lipo with std speedo.

[telboy]

Eyup all.
This may be an obvious answer to this question, but, If you use a standard speedo is there anything that you can use to stop the lipo going totally flat?

[eda]

These work good:

http://www.teamnovak.com/products/lipo_cutoff_module/index.html

[aeb4]

These work good:

http://www.teamnovak.com/products/lipo_cutoff_module/index.html
Can you use them when your speedo has a servo power coming from it?

[ianjoyner]

Can you use them when your speedo has a servo power coming from it?

Yes I think so, they interrupt the throttle signal to the speedo, so shouldn't matter how any power is routed.

[i4n]

I use one of them with my brushed speedo with no problems whatsoever. I know it works as I deliberately used the LiPo down to the cut off the first time I used it but in a race I've never got any where near it cutting in. In fact, in normal use I forget it is there! If you go back to using NiMh you can unplug it from the Rx and plug the speedo back inti the Rx which by-passes it completely.

When it does "stop" your car you get a bit of warning because it slows slightly as the voltage drops and then the drive goes. The steering works fine when it cuts in (so if you're mid corner you're not going to bin it!).

There are other manufacturers out there that do the same thing for a bit less so shop around Tel (I got mine when I was in the US as $2 to the £1).

[mark christopher]

tel modeltech do one too

other thing to use is your head, when the cars drops off on power, stop.
i dont think there is any rule to say you have to use a cut off device!?

[ben]

tel modeltech do one too

other thing to use is your head, when the cars drops off on power, stop.
i dont think there is any rule to say you have to use a cut off device!?

Nice to have a cut off there though ;)

[migsy]

hi lads.

if you run a FET servo, you need a voltage regulator for the servo lead as when you nail your car it will turn to where-ever it wants to.

its like a wire coil you solder to the fet wire then to the servo wire.
the outer wire side goes to the servo.

hope this helps. :thumbsup:

[Chris Doughty]

hi lads.

if you run a FET servo, you need a voltage regulator for the servo lead as when you nail your car it will turn to where-ever it wants to.

its like a wire coil you solder to the fet wire then to the servo wire.
the outer wire side goes to the servo.

hope this helps. :thumbsup:


if you are talking about a choke then its not specific to LiPo, I would recomend them being used with any 7.2v powered servo

[Supergreg]

I use this one (http://www.rcmarket.org/mc-balancer-pr-21010.html). Don't know if it's available in UK though.

[migsy]

i just find the choke helps as all my brushless systems dont have a located wire for the servo.

[Ted Maul]

These work good:

http://www.teamnovak.com/products/lipo_cutoff_module/index.html

I'll second that, very easy to install and setup and works a treat.

[SHY]

Can highly recommend the Speed Passion ESC!

In stead of cutting off it gives a "stutter" when below min. volt limit, so it's easier to get into the pits...

[jim76]

i dont think there is any rule to say you have to use a cut off device!?

not 100% sure for offroad, but there is definitely a rule in Micro Nationals that they will not let you compete without a cutoff, either built in the speedo or a seperate smart stop.
I personally think it should be a rule across all electric classes that allow lipo, even though in practice we won't use enough capacity to activate it.

I think it is more important at club level than nationals as this is where you have the lesser experienced drivers who may not be quite so organised at charging their cells etc.