PDA

View Full Version : KF2 Configuration


Danosborne6661
10-07-2016, 08:53 PM
With the latest generation of cars like the YZ-2, XB2 and B6 running a lot more mid weight and a lighter rear end than previously. I wondered if anyone had tried a slightly different configuration in their KF2?

Rather than running the low grip set-up, I'm considering moving the motor 20mm further forward, then putting a shorty lipo in the forward position in the space where you'd put saddles? This way you'll get a bit more weight around the mid and take some away from the rear.

Thoughts?

mark christopher
11-07-2016, 08:10 AM
ben jemmo runs kf2 kit motor position, and stubby where saddle is, details on petite rc

Danosborne6661
11-07-2016, 08:36 AM
You got a link? Can't seem to find it!

mark christopher
11-07-2016, 04:36 PM
http://site.petitrc.com/setup/schumacher/setupcougarkf/KF2_BenJemison_RHR20150322/

bish
11-07-2016, 05:56 PM
Interesting- i wonder what length belt? I can't see any further detail from the pictures.

Edit;
DOH! 117T clear as day...

paulc
11-07-2016, 09:40 PM
I run the motor in kit position with a shorty lipo but use the Schumacher K2 battery straps so you can have the battery back or forward here's Bens from Petit site

http://site.petitrc.com/setup/schumacher/setupcougarkf/KF2_BenJemison_RHR20150322/

Danosborne6661
12-07-2016, 08:54 AM
I run the motor in kit position with a shorty lipo but use the Schumacher K2 battery straps so you can have the battery back or forward here's Bens from Petit site

http://site.petitrc.com/setup/schumacher/setupcougarkf/KF2_BenJemison_RHR20150322/

I plan on doing the same Paul rather than the shorty being fixed in place, I'm most inclined to try the shorty in the forward position!

My dad has also been experimenting around with removing plates from the slipper assembly in certain conditions, this could work quite well with this 117t belt set-up if you want more of a 4-gear action in slippy conditions instead of the '3.5-gear' feel.

For those after the 117t, part number is U4494 :)

ianjoyner
12-07-2016, 11:05 AM
Even with the low grip layout the weight is a long way forwards, not to say there isn't an advantage to putting the motor all the way forwards if the grip on the track is there. I was thinking of trying motor forwards, but shorty at the back on astro.

Danosborne6661
12-07-2016, 12:59 PM
I've already been running 40g infront of the motor for the last little while, so makes sense for me to try the motor forward by 20mm.

The latest generation of cars are incredibly light weight on the rear end, but they seem to get round this by mounting the shock much further in on the rear tower so I may try adding a new hole!

ianjoyner
12-07-2016, 01:21 PM
Putting the rear shocks forwards and running an LCG LiPo are also options for moving the weight forwards.

Danosborne6661
13-07-2016, 08:09 PM
Ready to test at Mendip RC Raceway tomorrow evening!

Motor moved 20mm further forward as per kit (non low grip conversion), shorty in the forward position, rear shock tower redrilled to move the shocks further in as an option. Just waiting for the 117t belt to arrive tomorrow :)

http://i.imgur.com/fMecpHc.jpg

mark christopher
13-07-2016, 08:56 PM
http://www.racing-cars.com/pp/New_Cars_and_Parts/Cougar_KF2/U4403.html


http://www.racing-cars.com/images/u4403_w.jpg

mrspeedy
13-07-2016, 10:08 PM
http://www.racing-cars.com/pp/New_Cars_and_Parts/Cougar_KF2/U4403.html


http://www.racing-cars.com/images/u4403_w.jpg

They're coming with the belt tomorrow :thumbsup:

ianjoyner
14-07-2016, 11:59 AM
Looks good Dan, are you going to try LiPo forwards and backwards?

Danosborne6661
15-07-2016, 10:50 AM
Looks good Dan, are you going to try LiPo forwards and backwards?

I just plan on running it in the forward position and adapting the set-up to suit. Last night we tried it at Mendip RC Raceway's bumpy, high-grip astro track and it went great! A few changes were needed to get it there though :)

Extra hole inwards on the rear tower
We drilled in extra hole inwards on the rear tower, a lot of the 3-gear cars have the shocks a lot more led down so we thought we would try the same. Works good with this new layout and the bumps on the track just vanished!

All slipper pad weights removed except a standard dual set-up
The slipper assembly works great on the low grip layout, but not so much with this new layout! With the extra forward weight AND the large slipper assembly the car was pitching forward too much. We removed all the pads except 2x like on a standard slipper set-up and used a 5mm bearing as a spacer where the spring sits to help pinch up the new set-up. Removing all the pads stops the car pitching around as much and keeps it much more neutral, was skimming over the bumps with ease now!

Shorty weight under lipo
I tried a few different weights under the lipo as well. 35g under the lipo tamed the car down which was nice to drive but a little lively. 70g took too much steering away and caused the rear to lean a little too much. I'll probably end up switching between 35/50g under the lipo depending on what I want the car to do.

+50cst/2.5wt in front shocks
With the weight being that much further forward, the car was diving quite a lot off power and actually causing the rear inside wheel to nearly lift and the geared diff to diff out! I'd suggest if you try this forward layout, you need to add +50cst weight in your front shocks to compensate :)

Overall though the car was real good, and probably the best my KF2 has felt! I'll be running this same set-up in the wet too, will just need a few tweaks.

chrispattinson
18-07-2016, 09:55 AM
Thanks for the feedback Dan, top stuff.

For the past two years, I've settled on running the KF with kit motor position (and running the shocks on the front of the rear wishbone), but running saddles, with longest wheelbase. The car has a much better balance, and rides the bumps a lot better. We run some fairly bumpy regionals here in the NE, and I've very happy with the way the car glides around the track now.

My thoughts were that the rear of the car was over rotating on power in other configurations, so reducing the weight in the rear of the car, reduced the momentum of the rear of the car rotating.

I played around with moving shocks from the front to the rear, but though I couldn't find a happy medium, I preferred them on the front of the wishbone, and this reduced the over rotation, and gave more steering. Last night I went to small bore rear shocks, mounted on the front of the wishbone, and this was the best it had felt.

Im on 550 front oil black springs, 350 rear oil red springs (small bore).

I also found running the front wishbones on long wheelbase, meant the front wasn't pitching in too much with the weight further forward.

The setup seems to work well on astro, grass, carpet, and multi surface.

I'm going to fit the 117T belt , and try a shorty fwd like yourself, maybe this will be going too far with moving weight fwd, considering my shock position?

I hadn't thought of leaning the rear shocks in further, I might give that a go aswell.

Thanks again for the feedback, Chris.

ianjoyner
20-07-2016, 07:06 AM
Thanks for posting Dan.

What rear springs and lower shock position were you running?

What were you thinking for the wet?

Cheers

mrspeedy
20-07-2016, 01:05 PM
I'll reply as I've been running this setup with Dan ..

We have been using mostly kit setup all round, so red rear springs on middle wishbone hole, with 3 x 1.7 pistons on 400cst oil ... and seems to work quite well on bumpy high grip astro.

Moving the shocks in on a new hole in the tower loosens the back up in the turns more than kit, doesn't feel so locked in .. takes a while to get used to but seems to work with the lower rear weight bias.

Taking the slipper plates out seems a really good tuning option with this layout too .. stock slipper has quite a forward kick on power ..

chrispattinson
21-07-2016, 08:08 AM
Do you think running motor forward causes a problem of the rear being too locked in though? Just wondering why you are looking to free the back end up with laid down shocks when moving weight forward, I would have thought, and have experienced the opposite to be true .... where moving the weight forward has increased steering, and so no need to free up the rear. But....... consider, my shocks are on the front of the rear wishbone.

mrspeedy
21-07-2016, 02:46 PM
It's hard to say really. Its a setup we thought up to try and get the KF to work more like the YZ2 and B6/B5m laydown ... they just seem to drive round our track (Mendip) like they're on rails ... and better over the bumps by miles !!

A more central weight gives more natural stability, moving the shocks in on the tower makes the suspension softer and more progressive and adds back in the traction plus steering .. it definitely has a good feel about it ..

All I can say is try it ... its an easy conversion ..

chrispattinson
21-07-2016, 03:29 PM
Thanks, will try it this weekend.

mrspeedy
21-07-2016, 04:11 PM
Cool .. let us know how you get on :thumbsup:

chrispattinson
25-07-2016, 02:11 PM
So, with the revised layout, I attended NEAM at Seaham on Sunday night. Its a all carpet with typical indoor features. On the flat, the car was very good, very sharp, without over rotating. A bit more lively than with the saddles in.
But we had some overlapped gym mats, and small moguls, which the back of the car was skipping about on too much.
I moved the shorty position further back, to stop the back skipping up too much, and this worked well.
I ran like this for the final few runs of the night, very happy with the cars pace ..... rapido.

I can't help but feel, that it'll be quicker with the shorty further forward though, if I can manage to somehow keep the rear in check over the bumps.

mrspeedy
25-07-2016, 03:25 PM
Sounds like you liked the layout :thumbsup:

Did you try with a new hole drilled in the shock mount ? .. and did you run stock slipper or the stripped down version ?

chrispattinson
25-07-2016, 07:16 PM
Hi,
I used a lightweight slipper assembly. I had the shocks drilled around 12mm inboard of the existing inboard hole. See the picture attached.

mark christopher
26-07-2016, 08:20 AM
Could also use the alloy side rails and loose the top deck.

bish
26-07-2016, 01:22 PM
*slight tangent*
Alloy stiffeners or carbon top deck? Which one and why? I'm just about to get the MM carbon chassis and could do with a bit of a point in the right direction! I'll be swapping between carpet/astro and dirt configurations.

chrispattinson
27-07-2016, 07:08 AM
Could also use the alloy side rails and loose the top deck.

Hi Mark, good idea, but this car is a KF1, so there isn't an option of alloy side rails.
Chris.

mark christopher
27-07-2016, 11:12 AM
Hi Mark, good idea, but this car is a KF1, so there isn't an option of alloy side rails.
Chris.

There is u4892 fits as I have them on my kf1 so it looks like the one Ben is running.....

mark christopher
27-07-2016, 09:33 PM
Hi Mark, good idea, but this car is a KF1, so there isn't an option of alloy side rails.
Chris.

KF1 with alloy stiffeners


https://scontent-lhr3-1.xx.fbcdn.net/t31.0-8/13701077_10153731186156156_3036734788268945818_o.j pg

chrispattinson
29-07-2016, 07:30 AM
Thanks Mark, I'll give it a try.

Danosborne6661
29-07-2016, 10:26 AM
Cars been going really well in this configuration, definitely won't be going back to the other layout! Been experimenting with 30-50g weight under the lipo in different conditions.

12mm seems a long way to drill the rear shock position! We've drilled ours about 6mm further in and has been working well.

I would definitely recommend this layout, moving the rear shocks 6mm further in on the rear tower, removing the weight from the slipper and 30-50g under the lipo :)

mark christopher
29-07-2016, 04:45 PM
what chassis are you using alloy or carbon?

mrspeedy
29-07-2016, 07:22 PM
Alloy ..

AntH
29-07-2016, 09:57 PM
Try going for larger shock piston holes and up the shock oil wt. to compensate.

Sure laying the shocks over changes the rising rate a bit but mainly it's just making it softer. Easy option is just to use a softer spring. What's the weight distribution with the lipo forward and wonder how this compares with B6?

So, with the revised layout, I attended NEAM at Seaham on Sunday night. Its a all carpet with typical indoor features. On the flat, the car was very good, very sharp, without over rotating. A bit more lively than with the saddles in.
But we had some overlapped gym mats, and small moguls, which the back of the car was skipping about on too much.
I moved the shorty position further back, to stop the back skipping up too much, and this worked well.
I ran like this for the final few runs of the night, very happy with the cars pace ..... rapido.

I can't help but feel, that it'll be quicker with the shorty further forward though, if I can manage to somehow keep the rear in check over the bumps.

millzy
01-08-2016, 10:08 AM
Hi Dan/ Si,

Can you upload a photo of the rear shock tower pick ups?

I'm currently running my KF2 SE in mid conversion , this is different to your layout I know; however, I also have two extra inner holes on my rear tower. I find this works very well on low grip or blow out grass with 30-40g under a shorty or 80g under a LG lipo . Would be nice to get a comparison

ianjoyner
04-08-2016, 12:55 PM
Hi Dan/ Si,

Can you upload a photo of the rear shock tower pick ups?

I'm currently running my KF2 SE in mid conversion , this is different to your layout I know; however, I also have two extra inner holes on my rear tower. I find this works very well on low grip or blow out grass with 30-40g under a shorty or 80g under a LG lipo . Would be nice to get a comparison

are you running any rear weight with mid on grass? I find the weight too far forwards and wouldn't add anything under the LiPo in mid layout.

mrspeedy
05-08-2016, 03:30 PM
Hi Dan/ Si,

Can you upload a photo of the rear shock tower pick ups?

I'm currently running my KF2 SE in mid conversion , this is different to your layout I know; however, I also have two extra inner holes on my rear tower. I find this works very well on low grip or blow out grass with 30-40g under a shorty or 80g under a LG lipo . Would be nice to get a comparison


Sorry mate don't have a pic but the holes are in line with the existing ones, about 6mm in, and 69mm between centres, Works a treat ...

Ran mine for the first time properly on Sunday at the South West regional at Tiverton, sandy astro with bumpy and cut up grass sections.

I haven't gone well there for a few years now, never have enough steering or traction with the KF2 before ..

Wasn't a problem this time, had kit setup, apart from 1.7 x 3 rear pistons on 400 cst oil. All kit geometry, and diff.

Ran the car with the new forward weight, and stripped down slipper, 50gms under the lipo, staggers up front and yellow mini spike out back.

The car drove a dream !!!! tonnes of steering and enough traction .. even on the sandy bits !! Only change I made all day was to widen the rear track 3mm overall to gain a little turn in off power, and a little more on power traction ..

Gave me my best result for ages ... 2nd in the B final and hunting down 1st place .. just needed one more lap lol ...

millzy
05-08-2016, 03:47 PM
are you running any rear weight with mid on grass? I find the weight too far forwards and wouldn't add anything under the LiPo in mid layout.

Yes mate . 40g under the belt and 10g on the rear of the shock tower.

stuey
14-08-2016, 06:37 PM
Hi guys, a question if I may. I ran my KF2 SE for the first time today on a small very bumpy mixed astro track. It seemed to go pretty well, apart from a small steering assembly mishap...
At the moment I only have saddle packs, so I had to run it in the forward motor position. Having read this thread and not having tried anything else yet, how does my layout work compared to the low grip motor position and a shorty? I have the bits to run it forward motor and shorty like you guys apart from the 117 tooth belt, but at the moment I feel a little bit more weight on the rear would settle it down more, thats why I am thinking try low grip first. I have the shocks on the rear and a ball diff, the rear seemed fairly well planted but did break loose occasionally.
Cheers :)

paulc
14-08-2016, 07:47 PM
Sorry mate don't have a pic but the holes are in line with the existing ones, about 6mm in, and 69mm between centres, Works a treat ...

Ran mine for the first time properly on Sunday at the South West regional at Tiverton, sandy astro with bumpy and cut up grass sections.

I haven't gone well there for a few years now, never have enough steering or traction with the KF2 before ..

Wasn't a problem this time, had kit setup, apart from 1.7 x 3 rear pistons on 400 cst oil. All kit geometry, and diff.

Ran the car with the new forward weight, and stripped down slipper, 50gms under the lipo, staggers up front and yellow mini spike out back.

The car drove a dream !!!! tonnes of steering and enough traction .. even on the sandy bits !! Only change I made all day was to widen the rear track 3mm overall to gain a little turn in off power, and a little more on power traction ..

Gave me my best result for ages ... 2nd in the B final and hunting down 1st place .. just needed one more lap lol ...

When you've stripped the slipper down are you still using the Schumacher slipper spring or a differant brand

CARB
14-08-2016, 09:02 PM
hi I bet your track rod came off the swing arm, try putting a 3mm grub screw in from the top side so it locks the 3mm underside one, this way there is no need to lock tite the screws and they will never fall out again.

CARB
14-08-2016, 09:12 PM
Try taking the front alloy braces off, and just put 3mm nuts on where the stiffeners go, this seems to let the car have more twist corner to corner, I have found the car becomes much smoother in its feel and more consistent over a full to discharged battery run. if you have driven another make of buggy such as a YZ2 you will get the same feel, this is a reason the K2 has a high flex top deck.
it seems a symptom of the Schumacher as the SV2 was the better with more flex.

mrspeedy
15-08-2016, 03:54 PM
Hi guys, a question if I may. I ran my KF2 SE for the first time today on a small very bumpy mixed astro track. It seemed to go pretty well, apart from a small steering assembly mishap...
At the moment I only have saddle packs, so I had to run it in the forward motor position. Having read this thread and not having tried anything else yet, how does my layout work compared to the low grip motor position and a shorty? I have the bits to run it forward motor and shorty like you guys apart from the 117 tooth belt, but at the moment I feel a little bit more weight on the rear would settle it down more, thats why I am thinking try low grip first. I have the shocks on the rear and a ball diff, the rear seemed fairly well planted but did break loose occasionally.
Cheers :)

I couldn't say how it compares tbh as I've only run kit setup and the forward motor/shorty setup.

Between the setups I've run, moving all that weight forward the rear feels less lardy and the car feels quite a bit more agile ... even with a 50g weight under the lipo ..

I'd say the new inner shock hole is a must with this setup, as is the lightweight slipper ..

Apparently the B5 slipper spring works on this setup ..

I couldn't find one so I dug out a spring of my old RC10 Team car hydradrive setup ... circa 1991 :woot:

stuey
15-08-2016, 06:20 PM
Hi CARB, you guessed right on the steering link! I either forgot to threadlock those screws, or not enough. One bushing and bearing came out, and the other was loose. I did look around for them in vain. Then by a miracle one of the guys found all of the bits still together! Got it back together to run the rest of the meeting. I did put some threadlock on but the grubscrew locks are a good call :) I will try taking off the alloy stiffeners for a round and see what that does.

I have a couple of shortys and a 50g weight on the way now mrspeedy, so I can try it although I forgot the 117t belt. I would imagine a shorty right back and weight would have a more rearward weight distribution than just saddles on their own. I did move the rear shocks right in on the top and drop down to 30wt with kit pistons, which was better. The track is kind of a one off bumpy wise!

Cheers

CARB
16-08-2016, 08:09 AM
hi, Try changing the steering track rod location on the centre link, this smooths out the snap over steer mid corner which leaves you pointing at the inside track marker.
I run 1.7 three hole Pistons front and rear at mendip which has in places lots of micro bumps that really makes the suspension work hard and the option shock tops so that I can get all the air out and a consistent emulsion damper.

The car will keep you busy chasing a set up for sure, weather this is a good or bad thing I am not sure.
Neale

stuey
16-08-2016, 10:08 AM
Do you mean move the steering rod ball joints to the rear of the two holes on the centre steering link?

CARB
16-08-2016, 10:53 AM
Yes that right, nobody seems to use it but it does soften the steering

stuey
16-08-2016, 12:19 PM
Ok thanks I will try it out :)

stuey
16-08-2016, 07:01 PM
Now I have a couple of shorty packs, I thought I would measure the front/rear weight balance before deciding what layout to try. First I checked with my saddle packs in (all I had when building the car) and the forward motor position. I did the measurements a few times, so are sort of accurate. There is a small margin for error though.
Saddles/Forward motor F 42.3%, R 57.5% (1570 grams)
Shorty rear/Forward motor F42.8%, R57.1% (1540 grams)
Shorty rear with 40g under weight/Forward motor F41.9%, R 58.1% (1580 grams)
I thought the shorty with weight would be a bigger difference, not much more than 0.5%
I think I will give the low grip setup a try first which may suit me better to start, as I'm new to this type of layout.

stuey
03-10-2016, 08:09 AM
Hi guys. I ran my KF2 indoors for the first time on what is medium grip carpet. I started with the mid motor setup, 15000cst gear diff, shocks on the rear and 35g between the motor mount and diff housing. 7.5T motor, slipper as stock and probably not slipping enough. It felt a bit understeery but ok. Someone suggested that I move the shocks to the front of the rear wishbones, which made it more agile. The problem is I lost forward traction after a few runs on Minipin 1's, which made life a bit difficult. Other guys running 22-3, B6, YZ2 etc were managing a whole day on a set of rears, with some to spare and appeared to have loads of forward drive.
I have noticed that the static weight distribution with mid motor is pretty much the same as the other layouts, I was hoping the motor effect would help in that regard. I am a bit disheartened tbh, I am simply not up for using a set and a half every meeting when other cars are much kinder and just as quick if not more so. I am not sure where to go with the car layout wise now! Any advice please? :)

micholix
03-10-2016, 10:13 AM
Hi stuey,

Not knowing what you have set the rest of you car, i would try to set the rear as followed:
1* of anti squat
2.5* toe
And/or may go a bit lower on rear diff oil
Rear anti roll bar

Try one at the time

Hope that helps, or someone els can jump in too?


BR
Mike

DarkHawk
03-10-2016, 10:49 AM
If you would like Stewart I can give you my full setup that I used to run on a Thursday which was very competitive

Danosborne6661
03-10-2016, 11:08 AM
Now I have a couple of shorty packs, I thought I would measure the front/rear weight balance before deciding what layout to try. First I checked with my saddle packs in (all I had when building the car) and the forward motor position. I did the measurements a few times, so are sort of accurate. There is a small margin for error though.
Saddles/Forward motor F 42.3%, R 57.5% (1570 grams)
Shorty rear/Forward motor F42.8%, R57.1% (1540 grams)
Shorty rear with 40g under weight/Forward motor F41.9%, R 58.1% (1580 grams)
I thought the shorty with weight would be a bigger difference, not much more than 0.5%
I think I will give the low grip setup a try first which may suit me better to start, as I'm new to this type of layout.

I would suggest trying the shorty lipo forward, rather than in the rear position like you have it. For outdoor racing I run my shocks furtherest in on the towers all round, then when racing indoors I stand them up 2x holes all round to get some agility back.

What tyres also? You could go to cut staggers if you're only running staggers and as suggested above, increase the anti-squat if you'd like the car to rotate a little more.

stuey
03-10-2016, 11:10 AM
Thanks young man :)


If you would like Stewart I can give you my full setup that I used to run on a Thursday which was very competitive

stuey
03-10-2016, 11:14 AM
Hi Dan, the car is set up for mid motor at the moment (motor furthest back, lipo in front of motor housing) so I'm not sure on your first comment.
Tyres were Minipin 1 and 2 on the rear, cut stagger yellows front. I am trying to reduce the rear tyre wear during forward traction, side grip was fine. Cheers :)


I would suggest trying the shorty lipo forward, rather than in the rear position like you have it. For outdoor racing I run my shocks furtherest in on the towers all round, then when racing indoors I stand them up 2x holes all round to get some agility back.

What tyres also? You could go to cut staggers if you're only running staggers and as suggested above, increase the anti-squat if you'd like the car to rotate a little more.

DarkHawk
05-10-2016, 09:22 AM
Stuart can you photocopy a setup sheet for me so I can write my set up down for your Sunday

mrspeedy
05-10-2016, 02:54 PM
Try stripping the slipper clutch back to a basic slipper, ie spur gear and 2 pads only.

I run my KF2 with forward motor/forward lipo like this and its ace even in the wet !!

stuey
05-10-2016, 04:48 PM
Stuart can you photocopy a setup sheet for me so I can write my set up down for your Sunday

Will do :-)

stuey
05-10-2016, 04:50 PM
Try stripping the slipper clutch back to a basic slipper, ie spur gear and 2 pads only.

I run my KF2 with forward motor/forward lipo like this and its ace even in the wet !!

:thumbsup:

I have been thinking of trying this, what effect does it have on the car? The standard slipper setup is quite heavy and the rotating mass must have an effect, but not sure what tbh.

mrspeedy
05-10-2016, 06:54 PM
The effect of the stock slipper is a big kick of forward torque .. a bit like a 3 gear I suppose .. taking some of the weight out reduces that effect.

If you want to try it for yourself, take out the tranny with motor and all still attached, and fire it up while holding it in your hand .. it's quite surprising .. you can then take bits off and directly feel what effect it has .. thats what I did ... my final choice of a fully stripped down slipper was because that was the most neutral of all the options .. :thumbsup:

stuey
05-10-2016, 07:30 PM
The effect of the stock slipper is a big kick of forward torque .. a bit like a 3 gear I suppose .. taking some of the weight out reduces that effect.

If you want to try it for yourself, take out the tranny with motor and all still attached, and fire it up while holding it in your hand .. it's quite surprising .. you can then take bits off and directly feel what effect it has .. thats what I did ... my final choice of a fully stripped down slipper was because that was the most neutral of all the options .. :thumbsup:

So is it counteracting the torque effect of the motor, which in mid motor layout should be helping with rear traction? Or is it giving a big shove of forward torque, which would not be helping me with the wheelspin issue?

mrspeedy
05-10-2016, 09:32 PM
Its more than countering the effect of the motor, which won't help if you're suffering wheelspin and low rear traction ...

stuey
06-10-2016, 07:32 AM
That is very useful info, I will give it a try. Thanks Speedy :thumbsup:

bish
18-10-2016, 09:06 PM
So realistically, to race on dirt I'd need to take the slipper down to minimum plates? I'm already running MM, Ive managed to mount my Tekin RSX to the rear of the chassis (between side gears and dirt guard- it's not pretty wiring, but the weight distribution seems sound).
I'm hoping it'll work...