View Full Version : DB01 Dampers (non tamiya) advice
VinceVegaUK
05-07-2009, 06:27 PM
Hi all,
Sorry if this has already been mentioned, i did a search and looked through posts but couldn't find anything.
I went to my 1st Buggy race today at Bury. Everyone was friendly and helpful and I met a few guys i see at my other local track where we race touring cars and buggies.
http://myweb.tiscali.co.uk/vincedesign/images/Durga_01.jpg
There where only 10 racers, so we where split into two sets of 5. The first race was going well and i managed to nail the jumps a lot better than last weeks practice run, and it got better each race. Had a few teething issues, my overclocked 7.2v servo wire came off so lost steering but luckily just after the line. Second race i won but again just after the line my pinion fell off :-s. I have found the hop up pinion set (13t, 14t, 15t) are a little longer than the stock ones and the grub screw is very near the end of the motor pin. the last two heats i won also so i was 1st in the B final :-)
In the final i did ok but found the car across all races a bit soft with the stock dampers, the tyres gripped well but with this combination i was bottoming out a lot and grip rolling if i didn't keep myself on my toes or pushed too hard. I came 2nd in the B final so was please but felt if i hadn't have rolled (3x) so much by pushing it I could have won.
Does anybody have any tips on a good damper set and a spring set thats good with the db01? and what oil do you suggest, the stock oil is 900 weight but i have found most of the club guys are running with 30/40 with harder springs. The TRF ones are a little pricey, the 3 racing ones are cheep but look a little too cheep, i hear you can use the Team Associated or Losi ones, if so has any one used these?
Thanks
VV
grab a set of B4 shocks, silver springs all round, 35wt front and 30wt rear, and keep the B4 piston setup, be sorted then
VinceVegaUK
05-07-2009, 06:35 PM
grab a set of B4 shocks, silver springs all round, 35wt front and 30wt rear, and keep the B4 piston setup, be sorted then
I take it thats the Team Associated B4 is there a difference between the 4wd & 2wd TA B4 dampers? Just making sure.
Any recommendations on where to purchase?
Thanks
VV
EDIT
Looking on online shops am i looking for the RC10B4 'shocks' as the americans call them, i cant see them in a set so do i have to buy them all individually? Im looking at the tamiya ones now but there a lot at £47, does the 501x spring set fit with the stock plastic dampers?
peetbee
05-07-2009, 06:59 PM
Keep an eye out for a secondhand set of shocks on here (or a wanted advert) they often turn up for around £25 the set.
You can buy them as a set I believe, but does work out pricey, mind you, not as pricey as the Losi shocks!
(B4 = 2wd B44 = 4wd)
PS I run old non threaded Losi shocks and they work great, based the setup on the advice of DCM above
superdez
05-07-2009, 08:26 PM
tower hobbies in the states
great value and shipping is quick
VinceVegaUK
05-07-2009, 09:49 PM
tower hobbies in the states
great value and shipping is quick
I had a look at tower hobbies http://www3.towerhobbies.com/cgi-bin/wti0005p?&I=ASCC9525&P=X and only found the fronts, do i have to order each part sepratly? if so it comes to $54, i can get the TRF set (inc all 4) ones for $70 :-s. Not sure about getting second hand ones as dampers get punished and if they break i have no comeback!
stox217
05-07-2009, 10:21 PM
Every now and then new one's come up on here but you will have to wait a while
superdez
06-07-2009, 12:05 AM
I had a look at tower hobbies http://www3.towerhobbies.com/cgi-bin/wti0005p?&I=ASCC9525&P=X and only found the fronts, do i have to order each part sepratly? if so it comes to $54, i can get the TRF set (inc all 4) ones for $70 :-s. Not sure about getting second hand ones as dampers get punished and if they break i have no comeback!
http://www.m-k-racing.com/product_in...oducts_id=5008 (http://www.m-k-racing.com/product_info.php?products_id=5008)
B44 front shock kit from M-K Racing, £37
http://www.m-k-racing.com/product_in...roducts_id=705 (http://www.m-k-racing.com/product_info.php?products_id=705)
B44 rear shock kit from M-K Racing £39
sosidge
06-07-2009, 08:01 AM
At those prices, I would go for the Tamiya set, combined with AE springs (or even the kit Durga springs). Tamiya's own springs are very soft for UK conditions, I think the Tamiya blue front is equivalent to the AE Silver front, and they get softer from there.
The Tamiya shocks are basically a metricised copy of the AE ones, but a direct fit on the car, and easier to work on. Start with 1.4mm rear piston and 1.3mm front piston.
Your bottoming out etc. is more a function of the very short travel on the Durga kit shocks, with the Tamiya shocks you get a lot more travel (they do need spacers in them otherwise you get far too much travel), you'll find that the car is a lot more settled with the longer travel dampers. Also the plastic dampers have ineffectual pistons (hence the #900 oil). They just aren't up to proper racing.
shanks
06-07-2009, 12:21 PM
Hi all,
Sorry if this has already been mentioned, i did a search and looked through posts but couldn't find anything.
I went to my 1st Buggy race today at Bury. Everyone was friendly and helpful and I met a few guys i see at my other local track where we race touring cars and buggies.
http://myweb.tiscali.co.uk/vincedesign/images/Durga_01.jpg
There where only 10 racers, so we where split into two sets of 5. The first race was going well and i managed to nail the jumps a lot better than last weeks practice run, and it got better each race. Had a few teething issues, my overclocked 7.2v servo wire came off so lost steering but luckily just after the line. Second race i won but again just after the line my pinion fell off :-s. I have found the hop up pinion set (13t, 14t, 15t) are a little longer than the stock ones and the grub screw is very near the end of the motor pin. the last two heats i won also so i was 1st in the B final :-)
In the final i did ok but found the car across all races a bit soft with the stock dampers, the tyres gripped well but with this combination i was bottoming out a lot and grip rolling if i didn't keep myself on my toes or pushed too hard. I came 2nd in the B final so was please but felt if i hadn't have rolled (3x) so much by pushing it I could have won.
Does anybody have any tips on a good damper set and a spring set thats good with the db01? and what oil do you suggest, the stock oil is 900 weight but i have found most of the club guys are running with 30/40 with harder springs. The TRF ones are a little pricey, the 3 racing ones are cheep but look a little too cheep, i hear you can use the Team Associated or Losi ones, if so has any one used these?
Thanks
VV
Looked pretty good to me pal - you certainly hustled it round the track well enough considering the way it was handling!
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.