PDA

View Full Version : Schumacher Cat Sx Spur Gear meshing problems


Brooks
09-09-2009, 02:19 PM
Hi people

Have been having probs tyring to mesh the standard spur with a 22 pinion.

At one point i think its meshed, then you turn the spur again and the pinion is either too tight on the spur or so loose that the motor with shread the Spur as its too far away. :mad:

It doesnt look like the spurs are total round :confused: :confused: :confused: :confused: :confused:
I replaced one with another and it was the same

Has anybody had these problems

Cheers
Chris B

jim76
09-09-2009, 02:28 PM
check your motor is in the motor mount squarely.

lochness42
09-09-2009, 02:31 PM
Also check your front motor plate - one of my runs was ruined by loose motor plate resulting in stripped spur.

_sleigh_
09-09-2009, 02:36 PM
I'd probably start with checking the layshaft isn't bent

super__dan
09-09-2009, 03:28 PM
Or that the layshaft bearing hasn't collapsed

bigred5765
09-09-2009, 03:36 PM
check all of the above all good suggestions, but also make sure the spur gear hasn't slightly melted from slipping to much and made the center hole to big?

jim76
09-09-2009, 03:55 PM
i was going to suggest that, but then realised he'd already swapped the spur and still had the problem.
Move to B4 spurs if you can, get the layshaft altered.

James
09-09-2009, 03:55 PM
Check:

Rear gearbox housings arent tweaked
Layshaft bearings are ok
Layshafts straight
Motor Clamp hasnt twisted motor - or the sticker on the motor hasnt been 'ruffled' when clamped

Bigger spurs seem to mesh better on my car eg 84/23 on a 6.5 is what i ran at RHR national

Brooks
09-09-2009, 06:09 PM
thanks alot people :thumbsup:

Will check all that tonight and let you know

Brooks
09-09-2009, 08:51 PM
I checked the Layshaft bearings and they were ok and the Layshaft was straight :thumbsup:
Motor Clamp hadnt twisted motor and checked the motor bearing and they were fine :thumbsup:

Tyred meshing it again and it did seem better but still hard to get it the right meshing all round :bored:

James
09-09-2009, 09:35 PM
Mines a bit like that, its hard to tell if the bearings have gone too, maybe change them as a matter of course next time you do a strip down..
Good luck :)

Brooks
15-09-2009, 08:26 PM
Seems worse now, have taken the layshaft apart again, fitted a brand new one and its even worse :cry:

The motor meshing goes from out to in

Help Again People :cry: :cry: :cry:

niggs98
15-09-2009, 08:33 PM
daft question, have you tried a different motor to make sure the armature isnt bent ??

jim76
15-09-2009, 08:36 PM
or rebuild the whole rear end to make sure the gearbox sides haven't been moved in a shunt? You can check them to make sure they aren't buckled slightly also while they are off the car.

Brooks
15-09-2009, 08:48 PM
Will check that :thumbsup:

I did try a different motor and it was the same problem :cry:

Dazzler
15-09-2009, 09:13 PM
Did you say you replaced the layshaft or was it the spur you replaced? I was just wondering if the layshaft had been reduced in diameter to accept the AE spur that some people are fitting. If it has and then you are fitting an original Schumacher spur, it may not be located concentrically. You'll obviously know if the layshaft is standard or not if you have owned the car from new...
Check the location of the spur on the shaft to ensure a good fit, maybe mark the high and low spot then remove the spur and measure from the bore diameter to the spur outer diameter with a vernier calliper (if you have one) at both the high and low spots previously marked up. I can't see a tweek or similar causing what you are describing, only something that rotates and is bent or out of concentricity will cause it.

One things for sure, when you do eventually find out what it is, it'll be obvious i'm sure! Good luck.

MALLET
15-09-2009, 09:30 PM
I'd change your bearings as James has said

lochness42
15-09-2009, 09:40 PM
If you've got someone with Cat somewhere around you should try to swap part after part and find out what is causing problem. That will be cheapest and easiest way.

Mossy
16-09-2009, 07:22 AM
If your coming to the F3s ill take a look if your still struggling.

Si

DCM
16-09-2009, 07:37 AM
if you are suffering from loose/tight mesh, then that is something rotating out of true, so if you had bent housings and what not, it wouldn't do that. I would concentrate on the layshaft and slipper assembly.

Take the slipper off, and rotate the drivetrain, and see if there is any deflection on the layshaft, if there is, either it is a bearings or the shaft. If there is no deflection, assemble the slipper, one part at a time, and see what pulls it out of line. I would also strongly advise on checking to see if the spur gear alone, rotates true.

Brooks
16-09-2009, 08:15 PM
I did replace the Shaft and the spur with new parts

So you dont think the rear end would have tweated then????

discostu
16-09-2009, 10:12 PM
you would know if a bearing had gone it would move and be noticable if you have that much difference in mesh i cant see the problem being a bulk head or a tweak in the chassis as it would still run true but not square (in line) it sounds to me to be a layshaft or spur to be at fault have a look at the idler gear to see if that runs true if not i would put it down to the layshaft.