidge of superglue helps stop the arm slipping on the splines ;)
Explained here http://www.petitrc.com/setup/losi/setupdoublex4we/XX4WE_OlivierLanglet_SteeringBellcrankModification/
matthewjtovey
23-07-2014, 09:28 PM
LOSA1550 I think is still available.
I was lucky enough a few years back to get a full alloy bellcrank setup, but prior to that had ran the drive pin mod. Essentially you drill from the top down and insert a steel pin (similar to the ones used on the rear axles which drive the wheels), this plus a smidge of superglue helps stop the arm slipping on the splines ;)
Explained here http://www.petitrc.com/setup/losi/setupdoublex4we/XX4WE_OlivierLanglet_SteeringBellcrankModification/
Thanks for the info. Will have a good look for the parts and at that mod.
Incidentally, where did you get the alloy setup from?
Thanks
Origineelreclamebord
24-07-2014, 06:26 AM
If you really can't find a replacement, might it be an option to 3D print the parts and use a hex mounting instead of a spline system? :) There are surprisingly strong materials that might be strong enough (though it would be practical to add a little flesh just to be safe), and looking at the size of the part it wouldn't cost a fortune either.
PS: Also, could it be worth looking into the 22-4's steering bellcranks despite the fact there might be fit issues with metric parts on non-metric car...
matthewjtovey
24-07-2014, 07:24 AM
If you really can't find a replacement, might it be an option to 3D print the parts and use a hex mounting instead of a spline system? :) There are surprisingly strong materials that might be strong enough (though it would be practical to add a little flesh just to be safe), and looking at the size of the part it wouldn't cost a fortune either.
PS: Also, could it be worth looking into the 22-4's steering bellcranks despite the fact there might be fit issues with metric parts on non-metric car...
Thanks.
That's interesting about 3D printing, that would never have crossed my mind to do that!
I did wonder about the 22-4 or other losi belcranks, has anyone tried it? And got it to work more specifically!
Oscar
24-07-2014, 09:37 PM
The alloy ones I have came from the USA, advertised as a street weapon item. I bought the last 2 available and fitted one with just a very minor modification.
Sorry but the spare one isn't for sale even if you chuck in your Grandma, 10% of the Brinx Matt bootie and a gallon of Ardmore single malt :p
matthewjtovey
24-07-2014, 10:11 PM
The alloy ones I have came from the USA, advertised as a street weapon item. I bought the last 2 available and fitted one with just a very minor modification.
Sorry but the spare one isn't for sale even if you chuck in your Grandma, 10% of the Brinx Matt bootie and a gallon of Ardmore single malt :p
Ha! Fair enough! That was going to be my next question!
I've just had a look for street weapon alloy versions and the only one I found was this, would this work with some modding? Doesn't look likely to me but hey!
D20MCK
25-07-2014, 08:33 PM
That's not for a xx4, looks like it's from a xxx4/xxxS.
I might have a new spare bellcrank for the xx4
matthewjtovey
25-07-2014, 09:03 PM
That's not for a xx4, looks like it's from a xxx4/xxxS.
I might have a new spare bellcrank for the xx4
I thought the same but it's advertised as for the street weapon...strange isn't it!
Oh, how much for it?
Has anyone got a 22-4 to see whether the bellcrank can be modded from that? I know it's metric but worth a look!
D20MCK
25-07-2014, 09:11 PM
I've got a 22-4 I'll have a look to see if the parts fit each other
matthewjtovey
25-07-2014, 09:15 PM
I've got a 22-4 I'll have a look to see if the parts fit each other
Awesome thanks. And if not if you think there is a work around.
Cheers.
D20MCK
26-07-2014, 08:49 PM
I've looked and I don't have one spare bellcrank but the 22-4 part looks like it will fit.
matthewjtovey
26-07-2014, 09:38 PM
I've looked and I don't have one spare bellcrank but the 22-4 part looks like it will fit.
Thanks for looking!
If the 22-4 one does fit that is great, can anyone else confirm this? Just to be sure!
Oscar
26-07-2014, 10:52 PM
That's not for a xx4, looks like it's from a xxx4/xxxS.
That is the same as the ones I have, albeit a different colour. With just a few mod's this will fit ;)
matthewjtovey
27-07-2014, 12:32 PM
That is same as the ones I have, albeit a different colour. With just a few mod's this will fit ;)
Ah OK thanks, that's interesting!
So could go that route, though am still interested in the 22-4 one. I've checked the parts and the bearings it goes into and I reckon with a little bit material taken off so it fits in the xx4 bearing it could be a goer.
Does that look right to you guys?
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.