View Full Version : TRF511 2009 euros winning setup
jimmy
20-08-2009, 09:05 PM
Here's the winning setup from the 2009 Euros. This is Hupos setup - which is the same for the other guys cars including eventual winner Marc Rheinard, since hupo setup all the cars like his.
http://www.oople.com/rc/photos/euros2009/hupo511.jpg
jimmy
20-08-2009, 09:08 PM
Man, that setup sheet sucks - I need to design a new one with all the options on there :thumbdown:
never mind... I think they guys also ran 12 degree alloy front hub carriers. Hupo ran the new flex topdecks but the other guys ran normal. All the drivers ran the new grey ball cups. Think that's about it.
trf14
21-08-2009, 08:24 AM
Jimmy , what kind of inserts did they used?.. Any idea of the shock lengths ( limiters or not and how much)
Great report by the way.... sorry SUPER EXCELLENT report :thumbsup::thumbsup::thumbsup:
Do you have also HUPO's 2WD set-up ?
Cheers
jimmy
21-08-2009, 08:28 AM
I don't know what he settled on, he had some trishbits and some edit foams - not sure what the guys ended up with.
Actually, I do have the winning B4 setup also: using Tamiya shocks and Trishbits hopups.
http://www.oople.com/rc/photos/euros2009/hupob4.jpg
djmcnz
21-08-2009, 11:32 AM
What springs are they using? My Tamiya option springs are all white in colour but the sheets above imply that "Tam" springs are available in actual colours to match their strength... the all white scheme is really, really dumb IMHO.
The 3 grades of Tamiya springs are all white, but have either Red, Yellow or Blue dabs of paint on the tops of them. Hard to see, especially if they have rubbed off. I use permanant marker pens to mark them better.
DaveG28
21-08-2009, 01:44 PM
Wow, really surprised at how hard they ran springs wise actually, how much lead were they running, any idea Jimmy?
jimmy
21-08-2009, 01:50 PM
I didn't see any - but I'll have a look at the photos I got
bombman
22-08-2009, 06:19 AM
What kind of tires they used in the Euro?
I thought Schumacher, but they wrote HA.
Guy.
Chris
22-08-2009, 05:09 PM
I didn't see any - but I'll have a look at the photos I got
Jimmy, could you post the photo's of the 3 TRF cars
And is the tech chart available of the 4WD A final?
suparajicon
27-08-2009, 09:15 PM
Does any one knows which are those white ball studs Hupo was using ?I wonder if it's Losi's or RPM ones. I would like to try.
T4miy4 Guy
27-08-2009, 10:38 PM
Just out of interest! these setup`s are the drivers setup`s for the designed course/track! so how would they benefit anyone else? I understand the fixtures and fittings side but buggy setup is surely from testing the track / surface and setup so the buggy handles well for its enviroment/bumps/ramps/camber etc... is this just an interest thing or am i missing something?
<<<< total boon! Andy ;)
jimmy
27-08-2009, 10:47 PM
Helps anyone going to race at THAT track of course - and generally applies to similar high grip bumpy tracks. If you're racing on a smooth dirt track in the USA then there's very little interest - I'll be copying this setup to try it that's for sure.:thumbsup::thumbsup:
Just out of interest! these setup`s are the drivers setup`s for the designed course/track! so how would they benefit anyone else? I understand the fixtures and fittings side but buggy setup is surely from testing the track / surface and setup so the buggy handles well for its enviroment/bumps/ramps/camber etc... is this just an interest thing or am i missing something?
<<<< total boon! Andy ;)
Like Jimmy said, on a similar track, it would get you in the ball park, setup wise, but if it isn't a similar type of track, just a curiosity thing.
shanks
28-08-2009, 11:19 AM
Just out of interest! these setup`s are the drivers setup`s for the designed course/track! so how would they benefit anyone else? I understand the fixtures and fittings side but buggy setup is surely from testing the track / surface and setup so the buggy handles well for its enviroment/bumps/ramps/camber etc... is this just an interest thing or am i missing something?
<<<< total boon! Andy ;)
Does it matter to you anyway? from what i hear you would have to put the theory in reverse???
A little (well ok quite plump) bird tells me you tend to drive the wrong way around tracks anyhow!!!!!! :p
T4miy4 Guy
28-08-2009, 01:00 PM
Does it matter to you anyway? from what i hear you would have to put the theory in reverse???
A little (well ok quite plump) bird tells me you tend to drive the wrong way around tracks anyhow!!!!!! :p
Right! thats Shanks soon to be added to my list!!
:p
CraigM
14-09-2009, 12:16 AM
Does anyone know what motor timing and ESC profile Hupo uses?
Chris
21-09-2009, 08:46 PM
Does anyone have info about the shocks the TRF guys used @ the euros?
-how many o-rings? (I know Jilles used 2 blue o-rings in every shock, but he was not at the euros;))
-blue, clear or red o-rings?
-limiters front and rear?
-machined pistons or molded?
DaveG28
04-10-2009, 05:05 PM
As a note to anyone trying this setup, you either need to do it with the rear diff low (not high as in the manual) or add several mm of limiters to the rear shocks above the kit manual limiter, I did a cvd pin, outdrive and scratched all the bulkheads at the back today finding that out!!
B44&501xRacerEX
27-01-2010, 05:43 PM
Hum, I put new parts on my 501x getting it ready for next months race.
However I'm uncertain if Hupo's 511 setup will work on my car.:yawn:
Jimmy do you happen to have his old 501 setup? I need a setup for high traction clay.
I tried 35 wt in the front and 25 wt in the rear and that worked ok. But I'm thinking 35wt all 4 corners would be even better.
I have been using associated shock oil the clear kind.
jimmy
27-01-2010, 05:48 PM
Hey mate, Hupos Euros winning car setup from 2007 on clay is here:
http://www.oople.com/rc/photos/euros2007/setups/TRF501X_HubertH%f6nigl_2007EC-Vaasa.htm
it's linked with another from mike west in the race report from that event.
:thumbsup:
B44&501xRacerEX
27-01-2010, 05:50 PM
Thanks Jimmy.:thumbsup:
4wdfull
15-03-2010, 02:06 AM
Does Jimmy or anyone know what the equivalent rear camber link (upper control arm) geometry would be with the plastic rear hubs for the Euros set-up?
Also Does anyone know how many rear damper limiters are required to run that set-up? Thanks in advance.
TonyV2382
30-03-2010, 10:14 PM
I dunno all these setup are driving me insane...I think Im going to try the stock setup on the 501x WE and go from there. Ive always used 35F and 30R for oil but the pistons up front are smaller so maybe 30WT all around may be better. I will be using the AE springs though.
Which pistons are you using?
Welshy40
31-03-2010, 08:28 AM
What pistons were they running as i have no number four pistons?
TonyV2382
31-03-2010, 03:12 PM
Which pistons are you using?
3's up front and 4's in rear
Welshy40
31-03-2010, 04:24 PM
3's up front and 4's in rear
Tamiya do 1,2 & 3 so what make are they using as it isnt tamiya.
Piman
31-03-2010, 04:37 PM
Tamiya do 1,2 & 3 so what make are they using as it isnt tamiya.
Yes it is. The standard setup kit items are 3 & 4. The 511 comes with 3-5 on the piston tree (item 51281).
James
3's up front and 4's in rear
2x1.3mm (3) in front and 2x1.4mm (4) in the rear?
AaronR
31-03-2010, 06:22 PM
or
#3 Tamiya piston would be Option item 53977... http://www.tamiyausa.com/product/item.php?product-id=53977
#4 piston would be Option item 53978... http://www.tamiyausa.com/product/item.php?product-id=53978
3's up front and 4's in rear
or
#3 Tamiya piston would be Option item 53977... http://www.tamiyausa.com/product/item.php?product-id=53977
#4 piston would be Option item 53978... http://www.tamiyausa.com/product/item.php?product-id=53978
I was talked about it :)
Welshy40
01-04-2010, 11:08 AM
At the moment I'm starting to dislike Tamiya again (this time its not the bad quality plastics like before) due to this confusion.
When you get a kit the pistons with all manufacturers are piston 1, 2 and 3 so why have Tamiya got 3, 4 and five? Its really daft.
So then what pistons did Lee use at the Petit event as he used number two all over, unless that means the second (middle) piston in the kit. Does anyone know.
TonyV2382
01-04-2010, 06:43 PM
no...my kit came with 3's and 4's (501x wce)...so I put the 3's up front and 4's in the rear but I also ordered more separately and also have 1.2's. Im assuming the 3's=1.3 and the 4's=1.4
B44&501xRacerEX
01-04-2010, 10:25 PM
Tony:
WHERE IS THAT CLAY SETUP?
Hey mate, Hupos Euros winning car setup from 2007 on clay is here:
http://www.oople.com/rc/photos/euros2007/setups/TRF501X_HubertH%f6nigl_2007EC-Vaasa.htm
it's linked with another from mike west in the race report from that event.
:thumbsup:
It's this one, the one jimmy posted 2 months ago.:)
It's dated 2007 but still works well. Being 3 years old has nothing to do with it.
If not Aaron can surely help you out.
B44&501xRacerEX
01-04-2010, 10:32 PM
At the moment I'm starting to dislike Tamiya again (this time its not the bad quality plastics like before) due to this confusion.
When you get a kit the pistons with all manufacturers are piston 1, 2 and 3 so why have Tamiya got 3, 4 and five? Its really daft.
So then what pistons did Lee use at the Petit event as he used number two all over, unless that means the second (middle) piston in the kit. Does anyone know.
Has anyone tried the kyosho pistons? I heard they fit.
But's it's probably not a good idea, just a thought.:bored:
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.