PDA

View Full Version : Rc10b3 vintage racer restoration (and a b2 maybe...)


charlesk
12-11-2015, 10:41 AM
Got this box of goodies from a mate that couldn't be bothered with vintage racing anymore:

http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0037_zpsu84yawxo.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0037_zpsu84yawxo.jpg.html)

There is a decent B3 in there, that has seen quite a bit of action, it will be getting restored to almost shelfer level, but is to be used for vintage racing, so a few updates/upgrades will find their way on.

And so it begins...

charlesk
12-11-2015, 11:21 AM
First task to sort all this:http://i36.photobucket.com/albums/e34/charlesk/DSC_0038_zpsgrserrui.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0038_zpsgrserrui.jpg.html)
There is a lot of stuff, more than enough to build 2 B3s, anybody want one? Lol
5 chassis, 4 sets of towers, wishbones , 3 gear boxes, 4 sets of shocks and the he list goes on. Should be able to easily build a racer and a shelfer out of it...

There is also this:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0039_zpsmsvxlndb.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0039_zpsmsvxlndb.jpg.html)
To be probably used for some of the updates (slipper, v2 shocks etc). More on that later...

charlesk
12-11-2015, 01:35 PM
Today's task was to sort through the bits that I've got:http://i36.photobucket.com/albums/e34/charlesk/DSC_0040_zpsxqemgrx9.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0040_zpsxqemgrx9.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0042_zps9f4d4ktf.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0042_zps9f4d4ktf.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0043_zpsynhh2lqq.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0043_zpsynhh2lqq.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0044_zpsnaenus0p.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0044_zpsnaenus0p.jpg.html)
And on first view definitely got enough for 2 :D

First batch of wheels for acetone and cleaning :
http://i36.photobucket.com/albums/e34/charlesk/DSC_0041_zpsibjjrmme.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0041_zpsibjjrmme.jpg.html)

stuey
12-11-2015, 01:45 PM
Good haul. I should be getting my mitts on one soon, but I dont think I am likely to get much in the way of wheels. Not had a lot of luck finding a solution at the moment.

charlesk
12-11-2015, 04:08 PM
Good haul. I should be getting my mitts on one soon, but I dont think I am likely to get much in the way of wheels. Not had a lot of luck finding a solution at the moment.

Runner or shelfer?
I'm under the impression that rc10 worlds (rere) fit.

Welshy40
12-11-2015, 04:45 PM
Nice, if theres spares your not using let me know, running my b2 at the maritime wc at the end of the month

Peakey
12-11-2015, 05:38 PM
Nice find, what shocks do the have? I'm after a set with alloy caps if you've got any :):thumbsup:

stuey
12-11-2015, 05:50 PM
Runner or shelfer?
I'm under the impression that rc10 worlds (rere) fit.

Ok thanks for the info. I would hope to race it at some point. They do look (Worlds) a similar offset. I have some B4 fronts, but I imagine they might be a bit different offset wise.

charlesk
12-11-2015, 06:39 PM
Ok thanks for the info. I would hope to race it at some point. They do look (Worlds) a similar offset. I have some B4 fronts, but I imagine they might be a bit different offset wise.

The world's front rims fit as do the b4ones, looking at them side by side with the b3 ones, the b3 ones are slightly dished whilst the B4 ones aren't, but the difference is small and suspect a set of carrier/axles from a B4 should sort that. I'll check during the build...

stuey
12-11-2015, 07:08 PM
Ok thanks :-)

wildoliver
12-11-2015, 08:41 PM
Thats awesome!

Lucky find!

charlesk
12-11-2015, 10:20 PM
Nice find, what shocks do the have? I'm after a set with alloy caps if you've got any :):thumbsup:

One set of the Teflon coated ones have alloy caps, so those will probably end up on the shelfer.
The others (silver, v2 & Teflon) got plastic caps.
Atm until I see how many complete cars I can get out of the parts there is, there is no spare set, but we will see what comes out in the wash...

charlesk
13-11-2015, 11:43 AM
Today's progress :
http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0047_zps2dmamxln.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0047_zps2dmamxln.jpg.html)
Not coming out badly :-)

Also this lot has arrived in preparation for the build:
http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0046_zps7vnchv6i.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0046_zps7vnchv6i.jpg.html)

charlesk
13-11-2015, 12:37 PM
Thats awesome!

Lucky find!

Thanks. Been after one for a while, when he said he was thinking of letting his go, I snapped his arm off...

charlesk
15-11-2015, 02:29 PM
Not much progress this we due to being away, but got some more wheels done:http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0050_zpst8n3sxfy.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0050_zpst8n3sxfy.jpg.html)

Peakey
15-11-2015, 04:39 PM
One set of the Teflon coated ones have alloy caps, so those will probably end up on the shelfer.
The others (silver, v2 & Teflon) got plastic caps.
Atm until I see how many complete cars I can get out of the parts there is, there is no spare set, but we will see what comes out in the wash...

Well if you do have any spare let me know buddy 👍🏻

charlesk
15-11-2015, 06:11 PM
And some more wheels sorted:http://i36.photobucket.com/albums/e34/charlesk/DSC_0052_zpsmo525ugt.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0052_zpsmo525ugt.jpg.html)

charlesk
15-11-2015, 08:04 PM
The B4 has been asset stripped for shocks, bearings, ball studs etc. Looking very sad...http://i36.photobucket.com/albums/e34/charlesk/DSC_0054_zpsrbheuxe7.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0054_zpsrbheuxe7.jpg.html)

charlesk
15-11-2015, 08:06 PM
4 sets of shocks ready to rebuild, going to be a busy bee...
Also assembled a new set of cvds for the racer:http://i36.photobucket.com/albums/e34/charlesk/DSC_0055_zpsxxzdbqpp.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0055_zpsxxzdbqpp.jpg.html)

charlesk
15-11-2015, 08:09 PM
And more importantly 2 rolling chassis converted back to kit form, for cleaning, checking and reassembling :http://i36.photobucket.com/albums/e34/charlesk/DSC_0053_zpsuh2qq5fz.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0053_zpsuh2qq5fz.jpg.html)

charlesk
15-11-2015, 08:35 PM
It has now properly started, it's going to be interesting building 2 cars at the same time on a different spec.
A hopped up racer
A close to std spec B3
The big decision is which chassis to use on the shelfer. The early one with the battery cutouts, or the brand new one? Hmmm....

charlesk
16-11-2015, 02:21 PM
The tedious task of screw cleaning/derusting. Dunked in vinegar overnight, no more rust. Ready for a coat of protective oil.http://i36.photobucket.com/albums/e34/charlesk/DSC_0057_zpsspqlkiod.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0057_zpsspqlkiod.jpg.html)
Not many of these will be used, but handy as spares....

charlesk
16-11-2015, 09:18 PM
Tonight's progress. Esc rewired , new rear tower, new rear arms, hubs and cvds. Used RPM rear hangers and bumper. Oh and a few FT bits. Also some brass ballast since I'll be using shorties.

http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0059_zpscpysul7m.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0059_zpscpysul7m.jpg.html)
http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0060_zps0uitvhbu.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0060_zps0uitvhbu.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0061_zpsrgtnbfzy.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0061_zpsrgtnbfzy.jpg.html)

charlesk
17-11-2015, 09:10 AM
Decision made, the shelfer will be built as a b2 that the second rolling chassis is. Just realised last night measuring up things, the rear tower is subtly different, the front plate uses different screws, the rear plate has different flare and the chassis is slotted...

Durango
17-11-2015, 03:50 PM
Decision made, the shelfer will be built as a b2 that the second rolling chassis is. Just realised last night measuring up things, the rear tower is subtly different, the front plate uses different screws, the rear plate has different flare and the chassis is slotted...


Actually the B2 is more rare than an original RC10. The B3 is still a very fast car. I'm also racing one :)

I only see B3's on your pix... Associated released once a B2 to B3 conversion kit. So maybe one of them has been converted if there are some B2 parts on it (or spares).

Just rebuild the B2 correctly if you want a real B2. B2 has a lot of different parts, comparing to the B3: with right suspension parts on front and rear (arms, hubs...), front shock tower, rear shock tower, ball cups, slipper hubs, rear chassis plate (narrow), shocks with alloy caps., shock adjusters...Even the body was different.

B2 and B3 chassis are identical. Your chassis was modified by the previous owner. There was never a slotted chassis on the market. It's kinda "racer tip" to reduce weight and center of gravity using 6cell battery packs.

Rear NARROW aluminium chassis plate is very rare. Same story for the front top plate, WITHOUT holes for anti roll bar. Both parts are, in my opinion, a MUST HAVE on a nice B2 shelfer :)

Concerning wheels: B4 fronts will fit. Not the rears, they have a different offset. ReRe RC10 rear wheels won't fit too, as they are B4 wheels...

I'm also going to restore a B2 :) Let me know if you have a nice spare battery strap (standard length) for B3/B2 :) looking for one...

http://666kb.com/i/d3w5754v5sgaovsrg.jpg

Durango
17-11-2015, 04:00 PM
http://666kb.com/i/d3w5dkj8ac1eocnrw.jpg

http://666kb.com/i/d3w5eae8xbus1s0nw.jpg

http://666kb.com/i/d3w5erucjeivyk1ng.jpg

http://666kb.com/i/d3w5g68cjx145v2ho.jpg

Welshy40
17-11-2015, 05:36 PM
Decision made, the shelfer will be built as a b2 that the second rolling chassis is. Just realised last night measuring up things, the rear tower is subtly different, the front plate uses different screws, the rear plate has different flare and the chassis is slotted...

Also b2 front wishbones are shorter and rear wishbones as well plus have only two shock mounting holes.

If you want a good starting set up for carpet let me know. Also Thunder Tiger do a phoenix buggy which is a b3 plus do a variety of alloy options, plus wheels.

Durango
17-11-2015, 06:00 PM
Also b2 front wishbones are shorter and rear wishbones have only two shock mounting holes.

If you want a good starting set up for carpet let me know. Also Thunder Tiger do a phoenix buggy which is a b3 plus do a variety of alloy options, plus wheels.


Yup, but I think it's all metric on the phoenix? Just checked this few days ago because I wanted some option parts...

BTW: I'm using Thunder Tiger Phoenix wheels on my B3 racer.

Chillout47
17-11-2015, 07:12 PM
Don't get stuck for wheels, JC Racing still do nice 5 spokes for the B3, about £9 for a set of four.

http://www.jcracingproducts.co.uk/wheels?product_id=259

charlesk
17-11-2015, 07:45 PM
Don't get stuck for wheels, JC Racing still do nice 5 spokes for the B3, about £9 for a set of four.

http://www.jcracingproducts.co.uk/wheels?product_id=259

Look like a great choice for a runner esp :thumbsup:

charlesk
17-11-2015, 08:50 PM
Actually the B2 is more rare than an original RC10. The B3 is still a very fast car. I'm also racing one :)

I only see B3's on your pix... Associated released once a B2 to B3 conversion kit. So maybe one of them has been converted if there are some B2 parts on it (or spares).

Just rebuild the B2 correctly if you want a real B2. B2 has a lot of different parts, comparing to the B3: with right suspension parts on front and rear (arms, hubs...), front shock tower, rear shock tower, ball cups, slipper hubs, rear chassis plate (narrow), shocks with alloy caps., shock adjusters...Even the body was different.

B2 and B3 chassis are identical. Your chassis was modified by the previous owner. There was never a slotted chassis on the market. It's kinda "racer tip" to reduce weight and center of gravity using 6cell battery packs.

Rear NARROW aluminium chassis plate is very rare. Same story for the front top plate, WITHOUT holes for anti roll bar. Both parts are, in my opinion, a MUST HAVE on a nice B2 shelfer :)

Concerning wheels: B4 fronts will fit. Not the rears, they have a different offset. ReRe RC10 rear wheels won't fit too, as they are B4 wheels...

I'm also going to restore a B2 :) Let me know if you have a nice spare battery strap (standard length) for B3/B2 :) looking for one...

http://666kb.com/i/d3w5754v5sgaovsrg.jpg
Thanks for the pics if the differences, they really help.
You are right, although there is b2 parts on it, there are also some b3 parts...
The chassis looks way to neat a jot to be home cut, I suppose it could of been machined?
Also the shock tower in the background is a b3 one, the one on the front is narrower and taller?http://i36.photobucket.com/albums/e34/charlesk/DSC_0062_zpspnwq38sb.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0062_zpspnwq38sb.jpg.html)
Also, any pics of the front and rear plates?

Welshy40
17-11-2015, 09:07 PM
Yup chassis has been cut,did see a few and it did lower the weight due to the cells going through the chassis, but tbh wasnt really needed. Still agreed it does look like its been done by a pro. The b2 towers were not much different compared to B3 as holes are in the same place with exception of a few more on the b3. I prefer the b2 version.

Chillout47
17-11-2015, 10:36 PM
The tower at the back may be a worlds version, they were lower and accommodated the Deja vu shell. If you take a pic of them side by side I will be able tell. What are you doing about a shell by the way? The Deja vu tu shell looks great and a really good repro is available from TBG, I use it on my B3 runner

charlesk
18-11-2015, 07:42 AM
The tower at the back may be a worlds version, they were lower and accommodated the Deja vu shell. If you take a pic of them side by side I will be able tell. What are you doing about a shell by the way? The Deja vu tu shell looks great and a really good repro is available from TBG, I use it on my B3 runner
http://i36.photobucket.com/albums/e34/charlesk/DSC_0064_zpsylokqgt6.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0064_zpsylokqgt6.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0063_zpspghmhkly.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0063_zpspghmhkly.jpg.html)

dodgydiy
18-11-2015, 07:51 AM
i'm pretty sure the b2 and b3 rear tower are the same, wider one is the worlds tower. b2 chassis i am sure can be identified by the fact that it hasnt got 2 tiny holes at the back which the b3 has, anti roll bar mount i think??

charlesk
18-11-2015, 11:23 AM
Started to rebuild the front end.

One of the shock towers that I've got has 3 top link holes, giving the option of an even shorter front link if needed. Used this tower for the racer:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0065_zpsw1lpul92.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0065_zpsw1lpul92.jpg.html)

Also used some nice RPM front hubs from the "box of treasure":
http://i36.photobucket.com/albums/e34/charlesk/DSC_0066_zpspm3wgbog.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0066_zpspm3wgbog.jpg.html)

How the front tower currently looks. New bulkhead, new carbon composite arms and c-hubs, later FT links for a bit of bling and ease of use, and rpm link ends for strength. Aiming for as strong cas as possible:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0067_zpssijn9idw.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0067_zpssijn9idw.jpg.html)


Going through by box of bits, found these, that I believe are B2 front hubs/axles?:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0068_zpsfvqouluv.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0068_zpsfvqouluv.jpg.html)

charlesk
18-11-2015, 11:34 AM
A bit more work on the chassis. Has to remove the brass from under the batteries, because it was making them sit too high for the brace. No biggie, can use sticke. Weights in front/Behring etc to balance it out.A bit of foam spacing to locate the shorty where I expect it to end up. Nice blue brace used too. Oh and fitted the servo and pt too. Used some nice FT mounts. So here it is:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0069_zpsfh9w0msg.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0069_zpsfh9w0msg.jpg.html)
And yes the 1313 might be a bit of an overkill for a B3 but it was what I had spare and there is no harm at the end of the day.

charlesk
18-11-2015, 01:00 PM
The tower at the back may be a worlds version, they were lower and accommodated the Deja vu shell. If you take a pic of them side by side I will be able tell. What are you doing about a shell by the way? The Deja vu tu shell looks great and a really good repro is available from TBG, I use it on my B3 runner

It does look like a nice shell and in due time I might get one, but tbh atm I think I'm sorted for bodies.
2 std painted, 1 std clear and 1 painted that is a bit different (not sure what it is but quite like it):
http://i36.photobucket.com/albums/e34/charlesk/DSC_0070_zpskxjrjdtp.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0070_zpskxjrjdtp.jpg.html)

quentinfarquar
18-11-2015, 03:12 PM
Following this with interest, I have just fired my B3 up again after a 15 year break and buying some new nicads. First race at the weekend and it ran really well considering. I didn't realise the vintage scene was so strong, I was thinking if I enjoyed it I'd just by a B5m, but now I'm not sure what to do.

Any good tips or mods for the guys still running B3's, I literally just refilled the shocks (one cap did leak slightly after racing it) and put in new batteries.

Durango
18-11-2015, 03:45 PM
There is NO difference between B2 and B3 chassis plate. Concerning the worlds style shock tower on the rear: I think it was an upgrade, yes.

Another difference between B2 and B3: CVD's look different on the B2, like on the T2 truck. B3 (not the sports kit) came with MIP style CVD's

B2/B3 skinny wheels on the left - wide wheels (the same as B4 wheels) on the right (Upgrade)

http://666kb.com/i/d3x5k3qxu901ikyu4.jpg

rear B2 chassis plate on the left - rear B3 chassis plate on the right

http://666kb.com/i/d3x5mncgfnwvhqgkc.jpg

B2 on the left - B3 on the right. Note the difference on shock tower, shocks, top plate, arms.. (last B2 models had the same top plate as the B3, with holes for a anti-roll bar on the front)

http://666kb.com/i/d3x5mzzbzjs4r9ysc.jpg

Rear B2/B3 shock tower on the left - worlds (B3) option part on the right

http://666kb.com/i/d3x5oyge83jw2yc0s.jpg

http://666kb.com/i/d3x5q65w1aq66bskc.jpg


http://666kb.com/i/d3x5qg59nxdz9z3vg.jpg

Durango
18-11-2015, 03:57 PM
Going through by box of bits, found these, that I believe are B2 front hubs/axles?:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0068_zpsfvqouluv.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0068_zpsfvqouluv.jpg.html)

These are B4/T4 hubs.

J'MM'N
18-11-2015, 04:05 PM
Only difference between a B2 and B3 chassis, is the B3 has two extra holes to accommodate a rear anti roll bar.

Durango
18-11-2015, 04:12 PM
Only difference between a B2 and B3 chassis, is the B3 has two extra holes to accommodate a rear anti roll bar.

Show me please, I'm comparing my B3 with my B2 chassis and don't see these extra holes :eh?:


PS: Oh damn yeah, you're right. I don't know why, I never noticed these

Welshy40
18-11-2015, 04:43 PM
Following this with interest, I have just fired my B3 up again after a 15 year break and buying some new nicads. First race at the weekend and it ran really well considering. I didn't realise the vintage scene was so strong, I was thinking if I enjoyed it I'd just by a B5m, but now I'm not sure what to do.

Any good tips or mods for the guys still running B3's, I literally just refilled the shocks (one cap did leak slightly after racing it) and put in new batteries.

B4 layshaft, vts slipper and a few rude tony weights and should be really good, full size servo, preferably metal geared as this adds weight to the front. I dont enjoy driving the B5 but get a thrill when using my B2 hence why im using mine on 28th at Maritime world cup event. Ok my car was modded well before the 3 came out we found the car was much more stable when we widened the front end, but didnt like a wider rear so preferred the same rear end on the B2 as it made the car easier to drive. I also used zero degree rear hubs and mounts (used 1.5 as well)as it made the car more agressive in and out of corners. I also found the standard gold shocks from the stock car were smoother and got a more dialed car. Corally ten double and it was a really fun car to drive, now lipos cause problems as you need to find the weight that the cells used to be but still entertaining never the less.

J'MM'N
18-11-2015, 04:52 PM
Sorry for poor image, but have circled hole for ARB on a B3 and is not applicable on B2's.

P.S. Just noticed your edit :)

Welshy40
18-11-2015, 05:29 PM
Forgot to mention, i found the best way in the 90's at the highest level of keeping the front wishbones in one piece was to do the method on both b2 and b3 and use two metal wishbone plates, you will need to cut away an area of the wishbones to do this but does add a bit more strength. :thumbsup:

quentinfarquar
18-11-2015, 05:39 PM
B4 layshaft, vts slipper and a few rude tony weights and should be really good.

Sounds good could you expand a bit on this, what do I do with Rude Tony weights.

charlesk
19-11-2015, 10:25 AM
Shock rebuild time. Everything stripped to clean/check. Doing this for.all 4 sets at the same time:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0073_zps0stesgpr.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0073_zps0stesgpr.jpg.html)
The set to the top left got red 3 hole rear pistons, with no other markings on, anybody has any idea what they are?

charlesk
19-11-2015, 10:28 AM
And the tools of the trade 😁 :http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0075_zps8whaxwsi.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0075_zps8whaxwsi.jpg.html)

charlesk
19-11-2015, 10:53 AM
Oh and these arrived today so can crack on now :-D http://i36.photobucket.com/albums/e34/charlesk/DSC_0076_zpshp5lyg3z.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0076_zpshp5lyg3z.jpg.html)

charlesk
19-11-2015, 01:41 PM
The envy of usable b3 gearboxes??? B4 layshaft, new outdrives, ceramic balls and thrust, oh and new plates:http://i36.photobucket.com/albums/e34/charlesk/DSC_0077_zps1fllducb.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0077_zps1fllducb.jpg.html)

Welshy40
19-11-2015, 06:30 PM
Sounds good could you expand a bit on this, what do I do with Rude Tony weights.

B4 layshaft is a perfect fit, the same size gear as the B2/3 so having this layshaft means you can have a decent slipper. With VTS installed it makes the car much easier to drive, it sounds like not much but whilst developing my Lazer ZXR i was three laps off the pace with a standard slipper, with a b4 slipper i was 1 and a third of a lap off the pace and with the VTS was only half a lap off the pace and looking at the times i was putting in had instances where it showed i was right on the pace. The VTS is a superior slipper compared to the standard set up and twin pad set up. Youll need to buy the rpm gear cover to use this slipper though.

Brass thin plates that are a perfect fit for the battery section, basically i use several to get the car up to the weight of scrc or nimh batts as the batteries used then were much heavier.

quentinfarquar
19-11-2015, 09:24 PM
So its a straight forward mod, the thing is I raced it last week for the first time in 15 years with all the old gear just 2 new nicads, so the thing is do i play about with the B3 or just by a B5M and modern electrics...

charlesk
19-11-2015, 10:02 PM
So its a straight forward mod, the thing is I raced it last week for the first time in 15 years with all the old gear just 2 new nicads, so the thing is do i play about with the B3 or just by a B5M and modern electrics...

Imo, a B3 is great for vintage racing, but against modern cars on high grip surfaces it will be slower. Easier to drive but slower. So it depends on what you want out of your racing.
Another thing to consider is parts, as they aren't as readily available as for something like a B5M.
It comes down to the amount of use and your ability to keep it running as breakages and Wear will take its toll...
I race vintage in vintage class once a month ish with a vintage car, but a modern buggy week in week out.
Oh and modern electrics all the way unless it's a shelfer or used once/twice a year..

Welshy40
20-11-2015, 10:48 AM
As per above, personally would choose wisely, B5 isnt easy to drive and didnt like it so would advise asking to try someones before buying. Im running mine as my sponser cant get me the new sworkz in time for the next event and mods arent expensive but does mean i wont come last.

quentinfarquar
20-11-2015, 03:10 PM
maybe I should use if for a few weeks and see if Im going to stick at it. I'd like to but I guess its the family. Then take the plunge...

So if not a B5m what should be on my list, my first time racing as a kid I only raced Cougars, then when I came back in 2000 I bought this B5 from a guy for about £70 and it seemed a great car, no issues at all.

I have an 13 triple in it, running on nicads and its plenty fast enough in a straight line, but I guess the newer cars handle better.

Welshy40
20-11-2015, 06:06 PM
maybe I should use if for a few weeks and see if Im going to stick at it. I'd like to but I guess its the family. Then take the plunge...

So if not a B5m what should be on my list, my first time racing as a kid I only raced Cougars, then when I came back in 2000 I bought this B5 from a guy for about £70 and it seemed a great car, no issues at all.

I have an 13 triple in it, running on nicads and its plenty fast enough in a straight line, but I guess the newer cars handle better.

Thing is technology has changed and brushless is the product now, bit more torque. There are loads available, Schumacher does a good car but with these guys they change the design every five minutes so i tend to avoid them due to that but will say they designed a stunning car for 2wd. Losi do a good car also but tight for electrics, sworkz have shipped their first batch so may hit our stores shortly and is a very good car design plus made tough like their 4wd. Id avoid Durango, cars crap, as youll never have just one setup and means youll never have a perfect setup and will drive you crazy. There are quite a few to choose but is really down to your taste, after all if it looks right then great start.

charlesk
21-11-2015, 08:27 AM
Back on track now, a decent amount of progress the last couple of days. It's on the final straight :-)
Front clip now on, made up a decent steering link (remember from my b44 that the stock link had a tendency to let go)
http://i36.photobucket.com/albums/e34/charlesk/DSC_0074_zpsx2froibk.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0074_zpsx2froibk.jpg.html)
Got this little monster to power it up. Should be plenty with a bit of boost.http://i36.photobucket.com/albums/e34/charlesk/DSC_0075_zpsv4scbddj.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0075_zpsv4scbddj.jpg.html)
And how it's looking atm.http://i36.photobucket.com/albums/e34/charlesk/DSC_0073_zps3kk3uje4.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0073_zps3kk3uje4.jpg.html)
Rpm front bumper too :-)

charlesk
21-11-2015, 10:23 AM
Didn't have a shock stand for small bore shocks so made one up. Effective and tasty 😁 http://i36.photobucket.com/albums/e34/charlesk/DSC_0076_zpspk2ljzhh.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0076_zpspk2ljzhh.jpg.html)

bretts
21-11-2015, 10:25 AM
Nice!! You should send this to Racer Magazine for 'Tip of the Month' :-)

charlesk
21-11-2015, 10:47 AM
Shocks ready to go on:http://i36.photobucket.com/albums/e34/charlesk/DSC_0077_zpsxptz23gw.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0077_zpsxptz23gw.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0079_zpskbxkby17.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0079_zpskbxkby17.jpg.html)

Welshy40
21-11-2015, 11:12 AM
Great shock stand idea and nicely laid out.

charlesk
21-11-2015, 02:08 PM
Nice!! You should send this to Racer Magazine for 'Tip of the Month' :-)
Start with full jar of Nutella, eat to empty, rim hole to the lid :lol:

xfactor
21-11-2015, 02:42 PM
Nice, coming along great now.

Just check your front turnbuckles. Think the studs should be behind the front tower not in front.:thumbsup:

charlesk
21-11-2015, 02:47 PM
Nice, coming along great now.

Just check your front turnbuckles. Think the studs should be behind the front tower not in front.:thumbsup:

Cheers. You're 100% right, I've noticed it after I took the pic:blush: I'll sort tonight when I'm back home.

Welshy40
21-11-2015, 03:01 PM
Your cars coming along nicely. Here is some pics of mine. Rear tower is my design and has wire holes cut out for neat placement and is made by Fibrelyte (link below in my name tag. Youll notice my twin metal wishbone brace on the front for more strength. and VTS slipper ican just be made out in the picture, plus rude blitz brass cell weights and cut out areas for the wiring. Ive got the wrong length steering turnbuckle fitted so will get around to replacing and will change the ball joints as the B4 version isnt as good as the TC version that came with the B2

Just waiting for the front full spikes to arrive so I can fit them and hope she is up to the pace im gonna put her at next week.

charlesk
22-11-2015, 05:05 AM
How it's currently Looking:

http://i36.photobucket.com/albums/e34/charlesk/DSC_0080_zpsxcmgw4jf.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0080_zpsxcmgw4jf.jpg.html)

A bit of soldering left to do, sort wheels and tyres and which body to use.

Welshy40
22-11-2015, 12:43 PM
Car looks stunning. Post your set up as im intreagued with that battery.

Mine is 30 weight front size one piston, black springs, 25 degree castor
35 rear size one piston, silver springs, zero or one degree hub, zero or 1 degree wishbone holder. Battery im using is hpi 5600 saddles and all forwards with foams behind, no rollbar.

Ceramic big diff balls, tungsten thrust.

charlesk
22-11-2015, 06:06 PM
Car looks stunning. Post your set up as im intreagued with that battery.

Mine is 30 weight front size one piston, black springs, 25 degree castor
35 rear size one piston, silver springs, zero or one degree hub, zero or 1 degree wishbone holder. Battery im using is hpi 5600 saddles and all forwards with foams behind, no rollbar.

Ceramic big diff balls, tungsten thrust.

Thank you :blush:, must admit I'm quite happy with it.
Setup, my starting setup.is quite different to yours (its heavily based on a French carpet setup from petitRc), but can't say how it drives yet, so will update once it's run and I've made changes to get close to what I like.
I've got a decent amount of weight under the spacing foams to weigh the car down, can't see a 200g battery working in this without extra weight...

charlesk
22-11-2015, 06:09 PM
Gear cover in place Rpm from the B4:http://i36.photobucket.com/albums/e34/charlesk/DSC_0083_zpszgjfnjmh.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0083_zpszgjfnjmh.jpg.html)


Wiring done. Esc calibrated and set to something close to what I expect to want, we shall see...http://i36.photobucket.com/albums/e34/charlesk/DSC_0082_zpsrtpo1ajx.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0082_zpsrtpo1ajx.jpg.html)

Wing on. Body and wheels still to sort, hopefully tomorrow.http://i36.photobucket.com/albums/e34/charlesk/DSC_0081_zpsm8nyiuhg.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0081_zpsm8nyiuhg.jpg.html)

charlesk
23-11-2015, 10:18 AM
Thought to share another little secret/update of this car:http://i36.photobucket.com/albums/e34/charlesk/DSC_0086_zpsexpyzitc.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0086_zpsexpyzitc.jpg.html)
Avid triad. Contemplated using a vts, but since I run these in my modern cars, this simplifies spares etc.

Peakey
23-11-2015, 10:48 AM
Coming along nicley, have you already got a shell for it?

charlesk
23-11-2015, 11:05 AM
Coming along nicley, have you already got a shell for it?
Thank you. Got 3 painted shells that came with it, 1 that I quite like, so I'll start with that, and then possibly it the future paint one on my current colours. Suggestions however are more than welcomed :)

Welshy40
23-11-2015, 12:26 PM
Great, good idea on the slipper, it should go really well.

charlesk
23-11-2015, 12:49 PM
This shell is on for now, I quite like it but it's not in my colours. It will do for now:http://i36.photobucket.com/albums/e34/charlesk/DSC_0087_zps1xkwq4r2.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0087_zps1xkwq4r2.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0088_zps3wcj4v1v.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0088_zps3wcj4v1v.jpg.html)

charlesk
25-11-2015, 08:34 PM
Second car started being built, the intention for this is to be a nice close to std spec b3, probably as an occasional runner.
Using the modified chassis with thebattery cutouts and new stainless screws. Early stages but:
http://i36.photobucket.com/albums/e34/charlesk/Mobile%20Uploads/DSC_0090_zpsbahkjj97.jpg (http://s36.photobucket.com/user/charlesk/media/Mobile%20Uploads/DSC_0090_zpsbahkjj97.jpg.html)

charlesk
26-11-2015, 07:45 PM
Coming along nicely:
http://i36.photobucket.com/albums/e34/charlesk/DSC_0091_zpszhabgege.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0091_zpszhabgege.jpg.html)

Welshy40
26-11-2015, 08:09 PM
Whre did you get the screws from?

charlesk
26-11-2015, 08:58 PM
Whre did you get the screws from?
My pitbox I'm afraid, it's a selection of screws from various older associated cars inc (and not limited) a b4, b44.3, rc10wc etc...
Haven't found a b2/3 specific kit yet, but it's not too difficult to make up one, I'm keeping track of what is being used and then might be able to put together a set :thumbsup:

charlesk
28-11-2015, 05:44 PM
Front ends and shocks assembled :
http://i36.photobucket.com/albums/e34/charlesk/DSC_0092_zpszombwb0r.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0092_zpszombwb0r.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0093_zpsbkomqkqf.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0093_zpsbkomqkqf.jpg.html)
New orings in the shocks, they feel quite nice :-)

charlesk
29-11-2015, 04:54 PM
Gearbox on:http://i36.photobucket.com/albums/e34/charlesk/DSC_0094_zpsjt02tyl4.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0094_zpsjt02tyl4.jpg.html)http://i36.photobucket.com/albums/e34/charlesk/DSC_0096_zpsiof2illn.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0096_zpsiof2illn.jpg.html)
Kept things original in this car. Diff rebuilt and feels nice and smooth now. It only had 2 bearing and 4 thrust balls to start with :o

charlesk
29-11-2015, 06:36 PM
This one is now complete too :-) http://i36.photobucket.com/albums/e34/charlesk/DSC_0097_zpsijieqtf8.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0097_zpsijieqtf8.jpg.html)
Shinydrive
http://i36.photobucket.com/albums/e34/charlesk/DSC_0098_zpsoorrxyhi.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0098_zpsoorrxyhi.jpg.html)
Only thing missing is std battery brace but one on the way :-D

charlesk
29-11-2015, 06:52 PM
Body and a wing on:http://i36.photobucket.com/albums/e34/charlesk/DSC_0100_zpsagq1byp1.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0100_zpsagq1byp1.jpg.html)
Anybody fancies a B3 lol?

Welshy40
01-12-2015, 10:13 PM
Very very nice



Ok after doing an event this weekend, found the perfect carpet set up. Size one all round pistons, 30wt front oil with black springs, 35wt rear oil with silver springs. 25 degree castor blocks. Tie rod ball joint Inner hole on front shock tower and rear tower. middle hole on front tower if using three hole for top of shock, and middle / inner on rear (basically i prefer front & rear shocks angled identically. Rear wishbones, middle hole (if using 3 hole wishbones, otherwise outer if 2 holes). Front wishbone outer hole. Battery saddle pack forward placement with foam insers by rear tower. 10g weight on either side of full size servo (used for more weight). Vts slipper clutch fitted with ceramic diff balls and tungsten thrust race. Rear hubs set on middle. 2wd slim yellow mini pins and uncut, rear yellow mini pins uncut. Ride height rear with 1mm spring spacer and no spring clamp. Front with spring clamp and 4mm spacer. Shocks worked better with 1mm pack so gets hard to push shaft fully into body 1mm from end of travel, with standard silver shock shafts as gold is a lot harder to get pack.

Hope this helps

Durango
02-12-2015, 08:10 AM
Very very nice



Ok after doing an event this weekend, found the perfect carpet set up. Size one all round pistons, 30wt front oil with black springs, 35wt rear oil with silver springs. 25 degree castor blocks. Tie rod ball joint Inner hole on front shock tower and rear tower. middle hole on front tower if using three hole for top of shock, and middle / inner on rear (basically i prefer front & rear shocks angled identically. Rear wishbones, middle hole (if using 3 hole wishbones, otherwise outer if 2 holes). Front wishbone outer hole. Battery saddle pack forward placement with foam insers by rear tower. 10g weight on either side of full size servo (used for more weight). Vts slipper clutch fitted with ceramic diff balls and tungsten thrust race. Rear hubs set on middle. 2wd slim yellow mini pins and uncut, rear yellow mini pins uncut. Ride height rear with 1mm spring spacer and no spring clamp. Front with spring clamp and 4mm spacer. Shocks worked better with 1mm pack so gets hard to push shaft fully into body 1mm from end of travel, with standard silver shock shafts as gold is a lot harder to get pack.

Hope this helps

Thanks Welshy for sharing, this will be helpful :)

charlesk
02-12-2015, 07:38 PM
Very very nice



Ok after doing an event this weekend, found the perfect carpet set up. Size one all round pistons, 30wt front oil with black springs, 35wt rear oil with silver springs. 25 degree castor blocks. Tie rod ball joint Inner hole on front shock tower and rear tower. middle hole on front tower if using three hole for top of shock, and middle / inner on rear (basically i prefer front & rear shocks angled identically. Rear wishbones, middle hole (if using 3 hole wishbones, otherwise outer if 2 holes). Front wishbone outer hole. Battery saddle pack forward placement with foam insers by rear tower. 10g weight on either side of full size servo (used for more weight). Vts slipper clutch fitted with ceramic diff balls and tungsten thrust race. Rear hubs set on middle. 2wd slim yellow mini pins and uncut, rear yellow mini pins uncut. Ride height rear with 1mm spring spacer and no spring clamp. Front with spring clamp and 4mm spacer. Shocks worked better with 1mm pack so gets hard to push shaft fully into body 1mm from end of travel, with standard silver shock shafts as gold is a lot harder to get pack.

Hope this helps

Thanks for that, should be useful for the weekend ��
Actually managed to give mine its first run today. It was outdoors on high grip astro. Made a couple of small changes to my staring setup resulting in a car that was v consistent and easy to drive and at the same time quick (only thing holding it back in places was me not wanting to break it).
My setup at the end of the day:

Front:
Yellow low pro cut staggers
20mm ride height
No1 pistons, 32.5wt oil, brown springs
Shocks middle on the tower and outer on arm
Link middle height outer, middle hole on tower
25 deg hubs
Std Ackerman
0.5deg camber

Rear:
Yellow rear minipin
20mm ride height
No1 pistons, 27.5wt oil, silver springs
Shocks middle on tower, outer on arm
Link inner on tower, inner on hub
0deg hubs
Diff medium/loose

10g either side of the servo
60g straight behind the servo (in battery compartment)
Shorty battery against the weights
40g behind shorty

A couple more things to try, red/green from springs and maybe drop front oil to 27.5-30wt, 2deg rear blocks (to make the car a touch more aggressive on turn in)

charlesk
04-12-2015, 01:31 PM
Couple of bits that arrived today, that will finish off the pink car, and give me a spare, when I come across tricky parts I always buy a spare...
http://i36.photobucket.com/albums/e34/charlesk/DSC_0104_zpsmpxbk8ma.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0104_zpsmpxbk8ma.jpg.html)

stuey
28-01-2016, 08:02 PM
Hi guys, a quick B3 question if I may. I got a B3 sport from my Dad at xmas, and I'm prepping it ready for racing again. I managed to get a set of CVD's (thanks DMS) which have the 3/16 axle. I did get some wheels with the car, but not many. I think the worlds re-re rears fit ok, I have a header card with 6805Y which seems to be the same part number. The fronts are more of a problem. I have fitted some B4 fronts which have BB greens on (hopefully to run at the weekend), but the offset is too narrow. I thought the worlds re-re fronts might work, but spares lists look like they show B4 wheels. Is there anything currently available that would give the right offset, other than the JC wheels? Cheers :D

Welshy40
02-02-2016, 03:17 PM
Phoenix buggy from thunder tiger is a b3 in drag. Wheels fit and have a pair myself. You can get alloy upgrades as well like rear tower mount and front alloy block. Think the screws are not usa style though.

stuey
03-02-2016, 08:24 AM
I saw there is a conversion for the RC10 Worlds to run B4 wheels. I had a look, it looks like it comes with a longer stub axle which makes up for the different offset. I am pretty sure it will fit, and the axle is available seperately. I'm not sure if it will be ok to run it like that at the Iconic revival or not though. Thanks Welshy:)

stuey
03-02-2016, 08:29 AM
BTW, is it the Phoenix BX II that is the clone? Looks like it!

stew_zs
03-02-2016, 08:42 AM
Rc10 3/16 wheels should fit the tears on a b3. And if you get some wide axles for the front b4 wheels give the same offset as the old b3 ones.

That's what I will be running on my cars this year.

stuey
03-02-2016, 09:05 AM
I have the CVD's in my car now, so yeah the Worlds 3/16 wheels look right. I have one pair of wheels I had to open up the hole slightly to fit for some reason. I am going to check with Iconic re the fronts, if they are hard to find hopefully it wont be an issue running the B4 fronts.

stew_zs
03-02-2016, 09:47 AM
Shouldn't be a problem at all mate !! There's quite a few who do mods to make wheels fit !!

charlesk
07-03-2016, 08:09 AM
A bit of an overdue update.
The B3 has been really good both outdoors and indoors, with only the typical issue of rear motor cars on high grip of not enough steering on power/front end lifting under hard acceleration, not made better by me using shorties which are considerably lighter than the nicd/nimh that it was originally designed to use.
So a bit of extra weight at the front especially was going to help.
Had a couple of us tomorrow weights drawn and made which really help a lot and look far better (imo) than the typical solution of stick ons...http://i36.photobucket.com/albums/e34/charlesk/DSC_0154_zpsqhy5zqwk.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0154_zpsqhy5zqwk.jpg.html)
The one in the battery compartment is stackable allowing to fine tune how much weight to use no wraps around the post to maximise space and weight available.http://i36.photobucket.com/albums/e34/charlesk/DSC_0156_zpsyod0fcmo.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0156_zpsyod0fcmo.jpg.html)
Also make some rc10 specific nose weights for the same reasonhttp://i36.photobucket.com/albums/e34/charlesk/DSC_0155_zpsskollejq.jpg (http://s36.photobucket.com/user/charlesk/media/DSC_0155_zpsskollejq.jpg.html)

stuey
07-03-2016, 08:40 AM
Nice job. I made a piece of lead flashing that sits under my saddle pack cells in my B3, the same size as the battery tray area. It puts the weight approx back to what round cells would be. I need to try it without and see how it drives, and try moving some weight around. I have noticed it jumps pretty nose high which is a pain, so it might need some weight further forward. I also think it has a washer under the rear toe block reducing the anti squat.

charlesk
20-08-2019, 07:18 PM
Been a while, but still love B3s, so decuded to build another one, mostly from nip parts that I have hoarded over the last few years.
Current stake of play plus the cards of some of the nip bits used. :woot:

charlesk
24-08-2019, 10:47 AM
Ko fet servo in, turnbuckles built, receiver in.

fidspeed
24-08-2019, 01:59 PM
nice Charles need to run iconic next year give mitch a run for his money

cheers Dave

charlesk
24-08-2019, 04:22 PM
nice Charles need to run iconic next year give mitch a run for his money

cheers Dave

Don't think I'll be able to bring myself to use this one in anger tbh Dave.
The other one on the other hand...

fidspeed
24-08-2019, 06:27 PM
do it Charles
it's at Bingham again well be there all being well :D:D

charlesk
01-09-2019, 07:35 PM
Getting there...

charlesk
01-09-2019, 07:39 PM
And finally got my hands on the illusive B2😁
Came without the shell (had that for years), but it's really tidy. Will have a quick clean etc and be the next vintage project...

ste_lazzaro
05-09-2019, 06:17 AM
Getting there...
:thumbsup:
Lovely!:woot:

charlesk
06-09-2019, 05:31 PM
The b2 has working electrics now. Ignore the receiver, waiting for an appropriate one😉

charlesk
13-09-2019, 09:38 AM
B3 wing painted and stickered up.
Still debating what to do with the body...

isobarik
13-09-2019, 10:37 AM
The b2 has working electrics now. Ignore the receiver, waiting for an appropriate one😉

Is it me or is that servo like huge/long ??????

Mvh ISO

charlesk
13-09-2019, 01:44 PM
Is it me or is that servo like huge/long ??????

Mvh ISO

Tight fit, but actually a std size servo...

Welshy40
13-09-2019, 04:05 PM
Iso, want to borrow my glasses 👓 🤣, looks spot on to me.

isobarik
13-09-2019, 10:02 PM
Tight fit, but actually a std size servo...

Looks Huge from the ears down, what is it ???

Mvh iso

isobarik
13-09-2019, 10:04 PM
Iso, want to borrow my glasses 👓 🤣, looks spot on to me.

What are you doing im suppose to be the Chekey one 😀😆

Mvh iso