xx4 front shock towers

[bigred5765]

we all know that there is a shortage,
do you think theres enough people out there that would buy a machined alloy bottom brace. same shape as bottom half of the shock mount with a carbon top, same geometry etc,and does anyone fancy machining them or pre ordering them let me know your thoughts,
machinest out there that fancy this job pm me please

[trekkerkk]

me personally,
i think its a good idea as it crosses over xx4 x5
i would buy it

trekkker

[jimmy]

Sounds a good idea to me Carl. Losi seem to have dropped the ball a little with their support for this car and I don't even know why. Unless all the machines are busy pumping out toys at the moment?

[bigred5765]

heard two rumours
1 is mould has been dropped and broken
2 there dropping support for this / but i dont know what that means, ether new car or dropping 4wd

[tyreman]

Carl what your after already exists!

It's the Josh Cyrul conversion for the street weapon, from Trinity. It comprised of: lower alloy shock mounts front and rear and 3mm thick carbon plate towers that bolted to them.

[bigred5765]

were can i get em from brian

[Doomanic]

Unfortunately, those parts have been unavailable for years.:(

If anyone has a Street Weapon with them fitted, I'll pay good money for it.

[bigred5765]

yeh me too
brian over to you

[losixxx]

carl you are desperate to get one arnt you :D

makes me wonder how much my brand new old type graphite one is worth;) :D :D

[Funkymojo]

Would love have those alloy bits too...

[AndyM]

does any1 know how much they would cost to machine the aluminium parts? or to make the carbon ones?

[Doomanic]

If I can get a set to measure I can get the aluminium parts made locally. I cannot even guess at a price until the engineering company has seen the complexity of the parts involved.
Getting the carbon parts made is no problem at all, from past experience I would expect the towers to cost in the region of £10-15 each in 4mm carbon fibre.

[Chrislong]

If this is a fit and forget replacement for the fit and snap losi towers - count me in!

Might be worth designing into the lower mount - vertical ballstud mount?

Chris

[AndyM]

if i can find some1 to machine some for me, ill get some done.

just need to find some1 to machine them for me, any ideas?>
or any ideas in ways to maybe change it, like chris' idea about the vertical ballstuds

[matdodd]

count me in to

[Slimboyfat]

me too

[ashleyb4]

And me

[ashleyb4]

Surely if we got enough people to contact losi about it they will act. Another option is xfactory. Because they have none in stock which means they will need to get hold of some or get some made because soon they will run out then they will have to find an alternative and as the x5 is a new car i dont think they will be wanting to make a new car just yet. So if they run out of shock towers people will stop buying the x5 which results in profit loss.

A

[tyreman]

Surely if we got enough people to contact losi about it they will act.

If it was anything to do with the Losi 8ight buggy/truggy then maybe it would speed things up as thats whats selling at the moment, we are only a tiny sector of the market, compaired to 1/8th.
unfortunately:yawn:

[bigred5765]

thanks for all the replies guys I'm now convinced its worth doing,
i have contacted a very well know model engineering company thats looking into machining em,
he guessed at around 30 quid ish for the fit and forget alloy and around 4-6 quid for graphite bits in ether 3mm or 4mm carbon
don't take the 30 quid as gospel the more i get the cheaper. the less the dearer lol

[tyreman]

thanks for all the replies guys I'm now convinced its worth doing,
i have contacted a very well know model engineering company thats looking into machining em,
he guessed at around 30 quid ish for the fit and forget alloy and around 4-6 quid for graphite bits in ether 3mm or 4mm carbon
don't take the 30 quid as gospel the more i get the cheaper. the less the dearer lol

You watch Atomic Cabon muscle straight in on that one;)

[bigred5765]

good lets hope they do, anything to make racing cheaper is good in my mind go for it,and if some nice engineer can do it cheaper please pm me, you nice fella

[losixxx]

already asked him bri!! said he's too busy paaaaaa:D
what ever's made need to be designed to be able to incorporate the front anti-roll bar as well

[bigred5765]

o kk good point ill make sure its there

[tyreman]

I don't know why he hasn't done his own interpretation of the penguin front tower brace yet.:confused:

So get on with it JC.

[bigred5765]

penguin lol do explane brian please sounds interesting

[Doomanic]

It's the same idea as the Fibre-Lyte tower strengtheners (http://dcracing.co.uk/dcrshop/product_info.php?products_id=1353) I sell.

http://www.penguinrc.com/products/losi.html#xx4

[bigred5765]

ahh haaaa
a see

[super__dan]

Does it really need to allow the use of a front anti roll bar?

When I had my carbon braces made I did them especially to fit the roll bar and as a result they were an odd shape and quite ugly. I don’t know anyone that runs them now either? Because everyone makes them slightly differently you have to have a gap, exactly where you want the carbon for the strength. All I’m saying is Carl, consider if it’s really worth making them bigger and uglier ;)

[Cockerill]

Does it really need to allow the use of a front anti roll bar?

When I had my carbon braces made I did them especially to fit the roll bar and as a result they were an odd shape and quite ugly. I don’t know anyone that runs them now either? Because everyone makes them slightly differently you have to have a gap, exactly where you want the carbon for the strength. All I’m saying is Carl, consider if it’s really worth making them bigger and uglier ;)

Does that really matter on your car ;)

[_sleigh_]

ROTFPMSL

[OldTimer]

You watch Atomic Cabon muscle straight in on that one;)

What you saying Brian :D do you want me to send Wraggy across.

If Losi make some towers problem solved, but it would be nice to know the actual fact why there are no towers around at the mo ?.

[losixxx]

Does it really need to allow the use of a front anti roll bar?

When I had my carbon braces made I did them especially to fit the roll bar and as a result they were an odd shape and quite ugly. I don’t know anyone that runs them now either? Because everyone makes them slightly differently you have to have a gap, exactly where you want the carbon for the strength. All I’m saying is Carl, consider if it’s really worth making them bigger and uglier ;)

i know a few people who run front roll bar's...so do you dan;)

[MattW]

I'd be interested in some kind of solution - as my car currently has a broken tower on it (and ran that way all th rough Bury Metro national;) ) - as i have no spares!!

[bigred5765]

i started out on a solid works drawing, but I'm rubbish and need big help anyone fancy helping out ill do u a good deal on alloy parts machined

[ryan]

You got PM carl

[djduncaz]

http://www.kubli-racing.ch/index.html?lang=de-ch&target=d39.html

[losixxx]

i know there in short supply but £15.25 for a plastic front tower is crazy:D

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=130125429328&category=140979&ssPageName=ADME:B:EOIBUAA:UK:11

[tyreman]

There's 5 plastic and 5 graphite sat in my spares bag:p

[jim76]

i know there in short supply but £15.25 for a plastic front tower is crazy:D

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=130125429328&category=140979&ssPageName=ADME:B:EOIBUAA:UK:11


and the guy has more of them too!

[ashleyb4]

There's 5 plastic and 5 graphite sat in my spares bag:p


Hi brian my good mate you know i was only messing the other night.

:D

A

[losixxx]

Hi brian my good mate you know i was only messing the other night.

:D

A

something you 2 need to tell us about what your were upto the other night;) :D :D

[losixxx]

see a certain us shop has or had loads in this morning 17 when i ordered mine and within 10 minutes there was 1 left:D so looks like losi have sorted the problem just wonder how long it will take for some to arrive at horizon uk?

[ashleyb4]

something you 2 need to tell us about what your were upto the other night;) :D :D

:o :o

[bigred5765]

see a certain us shop has or had loads in this morning 17 when i ordered mine and within 10 minutes there was 1 left:D so looks like Losi have sorted the problem just wonder how long it will take for some to arrive at horizon UK?


i got mine at 2 Min's past midnight of him also

but they only found a few hidden in a storage bin some were so don't get Ur hopes up, the problem is still there,

[jimmy]

Sounds like a right farce - too busy pumping out toys to care or what? I think they described the XX4 as a 'limited re-release' didn't they?

[losixxx]

its say's on losi website they have always and will continue to support the xx4 and its still a current models.

ps

NIB xx4 graphite tower for sale £35:D :D ;) plus post

[cmgreen]

Does any one have any news on when they will be available again?

[jimmy]

its say's on losi website they have always and will continue to support the xx4 and its still a current models.

I see what it 'says' - it also says the XXX4 (xxx4!) outperforms all other 4WD buggies. ;)

[Northy]

All we need now is a word shortage of belts and Jimmy's favouritest car in the whole big wide world will be fooked! ;) ;) ;)

G

[jimmy]

:D

the little cars don't need belts, so losi didn't have to move the magic 'belt machine' to producing little rubber bands just yet. :p

[modelimages]

i recieved an email from horizon in the US stating shock towers would be back in stock end of june or early july

[Col]

Just spotted this one on eBay:

http://cgi.ebay.co.uk/Losi-XX4-Front-Shock-Tower-LOSA1204_W0QQitemZ130127897482QQihZ003QQcategoryZ1 40979QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

(not me selling by the way)

[xx4-nutter]

im supprised thats still there.....

Garry D.

[NeilD]

I got two off him and he has two or three left.

[AndyM]

Hi Carl,

any update on the parts?

[Northy]

There's some on Ebay ;)

G

[AndyM]

meant the ally parts ;)

[bigred5765]

ill ring the guy whos doin the engineering tomorrow ill get back 2 ya
should be close now

[rcracer]

http://cgi.ebay.co.uk/XX4-Graphite-Front-Tower-BNIP-LOSA9740-Free-Postage_W0QQitemZ250136899909QQihZ015QQcategoryZ14 0979QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

[rcracer]

And again guys ;)
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=230147547654&ih=013&category=34063&ssPageName=:IT