PDA

View Full Version : rear drop


restimax
06-07-2009, 09:48 AM
in the cat, what the best mod to have more drop at the rear?;)

Swiss
06-07-2009, 09:55 AM
I use the turnbuckle rod ends instead of the std short ones on the bottom of the shock. And a 3/4qtr one on the front.

P

mikeyscott
22-09-2009, 06:04 PM
I'm looking at doing this too.

How many people are running with the different cups?

bigred5765
22-09-2009, 06:32 PM
we have always run them its worth doing,and try to run as small amount of washers at the rear to lift the wishbone high,

mw02veg
22-09-2009, 06:44 PM
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

mikeyscott
23-09-2009, 04:31 PM
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

.75 of an inch then on the rear shocks?

discostu
23-09-2009, 10:20 PM
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

hey mike

how much weight is grant running

bigred5765
23-09-2009, 11:26 PM
we run about the same weight.108grms if i remember right,

eichkay
24-09-2009, 12:03 AM
we run about the same weight.108grms if i remember right,

Im rather new to the schey, where is the weight located ? front bia's, rear bia's ... 50/50 ?? also is this weight to make the car legal at the events or required for better handling ?

MHeadling
24-09-2009, 07:52 AM
What's the part number for the 3/4 lengh ball links ?

I'm interesed as to what weight the the team run too?

niggs98
24-09-2009, 08:07 AM
there isnt a 3/4 lenth ball joint. get the longer ones for the turnbuckles and cut them to the desired lenth

Mossy
24-09-2009, 08:13 AM
Nath is right, just cut them down to the correct size. As for weight, for me it varies depending what track im at. I know Grant is pretty steady around the 108g mark, but at Worksop and the Euros i didnt run any. I prefer a more lively car than Grant, so comes down to what you like really.

Positioning the weight, when I don run some its under the chassis as central as possible. The weight distribution on the car is fine so no need to run it to the front or back.

Si

mikeyscott
24-09-2009, 09:00 AM
there isnt a 3/4 lenth ball joint. get the longer ones for the turnbuckles and cut them to the desired lenth

Ah ok, I'll look into that, need to get out the measuring tools..

Think it's .75 for the full length ones.

Surprised they haven't released new cups as option parts etc.

bigred5765
24-09-2009, 09:42 AM
for positioning on Matty's car i never move it, but as Si said we did remove ours for the euros,but back in the UK we haven't removed it yet but we also haven't run ares indoors yet, ill attach a pic of ours,it'll have to be a bit later flat battery:thumbdown:

Northy
24-09-2009, 10:13 AM
"ours" ;) :p:p:p:woot::woot::woot::thumbsup::thumbsup::thumb sup::):):):):wub:wub:wub

Love you Lion-o

bigred5765
24-09-2009, 10:26 AM
"ours" ;) :p:p:p:woot::woot::woot::thumbsup::thumbsup::thumb sup::):):):):wub:wub:wub

Love you Lion-o

corrected SIR,

mikeyscott
24-09-2009, 01:20 PM
Measured the ballcups and the turnbuckle ones are about 19mm and the standard ones are about 14mm.

3/4 of the turnbuckle ends is 14.25mm

niggs98
24-09-2009, 02:04 PM
not quite..... as you have long and short there make the 3/4 ones half way inbetween ie aprox 16.5-17mm

bigred5765
24-09-2009, 03:46 PM
just measured mattys ball joints for ya mikey,
long =19mm
3/4 = 16.5mm
short = 14mm

mikeyscott
24-09-2009, 04:06 PM
just measured mattys ball joints for ya mikey,
long =19mm
3/4 = 16.5mm
short = 14mm

Cheers :D