Ultima RB5 Setups

[jimmy]

Sticky thread for posting RB5 setups :)

[Phil_F]

I would like to get this thread started, here is a jpeg of the box stock setup. This is a low res scan. I also scanned in a blank setup sheet for those who would like it. Maybe it will help get some setups out... who knows.
Link to blank setup sheet.

http://farm1.static.flickr.com/238/515457116_693cedcc9a_b.jpg

[woOdy]

Sorry guys but I dont have a set up for you yet but I would like to say I had a good day at Bury Metro yesterday. I won. Qualified second behind Danny Mcgoo and I thought that was good. I did stuggle from the wet as it was pretty much the same as everybody elses( crap ). When it started to get a bit dryer then I started to worry. I then got the B4 manual out and started to change a few things. I do think the shock towers from Atomic are a must and also some weight in the front. The car held up very well and I still think it needs work. I feel the pistons are still wrong but thats for testing. I am geting a race report together for Jimmy so you will all have to wait for it.

[ThePromise]

Hello,

could anyone give me a link or an url where I can buy the Atomic Carbon shock towers for the RB5?

Thak you very much,

Chris

[jim76]

they aren't officially produced yet, but Jonathan has a template to make them as an adhoc item. If there is enough interest in them he will hopefully "mass" produce them as a stock item so they will be slightly cheaper.

www.atomic-carbon.co.uk (http://www.atomic-carbon.co.uk)

[bender]

Below is a link to my RB5 setup from todays 2007 Qld (Australia) Championships.

Finished 3rd - and very happy with the car.

http://web.aanet.com.au/fir/bender/Manuals_Setups_files/RB5_2007QldTitles.pdf

[ThePromise]

Below is a link to my RB5 setup from todays 2007 Qld (Australia) Championships.

Finished 3rd - and very happy with the car.

http://web.aanet.com.au/fir/bender/Manuals_Setups_files/RB5_2007QldTitles.pdf

Hello,

how did you manage to fill in the sheet on your computer?
I just get pdf-files I can't fill in anything.

Regards, Chris

[bender]

Hello,

how did you manage to fill in the sheet on your computer?
I just get pdf-files I can't fill in anything.

Regards, Chris

You need to download an editable blank set-up sheet. I have made a few for different cars on my website, but the one I used for the RB5 Ultima was made by Alexander Mach - which he graciously allowed me to host on my site.

You can download it here: http://web.aanet.com.au/fir/bender/Manuals_Setups_files/editable_blank_rb5.pdf

You can then fill it out and print it - or store it as a PDF file if you have a virtual PDF postscript printer.

To do that you need to install Ghostscript from this link:
http://mirror.cs.wisc.edu/pub/mirrors/ghost/AFPL/gs853/gs853w32.exe

and then the free PDF Fill tools from this link:
http://www.pdfill.com/download/PDFill_Unicode.msi

[Arn0]

Here are some setup about the RB5 (http://www.petitrc.com/setup/kyosho/SetupSheetsKyoshoUltimaRB5.html)

It is a bit wildly linked right now, something more refined 'll come late!

[caneye]

Odd. the PetitRC link is no longer working ..

[SimonW]

Here's my starting set-up for astro turf, HTH.(Stotfold and Eastrax)

Front: Silver 70#(zx5) spring
35wt (ae) 2C piston
Middle hole on tower, inside on arm
Inner link middle +1mm shim, outer link, inside hole
1 Deg camber 0 Deg toe
10g under steering rack and 15g squeezed into the bulkhead
30 Deg kick up no shim, hubs forward
Schu'r yellow spikes outside row cut off (leave them on if you like your car 'sharp')
Alloy axles fitted, all else as kit.

Rear: Light yellow 65#(zx5) spring
30wt (ae) 2B piston
Inside on tower, inside on LA243 arm (wide conversion BUT with kit shock shafts)
Innerlink inside +1mm shim, outer link outside hole + 1mm shim
Forward Susp' mount flipped for 1 Deg of Anti-squat, 1 Deg camber
Hubs spaced, Middle, Alloy hex's fitted
Schu'r yellow spikes

Other: Kit body and wing (mounted with flat shims not angled either way)
Battery forward, PT on servo
20/78 for a checkpoint 10x2
Ni/Mh 4200 batts
Lots of Ti screws in the back of the car only
PHEW !

[RogerM]

My base set-up from Coventry on a very grippy day. ......

Often go to the silver #70 spring on the front but otherwise no change much now....

http://i266.photobucket.com/albums/ii250/Roger_Mills/RB5_Cov_Feb08.jpg

[SimonW]

4 mm under the rear inner ballstud, surely that is almost falling out ?

[RogerM]

The stock ball stud has 10mm of thread, as do the Yokomo parts I have replaced them with (as they have a 2mm hex to aid quick changes). That means there is 6mm still in the mounting boss, which is fine.

[erkan]

roger put up a picture of those yokomo thingies =)
changing the inner ballstuds for rear upper arms are :thumbdown::mad:

[RogerM]

The part numbers you are looking for are

ZC-206MH 6mm thread
ZC-206LH 10mm thread

You will need to use US sized ball cups ...... I have the Losi whites on my car

I am shocking with a camera ..... trust me you will only be more confused if I post one of my calassic fuzzy thumb pictures!!!!!!

[erkan]

i got some black rpm 4-40 cups laying around :D
are those kind of ball studs with a hex in the top of the ball?

[RogerM]

Yes mate ......... only reason for fitting them as the K' ball studs are good other than that point

[Arn0]

Don't know how many of you guys still running the RB5 but here come a setup on grass track (http://www.petitrc.com/setup/kyosho/setuprb5/RB5_ArnaudCollet_RegionalGargenville20080511.pdf) (pdf).
I hope that may help!

[RogerM]

Ok .... off to make up my sheets ..... strikingly similar though ... really very close!!

[RSharpy]

Hi All, Please find below my set up from the F2's at Eastrax. A good starting point for any astro/multi surface track.

Please note with reference to 'Hole' settings count them from the inside of the car. And also that I have Atomic Carbon towers fitted.

Front

Oil- 32.5 wt Schumacher
Pistons- 2C
Spings- Silver (70)
Wishbone- Hole 2
Tower- Hole 3
Ride Height- Wishbone quite a bit below level
Camber- 1 deg
Inner link- Hole 2, no washer.
Outer link- Hole 1
Kick up- 30 deg
Weight- 35-40g in bulkhead/front end
Tyres- Sch Yellow mini spikes with outer row cut off
Inserts- None
Holes in wheels- 2x 3 mm

Rear

Oil- 25 wt Schumacher
Pistons- 2B
Springs- Blue (68)
Wishbone- Hole 2
Tower- Hole 4 (if using kit tower, use outer hole)
Ride Height- Drive shaft just below level
Camber- 1 deg
Inner link- Hole 3, 2mm washer
Outer link- Hole 2 4mm washer
Wheel base- Medium
Hex- 2mm washer between hex & wheel
Wing- Standard wing, centre on tower with 0 deg plate
Tyres- Sch Yellow mini spikes with inside and out side row cut off
Inserts- Schumacher Medium Green Inserts
Holes in wheels- 2x 6mm

Other Info

Cells- Orion 4200 SHO in centre position
Motor- Orion 6.5
Gearing- 21/Kit

For grass tracks my usual starting point is as above but 2.5 wt harder on the oil. Hole 1 on both the front & rear wishbones and up one on the springs all round, front L/green (75) rear silver (70)

HTH, Rich :)

[bondy]

Setup for Worksop please guys ??? Mr Sharp !

[RSharpy]

Setup for Worksop please guys ??? Mr Sharp !Unfortunatly I never ran mine at Worksop Mr Bond so can't really help there. But you could use my set up as a starting point. :)

[bondy]

Looks like were gona have to start from scratch !

[MikePimlott]

Any chance the Drivers who ran RB5's at worksop could post your fiishing setups for us all to look at.

Cheers.

[Fabs]

I can do better and give you karl's finishing setup...

Front: Light green #75 spring
30wt (ae) 2C piston
Middle hole on tower, outside on arm
Inner link inside +1mm shim, outer link, inside hole
1 Deg camber 0 Deg toe


Rear: Blue #68 spring
25wt (ae) 2B piston
Middle on tower, outside on arm
Innerlink outside + 2mm shim, outer link outside hole + 2mm shim
1° camber

All else kit standard. Karl wasn't completely happy with the car espeially the rear, and thought the silver springs as I ran in the finals would be a good idea to try.

[Robfo]

Where did you finish fab? :thumbsup:

[bondy]

well he was marshalling when I raced so not that good !! He HE !:o

[MikePimlott]

All else kit standard. Karl wasn't completely happy with the car espeially the rear, and thought the silver springs as I ran in the finals would be a good idea to try.

I ran silver #70 with 2B and 25wt on rear and it was "Loose" but controlable. I wanted to go down to blue #68 but didnt.
Got the worlds conversion to try for next time, but will play before then.

[Karl Marsden]

I ran silver #70 with 2B and 25wt on rear and it was "Loose" but controlable. I wanted to go down to blue #68 but didnt.
Got the worlds conversion to try for next time, but will play before then.


Hi Mike,

Thanks Fab for replying. As you may or may not know Mike I borrowed the car that morning from a very kind friend Robin Lucas, the Transmitter was kindly lended to me by Big Bond, and I have to say I can not comment on all the set ups just yet.

However, What I think was correct regarding the piston was that they were actually the 3B ones.

Now I should know, but I ran 25wt all round, as they felt stiffer than the kit 2B pistons fitted to Bond's car and Ian Robinson's.

Go kit, but with 30wt next time as a starting point. Use the out hole on the rear wishbone, and the stiffest springs. Silver Fab says :)

2mm under the front inner caber position, not 1mm.

If you run Lipo, weight the car up.

Hope this helps, and if not, come a say hello if I am there next time.

I have not raced off road for over 6 years Mike, and seriously for over 3, so I just think I ran out of time to be honest and coul dnot do everything I wanted to do in 1 day without no practise.

On the whole, the RB5 was excellent, easy to drive and I think yesterday's run is a good sign of the potential it has, and will hopefuly give more guys the confidence to go out and try one.

Most say it is more stable and easy to dive over the B4 who have changed, I think we have a car that will suit the majority of people, and I hope to see more around next time.

Best of luck with your racing

Regards
Karl Marsden

Kyosho UK

[Fabs]

Karl, I know you were using the 3 holes pistons but as you mentioned that kit setup would be a better idea that's what I put down.

On the rear end bit, you shortened the rear link, but wouldn't it be a better idea to make it longer and maybe flatter to help the rear end slide a bit mid corner?

[froggie]

well just got my Rb5 did the middle arm conversion. changed the factory diff balls and turnbuckles, The only problem i am having is getting the car to jump straight, Have tons of off power and on power stearing. Tons of traction,slight push still working on that. But wants to roll on jumps all the time still testing will post when setup is complete.

[niggs98]

Nathan Ralls worksop indoor setup

FRONT

oil 35 wt losi
piston 2c
spring lime green 75
shock tower kit middle
wishbone outer hole
inner camberlink middle hole +1mm washer
outer camberlink inner hole
hub height low (washers above)
kickup 25 degree's
weight 10g on top of servo
ride height wishbones below level


REAR

08 velvet body, kit shaft
oil 25 wt losi
piston 2b
spring mauve,blue (imt told 72 but not sure, spring that comes with the 08 rear end)
shock tower 08 middle
wishbone 08 inner
inner camberlink outer hole no washers
outer camberlink outer hole +2mm washers
08 hubs medium wheelbase (no height adjustment)
rideheight driveshafts level
wing in middle mount position

NOTES

shoulder cut off the front pivot balls for rear wishbones, 2 white washers placed behind wishbones to shorten wheelbase, car ran on nimhs but is normally on lipo with no additional weight (untill i check it on scales) cells in forward position
kit wing with half gurney (flies very neutral)

car very easy to drive with bundles of steering, fronts and rear minipins run full with mr O medium foams, when outside inner and outer row cut off the front, full rear with same inserts


any questions feel free to ask

[RogerM]

Looks very similar to my carpet set-up except

30g in front bulkhead, none near servo
short not super short wheelbase (will be changed for MK GP to see how it goes!)
Front springs losi black cut 1 1/2 coils
Rear springs losi blues (too stiff really but wanted stiffer than orange and didn't have silvers)
rear shock outer on stock tower (mid on Atomic tower I run) and out on wishbone, using 54mm shock shaft in rear (also the wider rear end but with normal length shocks and tower)

oils AE35wt all round

I am quite happy with this set-up at Dudley on all carpet (lapping about 0.1 off the fastest 4wd car in qualy which was a driver I should be competing with on level terms IMO). Will be going to Losi Silvers or Kyosho #80s (dark green) for MK GP as the slipper floor will require a little more rear roll. Might find I need even softer.

The key to the RB5 I found earlier in the year is not to run the front too soft .... basically forget the inner holes exist on the wishbones!


Basic outdoor set-up is similar to indoors other than Kyosho #70 (silver) springs all round and medium wheelbase + 2mm or so on ride hight all round.

The only problem I find with the RB5 is it's tendency to tuck it's nose in a little deep as you come off power, then only on carpet / ultra high grip ..... loverly everywhere else!!!!! Not being of national A final grade like nathan is I need a safer car so the stiffer front springs help there a lot. In fact I think that I have over compensated with the rear spring until I ran the stiffer fronts, might be worth dropping a rate or 2 on slippier surfaces.

[Pledger]

This was my setup at the first (middle-)Swedish indoor series: Hit me! (http://i210.photobucket.com/albums/bb236/CallePledger/Setupbofors-1.jpg)

What tires do you run with? I had problems finding the right front tires. I ran Schumacher mini pin in the rear. Tried mini pin in the front but I got a way to twitchy car. To much steering. The Proline 4-rib felt better when I found a setup with better steering but I still needed more steering. I am going to try Schumacher stagger. What do you think about that?

[RogerM]

We normally run Scumy mini pins on the front and rear (in yellow) and trim a row or two off if needed to calm the front end down. I don't think I've tried anything else indoors for a very long time!

[Phil Channon]

I have run my RB5 a couple of times at Oswestry, which is made up of carpet and wooden floor.
This is my current set-up.

Front.
35 cwt
2C piston
1.5 mm internal limiters
Neon Yellow spring
Inside hole of wishbone and no 3 hole on tower (AC)
Wishbones level
Camber link 2nd hole out on the inner mount (no spacers) and outside hole for the outer
25 deg castor
Running a brass bulkhead

Rear
25 cwt
3B piston
Nil internal limiters. But I'm running longer rod ends, to increase droop and also meaning the spring adjuster is not at the end of the shock body thread.
Blue (68) spring
Outer hole on the wishbone and no 4 hole of tower (AC)
Wishbones level
Medium wheelbase
Inner camber link in middle hole, nil spacers
Outer camber link on outer hole, 2mm spacer

Cells are run at the back
Worn schumacher mini spike (full) front and rear.

I find the car has plenty of mid and exit corner steering. It does hook its nose in if the power is taken off, but only on the high speed carpet section. I'm going to try a grade up on the front spring.

[RogerM]

Phil, great to see you running the RB5 too!!!!

I have found that running on the inner hole on the front wishbone is what causes the hook off power.
Try the outer wishbone hole mate, let me know what you think. Oh by the way, running the front shocks at 20mm top of rod end to base of seal cartridge in the outside hole.

Where did you get the brass bulkhead from?

[Phil Channon]

I got the bulkhead of Jim76, who I also got the car off.
I will try moving the front dampers, after the spring change.

[kyosho-viking]

so these last setups are still good for carpet?

my rb5 is on its way from the states as we speak:)

ordered schumis from models in motion on monday, but they still have'nt confirmed my order, any idea why? paid for with visa and everything.

[kyosho-viking]

anyone??

[RogerM]

I'm at work but will try to answer when I get back home. Depends on the carpet but I usually change the car more for carpet than any other surface, normally trying to stabilise the front end (losi black springs, cut 1.5 coils) and generate more rotation from the rear too.
For me carpet is the RB5s only weakness, it can be made to be very special on carpet but not on the "normal" off-road set-up!!

[Lee]

Special good or special retarded? :lol:

[kyosho-viking]

I dont know the english word for our carpet, but it's hard and about 3 mm thick with super high grip. if I directly transelate the name it would be something like this : "pinfelt carpet"

I run the new orion race spec BL esc and motor 6,5t and orion 3800 lipo's

In norway we run schumacher yellow cutted all around due to carpet life.



I also ordered tyres from models in motion over a week ago, and it is still "waiting" emailed them 2 times without any replies, should I try order from apex instead?

[Fabs]

I'd say use Nathan's setup from this week end's Petit RC race...

[kyosho-viking]

fabs: can I find it somewhere?

[Fabs]

I'm sure he'll post it soon, but it was very close to his worksop setup.

[kyosho-viking]

I would really like some setup tips :)

[niggs98]

hiya all have just seen this. my setup from the petit (from memory as the car isnt here at the moment) is as follows

FRONT

oil 40-45 wt losi dependant on temprature
piston 2c
spring lime green 75
shock tower kit middle
wishbone outer hole
inner camberlink middle hole +1mm washer
outer camberlink inner hole
hub height low (washers above)
kickup 25 degree's
weight 20g on top of servo 20 on top of square bit of the battery strap
ride height wishbones below level


REAR

08 velvet body, 54mm shaft
oil 30 wt losi
piston 3b
spring mauve,blue (imt told 72 but not sure, spring that comes with the 08 rear end)
shock tower 08 middle
wishbone 08 middle
inner camberlink outer hole no washers
outer camberlink outer hole +2mm washers
08 hubs medium wheelbase (no height adjustment)
rideheight driveshafts level
wing in middle mount position

NOTES

shoulder cut off the front pivot balls for rear wishbones, 2 white washers placed behind wishbones to shorten wheelbase, tekin 3400 lipo in forward position
kit wing with half gurney (flies very neutral)

car very easy to drive with bundles of steering, fronts have outside and inside rows cut off and rear minipins run full with mr O medium foams,
8g over weight limit

this setup is for high bite carpet with large jumps only as the oils are to thick for normal use. see setup on page 2 for normal use.

any questions feel free to ask

[RogerM]

very similar to mine for Newbury

only differences are rear inner camber link mid
wheelbase short
front oil 40wt AE
rear oil 35wt AE with 2b pistons

[Arn0]

I have Nathan'setup @ Petit, I've to put it clean with details and pictures to confirm previous nathan writing.
Most probably, that will be done for Saturday.

Nathan, thanks again for all the details you provide.

[RC_NILLE]

This is my carpet setup whit not many jumps. And the Ghea racing stuff gives the car a verrrryyyyy nice balance

Front:

Shocks: Light Yellow Springs, Piston 2B, Protech 500 oil
Shock Position: Arm outer, Tower middle

Camber-link: inner-hole chassis 2mm spacer, inner-hole in C-hub

Front Arms: 25 degrees kick-up, no plastic washer (higher rollcenter)

Options:
GHEA Racing brass bulkhead (GHEA8001) och 35gram lead in front.

Tires: J-Concepts Groovy

Rear:

Shocks: Light Yellow Springs, Piston 2B,Protech 400 oil
Shock Position:Arm inner, Tower middle

Camber-link: middle-hole chassis 2mm spacer, inner-hole Hub with 2mm spacer

Options:
Short rear tower with short shock housings, Worlds-kit,
GHEA Racings 1 degree brass Anti-squat block(GHEA8005),
GHEA Racings 2 degree brass toe in block (GHEA8003).

Tires: Schumacher mini-pin yellow (grinded down/Slicks)

5 cells in front position

[woOdy]

Just tried the Ghea rear tow in blocks to make it to 2 degrees. Wow. This make the car as fast as the rest at the top. All I need now is a good driver! :woot:

[Thomas P]

http://i123.photobucket.com/albums/o306/gabbax_74/Setups/RB5_skarpnackinne.jpg

[njc11]

My set up from Kidderminster BRC's (microsoft XPS Viewer..)

http://www.cls.eclipse.co.uk/RCSetUps/Nick%20Caro%20RB5%20Set%20Up%20Kidderminster%20BRC 's.pdf

Anyone know how else to save the editable set up sheets as either my own .pdf or even as a .jpg??

Cheers

Nick
:thumbsup:

[Arn0]

Hi Gentlemen,

Just to ket you know some change about what I do as their is some change to do on your bookmarks. Please refer to this message (http://www.oople.com/forums/showpost.php?p=45931&postcount=9).

Hope that help!

[RogerM]

My set up from Kidderminster BRC's (microsoft XPS Viewer..)

http://www.cls.eclipse.co.uk/RCSetUps/Nick%20Caro%20RB5%20Set%20Up%20Kidderminster%20BRC 's.pdf

Anyone know how else to save the editable set up sheets as either my own .pdf or even as a .jpg??

Cheers

Nick
:thumbsup:

Nick,

not far off what I run on the car. My only question is are you running extra weight to compensate for the Lipo???

[njc11]

Nick,

not far off what I run on the car. My only question is are you running extra weight to compensate for the Lipo???

Roger..

Nope, dont run any weight other than the Ghea bulkhead..

At the F345's i ran the same set up and it was awesome.. qualified A7.. In Rd4 i was on for TQ.. then he told me and i ended up up A2 lol..

I used to run 3B pistons all round with 30wt front and 25wt rear... did abit of reading up from Elvos guide and made changes for kiddy and the car did what i wanted it to do :)

Just need to sort the FS out now... not quite there.. not far off though..

U have a pm

Cheers

Nick
:thumbsup:

[karlst]

does anybody have any good set ups for the RB5 for FORCC track?

Ive got the fullspike tyres and wider front rims, just want to get the set up sorted now ready for my first trip there on Wednesday next week:eh?::eh?:

[niggs98]

does anybody have any good set ups for the RB5 for FORCC track?

Ive got the fullspike tyres and wider front rims, just want to get the set up sorted now ready for my first trip there on Wednesday next week:eh?::eh?:

try my epr one on this thread as a starting point
it will make my job easier when i get there. i believe ed and les at xtreme rc will have the correct springs for you

[karlst]

try my epr one on this thread as a starting point
it will make my job easier when i get there. i believe ed and les at xtreme rc will have the correct springs for you

thanks dude, so your coming then? LOL

[niggs98]

thanks dude, so your coming then? LOL

should be there but not promising

[karlst]

no probs mate, but i dont really want to be spending to much money on the RB5 as i want to get a B4 before the winter series starts, so the RB5 will be going......

so ideally i gotta race wednesday with what ever i have (a car with no spares) :thumbsup::thumbsup:

good luck to me :woot::woot:;)

[Neil Skull]

If you want to have a copy e-mailed, send me a pm with your e-mail address

[Hey Chris]

Can somebody point me in the direction of a blank set up sheet?

Cheers

[Arn0]

Can somebody point me in the direction of a blank set up sheet?

Cheers
http://www.oople.com/forums/showpost.php?p=45931&postcount=9

Nick, Rich and Shin setups from the petit are listed

[jaydits]

hi
we are racing the rb5 sp
did someone try the old rear brace so the rear toein is about 1 degree
we raced it on our last national on astro and the cornering speed was superb
even in the rain the car feld realy good
just wondering if other people use it
joey

[RogerM]

Something I'd looked at but actually doing it the other way around (ie. using the wider new front brace to reduce inboard toe-in) to create more rotation.

Again, anothrer useful tuning aid ... suprely the Kyosho cars have to be the most option rich chassis out there at present :)

[tmaxxlosixxx]

Please click one of the Quick Reply icons in the posts above to activate Quick Reply.

[tmaxxlosixxx]

im havin problems indoors on carpet it hooks front end round any advice im using associated springs all roundsiver on front 40wt oil and rear blue 25wt

[carlin]

im havin problems indoors on carpet it hooks front end round any advice im using associated springs all roundsiver on front 40wt oil and rear blue 25wt

Are you running long wheel base?
Also sometimes having to much sterring can cause this type affect have you tried turning your steering down?

[RogerM]

Ok, I need to see a full set up in order to be able to help you!

TBH indoors and carpet are not my strongest point as I only race indoors a couple of times a year but I can help. Post it up and I'll see what I can do.

First point will be that is an odd pairing on the springs!!!!

Try Kysoho lime green #75 on the front / 40wt 2C (shocks in outer hole on the wishbone ALWAYS!!) and Kyosho silver #70 / 30wt 2B on the rear kit shock locations and work from there.

Shortest link on the rear, 0mm under inner ball stud. Front link out on both bulkhead and hub, 0mm under inner ballstud.

I am sure Nick Caro has carpet setups as he races indoors alot over the winter.

[Arn0]

Hi Gents,

Roger, you are right; Nick get a couple of setup for indoor track, both carpet (http://www.petitrc.com/setup/kyosho/setuprb5sp/RB5SP_NickCaro_PetitRCRace2010/index.html) and sport hall floor (http://www.petitrc.com/setup/kyosho/setuprb5sp/RB5SP_NickCaro_WorksopRd320100103.pdf). The given links are the two latest from Nick on this type of surface.

It would be interesting to know which car you are using (RB5 or RB5SP), the tires (best guess is shuey mini pins yellow all around)... and so on. As said Roger, the whole setup!

[touringdriver]

looking for a good setup for indoor tight dirt track for my rb5 sp. i switched over to this car late last winter from a b4. really like it a lot better but just looking for a good starting direction. thanks.:D

[terrybmw]

i mainly race on carpet and astroturf what camber should i have on the front and rear as.i am new off road racing so any info would be much apreciated to give me a good starting point until i find my own set up that suits my driving.

[Anibal Henriques]

In portugal we are runing in two indoor tracks ,one in astro-turf and the other in carpet ,can any body give me a good setup point for this two type of track ,they are not bumpy ,very smooth they are,lost o jumps they have like table tops,whoops anda about 6 litle ones ,very working tracks .
My car is a RB5SP2 and im wondering if i need some wheight like the Rudebits ones to get a more satble car ?
Im runnig a 12delta GM motor with a GM80R Speedo.
Need a good setup,help me please.:rolleyes: