x-6 gearing help

[pizzaman]

hi, could some one please tell the correct pinion to use with a 78 spur. im using lrp sphere comp with x11 6.5 bonded and the 4 gear x-6 tranny.
i would rather get longer run times than over heat motor or speedo
cheers

[JustARcFan]

22 would be ok.

[Body Paint]

That sounds a bit big for a 6.5 Bonded, isn't it?

[JustARcFan]

Depends a bit on the track but a 22 or 21 would do it. Best you can do is test it and feel how hot the motor is after a run.

[bigred5765]

that is to big on a bonded rotor, we ran them all last year i would say 20 ish.

[burgie]

is a 22 too big? really?

i was running my x11 5.5 bonded on 23....anything less than that an it just sounded like it was revving it's tits off without going anywhere.

[bigred5765]

well not really to big but the guys asked for run time not speed,but 23 on a 5.5 is just plain crazy lol

[super__dan]

I agree, start lower and work up than overheat it and then gear down.

[burgie]

I agree, start lower and work up than overheat it and then gear down.

that's the ACE thing though, mine doesn't overheat on a 23, it runs cooler than it did between 20 - 22 :thumbsup:

[JustARcFan]

It all depends on the track.

I would start with a 20, check how hot the motor is and maybe gear up a bit afterwards.

[Mike Hudson]

20t should be just right :thumbsup:

[Lee]

What diameter are your rear tyres?

[pizzaman]

What diameter are your rear tyres?

3.2 ,3.3

[Lee]

Well after taking the tyre diameter into account and I assume you will either be running on astro/dirt or indoor where there is very low rolling resistance, I would probably start with a 20 tooth pinion and see how it goes from there :thumbsup:

[pizzaman]

thanks to all the quick replys 20/78 will be on for sundays racing.
cheers

[bigred5765]

What diameter are your rear tyres?


your such a tc bod lmao:thumbsup:

[Body Paint]

I beleive that if you calculate the rolling mass and take into account the moment of inertia, then divide that by the square root of pythagaris's theorum, that unless you actually knew the size of the tyres and the drag coefficient of said tyre that you would not be able to come to the same conclusion as everyone else, that the correct gear ratio for a 6.5 bonded is 20/78.... congratulations Lee... go to the top of the class :woot:

[Big E]

Lee that is a sad comment, I thought we had flushed that TC stuff out of you :D

I used to run a 21/81 on a 6.5 bonded so I would think 20/78 would be about right to start.

With sintered (12.5mm) I run 22/78.

I would recommend getting a sintered 12.5mm rotor as well as they run much cooler than with the bonded rotors

[Lee]

I do have the odd relapse.


My name is Lee and i have been TC free for 18 months :thumbsup::lol:

[bigred5765]

the whole room stands up and says, well done lee lmfao.

touring car anonymous

[usafaircrew]

I run a 23/78 here in the states with no issues. I run a 6.5 Novak. It is super quick. Sometimes I even wheelie my X-6:thumbsup:

[Body Paint]

USAFAIRCREW: The Novak is most likely running a Sintered rotor, in which case 23/78 is bang on. The bonded rotors have slightly weaker magnets so they need a smaller pinion :thumbsup:

[elvo]

I do have the odd relapse.





Be strong, Lee!

[Lee]

Thanks for the international support Elvo :thumbsup:


XFactory brother !!